Search Documents

By Vink L, Johnson N. W, Mackenzie J, Young M. F, Johnston M, Landmark V

The influence of ore textures on metallurgical behaviour is poorly understood for most ores. An alternative method for characterising ore textures and for determining the resulting implications on ore processing has been developed for the Geor

Jan 1, 1998

By C Rogers

"The Coal Seam Gas (CSG) industry has seen a rapid increase in activity over a 30-year periodfrom the early 1990s within Australia. Despite public concerns over environmental issues, theCSG industry has increased in Queensland to the point where more than 90 per cent of naturalgas consumed in Queensland is CSG. The New South Wales (NSW) CSG industry has been slowerto respond for many reasons. Ninety-five per cent of natural gas consumed in NSW comes frominterstate. However, CSG activity in New South Wales is increasing notwithstanding publicconcerns. The CSG potential of three Petroleum Exploration Licenses (PELs) are being assessedwithin the Southern Sydney Basin that provides a unique opportunity to develop resourcesstrategically around many abandoned coal mines. The question has been asked - what do theseabandoned coal mines mean to the project? Are they good or bad? Are they friend or foe? Thispaper att empts to answer these questions and in doing so describes the coal mine ventilation andgas management philosophies and practices used to assess gas production potential. The coalmining philosophies not only have the potential to assist in the construction of a highly successfulCSG project, but they also potentially add signifi cant pre production value by re defi ning how theresources and reserves are assessed and therefore valued. The behaviour of abandoned coal minesand the goaves within the PELs are not well understood by the petroleum industry. However, in the Illawarra region there is an abundance of coal mining knowledge and expertise that if properly focused can greatly increase the chances of project success."

Jun 1, 2012

The Newcrest Mining Limited Telfer Gold Mine consists of an underground sublevel cave (SLC) operation located 734 m directly below active open pit operations. Open pit and underground current production rates are 50 million and 5.7 million tonnes per anum (Mt/a) respectively. The SLC was initiated in late 2006 with breakthrough planned to occur on the 5484 bench of the west wall in late 2009. Risk to the south ramp was identified during this time, resulting in the construction of the north ramp. The SLC was continually tracked from initiation with a suite of monitoring systems and managed with a Major Hazard Management Plan (MHMP) and associated Trigger Action and Response Plans (TARP). At breakthrough the eastern limb of the cave was located within a 70 m horizontal distance from the south ramp. The south ramp was closed in October 2009 due to significant slope deformation, extensive cracking in the berms and batters between the ramp and breakthrough bench and a major failure 250 m to the north of the cave breakthrough. Wall response was first identified from slope deformation measurements taken by the wall monitoring radar in May 2009, at which point the SLC was 160 m from breakthrough. The impact of the SLC on the slope is a unique case with the monitoring systems in place able to provide data on the slope reaction to the SLC progression. This paper will discuss the management of the south ramp such as the early interpretation of risk associated with cave breakthrough, monitoring systems implemented to track the cave progression and wall deformation, data integration and interpretation and risk management. Following the closure of the south ramp further instrumentation programs and risk assessments were conducted to determine the risk of re-opening this haulage route. The outcomes of this program will also be presented.

Nov 25, 2010

By R Forster

Direct ship iron ore (DSO) operations at Extension Hill in Western Australia’s Midwest region have commenced, with fi rst product railed to the port of Geraldton in July 2011. Reserves are 14.8 million tonnes (Mt) of haematite-goethite ore overlying an Archaean BIF-hosted larger magnetite deposit which Mount Gibson Iron Limited (MGI) sold to other parties in 2006.Some unique geological aspects of the deposit shape DSO mining and processing operations. Owner-operator selective mining, blending, crushing and screening on site will produce three million tonnes per year (Mt/a) of Lump and Fines product to be trucked 86 km to Perenjori, railed 232 km to Geraldton, and loaded aboard Panamax-sized ships through the dedicated iron ore shiploader at the Geraldton Port Authority’s Berth 5 facility.The statutory approvals process for this project formally began in 2004, dominating delays in a predevelopment phase which extended over a longer period than the likely life of DSO operations. The lack of transparency, uncertainties and costs inherent in state government processes have influenced decisions made by MGI while assessing other development opportunities in Western Australia. Potential for additional Reserves exists at Extension Hill, however MGI’s ability to extend the mine life will hinge on statutory approval to explore for and evaluate other DSO resources on surrounding granted mining leases.The nature of the resource and use of existing infrastructure for product transport have enabled MGI to keep operating costs and capital intensity of this project relatively low. A tenacious development approach by MGI and robust project economics have fi nally enabled this site to take its place as a revenue earner beside the company’s other DSO operations at Tallering Peak and Koolan Island.

Jul 11, 2011

By R Klepper

Separation of leach residue suspended solids from pregnant liquor solution is an important step in hydrometallurgy flowsheets. Alternative flowsheet options are counter-current decantation (CCD) thickeners or counter current washing (CCW) horizontal belt vacuum filters. Extensive sedimentation and vacuum filtration simulations have been completed by FLSmidth on leach discharge slurries to indentify equipment capacity and performance. These data were used to compare Capex and Opex for CCD versus CCW alternatives. In addition, Capex and Opex for large horizontal belt vacuum filters with filtration areas greater than 250m2 are compared to current state of the art sizes of 150m2. This paper presents this information and discusses various advantages and disadvantages.

Aug 8, 2011

By J Salaya, J Kwak, L Keeney, S Dehkhoda

In addition to volatile commodity prices influencing decision making, in recent years, social and environmental performance have become important decision drivers within the mining industry. There are increased demands from stakeholders, communities, and governments to ensure that raw materials are mined, processed and refined responsibly. The industry also faces the challenge of better managing its waste, which has led to severe consequences when not done properly. The high commodity prices of the late 90s and early 2000s encouraged larger economies of scale and drove mining companies to extract large volumes of rock for separation and concentration at the downstream processes. Over time, as ore grades dropped, the cost of mining escalated and tailings volumes grew. This arduous process also caused strains on recovery cost and performance. Scarcity of water and energy resources coupled with increased production demands and higher operating costs are putting pressure on companies to find innovative ways to increase mining intensities. Hatch’s value chain optimisation methodologies, specifically Grade Engineering® and early waste rejection of the mine, have been of interest to intensify operational performance and minimise waste generation. Enabling preconcentration of the plant throughput, the methodology has significant potential to improve overall metal production and reduce water and energy intensities, whilst minimising wet tailings. Using representative data from real world mines, this paper reports on a case study that evaluates the impact of preconcentration using sensor-based ore sorting on downstream process improvements as well as energy, water and tailings reduction. Financial and economic viability of this technique is presented for both brownfield and greenfield implementation cases. The results show that business case for preconcentration is best when: the distribution of metal in the run of mine ore is negatively skewed and left tailed; mining costs are low; energy, water and tailings management costs are high; and low cost methods of recovering pay metal from low grade material are available.

Nov 10, 2020

By W Liu, S Gao, D Wei, B Cui, Z Guan, Y Shen

Beneficiation of low-grade fine-grained hematite ores becomes increasingly important due to rapid depletion of high quality iron ore resources. However, fine particles, especially ultra-fine particles, make efficient beneficiation of these ores more difficult. Therefore, methods to reduce the influence of fine particles must be considered to achieve better beneficiation performance. Analysis and systematical beneficiation tests were carried out on an ultra-fine-grained hematite ore slime from washing a fine grained hematite ore. Ore particles were found to be presented in loose soil. While some of the ore particles were agglomerated, they were very fine and contained up to 76.5 per cent -0.023 mm material. In this paper, using a single magnetic separation flow sheet with sodium silicate (SS) as a dispersing agent, a concentrate containing 65.05 per cent Fe was obtained at an iron recovery of 68.58 per cent from the hematite ore slime of 56.65 per cent Fe. The single magnetic separation flow sheet was simple and reliable, the agent SS was effective in dispersing ultra-fine particles. The results are believed to be applicable to similar hematite ores.CITATION:Wei, D, Guan, Z, Gao, S, Liu, W, Shen, Y and Cui, B, 2013. Beneficiation study of an ultra-fine-grained hematite ore slime, in Proceedings Iron Ore 2013 , pp 495-500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By G Q. Xie, J W. Mao, Y B Cheng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The East China Mesozoic metallogenic province hosts the world’s largest resources of tungsten, tin, molybdenum, antimony and bismuth, with additional important gold, silver, mercury, lead, zinc, copper, uranium and iron deposits. These deposits form several giant metallogenic belts, including South China, Middle-Lower Yangtze River Valley, East Qinling-Dabie, eastern North China Craton and North-east China. Available data demonstrate that these metallogeneic belts are the products of episodic magmatic and related hydrothermal events between ~240 and ~80 Ma. Each magmatic-hydrothermal episode has produced distinct deposit assemblages that can be readily linked to the Mesozoic geodynamic evolution of East China, involving continental collision between the North China Craton and South China Block at 220–200 Ma, oblique subduction of the Izanagi plate under the Eurasian continent at ca 170–135 Ma and post-subduction extension and lithospheric delamination at 130–80 Ma. Metallogeny in north-eastern China is more complicated due to prolonged tectonic evolution related to southward subduction of the Mongolian–Okhotsk plate and westward oblique subduction of the Izanagi plate, and subsequent continental collision and post-collisional processes.CITATION:Mao, J W, Xie, G Q and Cheng, Y B, 2015. Mesozoic metallogeny in east China and their geodynamic processes , in Proceedings PACRIM 2015 Congress, pp 631–636 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K F. Tang, J-W Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xiong’ershan district in the southern margin of the North China Craton (NCC) contains more than 20 gold deposits hosted in the late Neoarchean to early Palaeoproterozoic amphibolite facies metamorphic rocks or late Palaeoproterozoic unmetamorphosed volcanic rocks. Gold mineralisation consists mainly of auriferous quartz veins and disseminated ores in hydrothermally altered zones, with additional gold mineralised breccia pipes. Gold orebodies are strictly controlled by secondary- or higher-order brittle/ductile-brittle faults. Isotopic dating reveals two separate episodes of gold mineralisation: the Shanggong and Dianfang deposits formed in the range of 236 ± 1.4 to 202 ± 18 Ma, whereas the Gongyu, Qianhe and Qiyugou deposits formed between 135.0 ± 0.5 Ma and 124.0 ± 1.0 Ma. Stable isotope and noble gas geochemistry studies indicate that the Triassic gold deposits were precipitated from deeply-sourced, low-salinity fluids at 250–350°C, but whether the fluids were mainly derived from metamorphic devolatilisation or magmatic degassing remains unresolved. In contrast, the Early Cretaceous deposits most likely precipitated from a dominantly magmatic fluid, although metamorphic and meteoric components cannot be ruled out. Results from this study, when combined with regional geological and geochemical data, suggest that the Triassic gold mineralisation was generated by the deformation associated with the collision between the North China and Yangtze cratons, forming the Qinling-Dabie orogen. In contrast, the Early Cretaceous gold veining was a result of lithospheric destruction of the NCC, a process initiated by plate subduction from both the south and north since late Palaeozoic but ultimately triggered by the westward subduction of the palaeo-Pacific plate in the late Mesozoic. This study helps to reconcile the long-term debate on the timing, genesis and geodynamic setting of gold mineralisation in the Xiong’ershan and other districts along the southern margin of the NCC.CITATION:Li, J-W and Tang, K F, 2015. Gold deposits in the Xiong’ershan District, Southern North China Craton – products of Triassic deformation and Cretaceous craton destruction, in Proceedings PACRIM 2015 Congress, pp 341–344 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

By M Kent, D Elder, J Woodward, R Edwards, B Catto

At Tropicana gold mine (TGM), mine planning is completed from ‘one source of truth’ known as the Integrated Planning Model (IPM). The IPM is a block model which forms a core component of the TGM Mine Planning System – used for short, medium and long-term mine planning cycles, and for Mine to Mill reconciliation.The IPM was developed from a desire to consolidate long-term information contained in mineral resource and ore reserve models, with short-term information from the grade control processes, including grade control models and ore polygons.The IPM is informed initially by resource models, upon which the longer term budget and schedules are based. The IPM is routinely updated with grade control models and ore design information, providing increased confidence for short to medium term mine planning. In this format, the IPM also provides a framework for reconciliation of resource performance with grade control, mining actuals and mining schedules, and ultimately milling. As well as a means for analysing past performance through reconciliation, it has proven its worth as a predictor of variation and an input to successful schedule sequencing and change management. The IPM is a critical component of the TGM Mine Planning System, providing a centralised framework for short interval mill feed prediction through to life-of-mine (LOM) planning.Current development of the IPM is working towards incorporating Mine to Mill optimisation and real-time material tracking projects at TGM. If successful, the model will provide a truly powerful mine planning data source. Current development outlines a mechanism for tracking material from Mine to Mill, and for transferring mill performance data back to the IPM. Increasingly advanced material classification and mine planning, incorporating the multiple geometallurgical variables, will enable the mine to provide consistent mill feed products and result in a steady state and optimised mill.This paper outlines the vision, creation and benefits of the IPM at TGM. It also introduces the ongoing developments to ensure the IPM becomes only more relevant to successful and integrated mine planning as TGM matures from the new kid on the block to the old hand in the neighbourhood.CITATION:Catto, B, Elder, D, Edwards, R, Kent, M and Woodward, J, 2017. An integrated approach to mine planning – building the integrated planning model at Tropicana gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

By A Karrech, E Hamdi

The uncertainty of geomaterials properties is commonly encountered in resource engineering applications, especially in mining engineering where the rock mass texture, joints, fractures and damage zones can impose the mining method and operation cycles. In the present research work, we focus on the elastic properties of rock masses. We use stochastic numerical simulation of fractured rock masses to estimate their Young moduli. The procedure starts with field mapping campaigns which are conducted to evaluate the locations, dip angles, strike and trace lengths of pre-existing fractures. We develop statistical law parameters of the natural fracture network to represent the weakness patterns. In addition, we use HLA-Dissim, a recently developed and validated Matlab program, to simulate the propagation of monochromatic longitudinal waves and derive the equivalent elastic modulus of fractured rock masses. Such procedure applies within a simulation domain, which is greater than an Elementary Representative Volume.At a second stage, we conduct finite element simulations to validate the previous approach. The matrix and the actual fractures zones are reproduced in the model to mimic the natural set-up. The block is excited on particular positions and its response is evaluated on predefined spots. Real field rock fracture mapping data and monitored single-hole blast induced vibrations are used to validate the theoretical and numerical approaches discussed herein. Comparison between the simulated and measured vibration records shows a great agreement which confirms that the proposed methodology has a full potential to predict and optimise multihole/multidelay blast-induced vibrations.CITATION:Hamdi, E and Karrech, A, 2015. A methodology for rock mass characterisation to control blast-induced vibrations, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R G. Skirrow, M Cooper, J Claoué-Long, K Czarnota, H Dulfer, J Thorne, D C. Champion

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits are under-represented in Australia’s inventory of known resources of this deposit type, relative to regions globally with comparable geology. To support discovery of major new deposits, a continental scale analysis of Australia’s potential for tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits is being undertaken. The analysis applies a mineral systems approach to map the four essential components of the ore-forming systems:1. sources of ore constituents2. crustal and mantle lithospheric architecture3. energy sources or drivers of the ore-forming systems4. gradients in ore depositional physico-chemical parameters.The results reveal several regions of Australia with potential for discovery of large tholeiitic intrusion-hosted nickel (PGE-Cu) sulfide deposits, mostly around the margins of Archean and Proterozoic lithospheric blocks. These include the south-east and northern margins of the Yilgarn Craton, the south-west and south-east margins of the Kimberley Block, the southern margin of the Arunta Province in central Australia, the western flank of the Gawler Craton in South Australia, and possibly some areas within the Palaeozoic Lachlan Orogen of eastern Australia.CITATION:Skirrow, R G, Dulfer, H, Czarnota, K, Champion, D C, Thorne, J, Cooper, M and Claoué-Long, J, 2015. Australia’s potential for nickel sulfide ore systems – a new continental-scale time-space framework for exploration, in Proceedings PACRIM 2015 Congress, pp 679–684 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Southern Alps of New Zealand and the mountains of Taiwan are both young transpressive orogens characterised by rapid uplift and exhumation, high heat flow and vigorous surface processes. Comparing and contrasting the two provides an ideal framework through which to explore the structural and lithological controls on fluid and gold mobility during collisional deformation. Both have two fluid flow systems centred about their drainage divide with shallow topographically-driven meteoric water above a deeper flow system dominated by mineralising rock-exchanged fluids. Despite similar tectonic settings, the distribution of heat flow, hot springs and veins in the two orogens are different. Taiwan has higher heat flow, distributed hot springs and localised veining whereas the Southern Alps have a narrow heat flow anomaly, localised warm springs and widespread veining. We use three-dimensional numerical models to evaluate key parameters that affect fluid flow and gold mineralisation. Models show that differences in crustal strength and thickness affect the locus, scale and rate of crustal fluid flow and hence influence gold deposition at a variety of scales. We explore how surface topography can lead to localised changes in the stress state, facilitating the switching of principal stresses and hence vein orientations.CITATION:Upton, P and Craw, D, 2015. Modelling structural and lithological controls on the mobility of fluids and gold in orogenic belts – examples from New Zealand and Taiwan, in Proceedings PACRIM 2015 Congress, pp 189–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The sudden. explosion of relatively inexpensive digital process control computers has accelerated interest in the possibilities of economic savings by their use. In particular the metalliferous industries have shown that they are willing and capable 6f grasping this new technology and putting it to good use. These industries have a number of problems which need special attention. In many cases the process is difficult to measure and a reaction is often controlled by measuring a secondary effect, computing its relationship to the reaction and then applying the necessary corrective action. This creates problems in building the process model, designing the computer to process interface and in the subsequent system development. Environmentally the metalliferous industries create conditions which severely test sophisticated electronic equipment. Care taken in locating and housing this equipment is a major factor in ensuring reliability in Operation.

Jan 1, 1977

By J P. Jona, S R. Poulson, C H. Gammons

Spatial and temporal trends in water chemistry in the acidic (pH ~2.6) Berkeley Pit lake, Butte, Montana, can be explained by a newly developed iron-cycling model. Key elements of this model include: subaqueous oxidation of pyrite and other metal sulfide minerals by dissolved ferric iron, producing Fe2+ as a by-product; re-oxidation of Fe2+ to Fe3+ in the epilimnion, assisted by A ferrooxidans; precipitation of secondary ferric minerals (schwertmannite, jarosite) in the epilimnion; and replenishment of the Fe3+ concentration of the hypolimnion by seasonal lake turnover and gravitational settling and re-dissolution of ferric precipitates. Pyrite oxidation rates were approximated by using published rate laws and information on the Fe3+ concentrations (~5 mmol) of the Berkeley Pit as a function of depth. The results indicate that subaqueous pyrite oxidation may be releasing as little as 6 + 106 or as much as 600 + 106 moles of H+ each year to the lake; the large range reflects uncertainty in calculation of the specific surface area of pyrite in the flooded pit. This helps to explain the observation that the pH and metal concentrations of the Berkeley Pit have not improved with time since mine flooding began in 1983. Vertical cycling of ferric iron in the pit lake permits pyrite oxidation to continue in deep water, even in the absence of dissolved oxygen. This hypothesis is supported by preliminary stable-isotope data.

Jan 1, 2003

The international scientific and engineer-ing community is being challenged to take advantage of the opportunity offered by the U.N. International Decade for Natural Disaster Reduction (IDNDR) program to reduce rapid onset geological hazards along the Pacific Rim. Natural disasters observe no national boundaries; international cooperation offers the best opportunity to reduce the losses these catastrophic events create.

Jan 1, 1990