Search Documents

By Soorkty Elarabi

The aim of this paper is to discuss the impact of end bearing plate on the capacity of micropile. Preliminary studies have been made in Sudan in specific area of cohesive soil. Experimental works were carried on a number of micropiles with and without end bearing plate. Same diameters, lengths and techniques of placing cement grout are considered, there after the axial load test applied to find out the capacities of micropiles in both cases. Deduced results in each case show that the end bearing plate has no positive impact on micropile capacity.

Oct 1, 2022

By Joanna Bzówka

Nowadays, there are some new requirements for the supermarket floors. The floors are loaded by high point- and moving-loads. In spite of this fact, it is necessary to ensure the stiffness of the floor and the stiffness of its support. When pile foundations are designed in the case of weak soil, the piles are recommended under the foundations of the supermarket and also under the floor layers. The example of foundation of a typical supermarket located on long­standing municipal dumping ground is presented. Indirect foundation - CFA piles, 0.5 m in diameter and 4.5 to 20.0 m long, was de­signed. Fifteen trial loading tests were carried out.

Jan 1, 2006

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Marius B. Wechsler

A mathematical analysis is developed for the determination of the cases when HP-piles might be replaced by precast concrete piles. The analysis focuses especially on the "integral abutment-bridges" which are used on large scale in the Great Plains of the United States of America, The theoretical considerations are illustrated by a numerical example.

Jan 1, 1992

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Rohrbach

Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project?s critical path, the benefits obtained in terms of project savings and reducing costly delays are undoubtedly valuable.

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Greg Nutson, Jeremy Butkovich, Bill Perkins, Hollie Ellis, Paul Bott

"Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.INTRODUCTIONThe Evergreen Point Bridge conveys State Route (SR) 520 2.6 miles (4.2 kilometers [km]) from Seattle to Medina across Lake Washington. The bridge is located in a seismically active area, and the Washington State Department of Transportation (WSDOT) has determined that the western half of the 1960s-era bridge (the “west approach”) is vulnerable to earthquake damage. WSDOT has begun preliminary design to replace the west approach bridge.The west approach extends about 6,100 feet (1,900 meters [m]) east from Seattle’s Montlake neighborhood, over Union Bay and Foster Island, then into Lake Washington proper (Figure 1). Approximately 5,600 feet (1,700 m) of the replacement bridge would be constructed over water. Subsurface conditions along the bridge alignment consist of 5 to 80 feet (2 to 24 m) of very soft peat and clay, over very dense/hard sand and clay. Multiple pile supported columns support the existing bridge. The new bridge would be supported by 8- to 10- foot-diameter (2.4 to 3.0 m) drilled shafts that extend about 50 feet (15 m) into the underlying very dense/hard soil. To reduce seismic demands on the bridge superstructure, WSDOT has decided to incorporate a base-isolation system into the bridge design."

Jan 1, 2017

By Rick Ellman, Ian Chaney

"The Hampton Roads area encompassing the Norfolk, Virginia Beach and Newport News metropolitan region experiences some of the worst traffic congestion in Virginia. With continued growth of the ports and increasing demand, the Virginia Department of Transportation (VDOT) initiated the Downtown Tunnel/Midtown Tunnel/MLK Expressway Project, a complex undertaking critical to addressing the Hampton Roads area’s transportation needs. The project is a $2.1 billion Design/Build/Finance/Operate (DBFO) endeavor most notably involving the construction of a new two-lane vehicular tunnel utilizing the Immersed Tube Tunnel (ITT) method. The tunnel will pass under the Elizabeth River parallel to the existing Midtown Tunnel between Norfolk and Portsmouth, Va. It will be the largest design-build project constructed in the history of the Hampton Roads District.The New Midtown Tunnel will extend approximately 6,450 ft (1,966 m) along the north side of the existing tunnel where it ties into the existing Midtown Tunnel approaches in Norfolk and Portsmouth. It is being installed in a pre-excavated trench of which approximately 2,250 ft (686 m) required bracing on the Portsmouth side and approximately 1,000 ft (305 m) required bracing on the Norfolk side. The remaining 3,200 ft (975 m) of trench excavation was open cut dredging with laid back side slopes, optimized to reduce dredging, disposal and backfill quantities while also reducing the risk to the existing tunnel. The braced excavation portions of the tunnel alignment were divided into distinct segments which include: Portsmouth Approach Boat Section, Portsmouth Approach Cut-and-Cover Section, Portsmouth Dredge Section, Norfolk Dredge Section, Norfolk Approach Cut-and- Cover Section and the Norfolk Approach Boat Section. All “approach” excavations were performed in the dry and all “dredge” excavations were performed in the wet. Eleven ITT segments are being fabricated in the Sparrows Point Dry Dock facility in Baltimore, Md., and each 14,000 ton (12,700 tonne) segment is being towed approximately 220 mi (354 km) to the site. The ITT segments will extend under the Elizabeth River, with the deepest crossing 90 ft (27 m) at the Federal Navigation Channel. Once beyond the channel limits the ITT rises at an approximate 4.5% slope. Controlled screeding and element lowering operations will be performed primarily from floating barges."

Jan 1, 2014

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By Luo Yang

A one-dimensional wave equation based algorithm for estimation of shaft and toe resistance of driven piles using High Strain Testing (HST) data is presented. The pile is represented by a uniform elastic bar, while the soil around the pile is assumed as a homogenized isotropic medium, and Smith model is adopted to represent soil-pile interaction in the wave equation analysis. In most cases, the displacement of pile particles along pile shaft is greater than recoverable soil deformation (i.e., soil quake in Smith model). Therefore, static shaft resistance could be reasonably assumed to be totally mobilized during pile driving. Smith damping factor is used to account for combined dynamic and rate effect. Force and velocity time histories measured at the pile head are used as input boundary conditions in an analytical solution of the one-dimensional wave equation. As a result, two unknown parameters, static shaft resistance and Smith damping factor, can be incorporated into the one-dimensional wave equation and determined analytically for the time duration prior to the first downward wave reaching the pile toe. Then, soil resistance and Smith damping factor at pile toe can be further determined. The advantage of the proposed analysis technique is that the Smith damping factor and the static soil resistance can be directly determined based on the closed-form solution of the one-dimensional wave equation, which is computationally efficient. Numerical examples are given to illustrate the use of the proposed method to determine the pertinent Smith model constants and the static resistances.

Jan 1, 2006

By Wen Songlin

This paper presents an experimental program to investigate the behavior of a pile with wings under horizontal loads in sand at laboratory. The work focused on evaluating the lateral resistance behavior and the geometric effect of wing board on the horizontal resistance. Based on the measured data and observed phenomenon, the following behaviors have been observed: 1) A pile with wings is not only a powerful means to improve the horizontal bearing capacity of a pile foundation but also economy and feasibility; 2) The horizontal bearing capacity of a pile with wings increases with increasing of it?s wing board?s area; 3) The pile lateral capacity is also influenced by the wing board?s geometric shape. Under a certain soil and pile condition, there is a critical embedment depth of the wing board, which will yield the maximum horizontal bearing capacity. It was further observed that when the displacement of the pile head increases, part of the horizontal bearing capacity of the pile is developed by the so-called shaft?s anti-pulling capacity.

Jan 1, 2007