Search Documents

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By J. Shibata

The behavior in electric field of fine particles present in aqueous solution was measured in order to apply to the classification of fine particles. The sample particles used are spherical polystyrene particles with the average diameter of 0.03 µm, 0.1 µm, 1.0 µm, 4.3 µm and 9.6 µm. Electrophoretic mobility and zeta potential of various particles are measured by an instrument based on the principle of the laser Doppler effect. The influence of temperature, electrolyte concentration on the electro-phoretic mobility was investigated for various polystyrene particles. The electrophoretic mobility increases with increasing pH and temperature of suspensions. The measured electrophoretic mobilities are different from electrolyte concentration and particle size. The electrophoretic retardation effect and relaxation effect are considered to explain the behavior of fine particles in electric field by applying the electro kinetic theory of Wiersema et al. For all particle size, the electrophoretic mobility decreases rapidly in high concentration of KNO3 such as 0.1 mol/dm3due to the compression of electric double layer The forces acting the particles in electric field are considered to be electrical force, friction force and some other forces like relaxation effect and electrophoretic retardation effect which appear in ionic behavior. It is considered that the particle moving velocity depends on the particle size. When the particle size is less than 1µm, the velocity increases with increasing the particle size. On the oth-er hand, the velocity deceases with increasing in particle size, when the particle size is larger than 1µm. This phenomenon is considered to be interesting from the viewpoint of classification for fine particles. We found that the electrophoretic mobility of 1.0µm particles is larger than that of 0.1µm particles, and that it is possible to classify fine particles by using the difference of electrophoretic mobility by many experimental results. The phenomena can be explained by the forces acting the fine particles in the electric field. We can apply the behavior to classification of fine particles.

Jan 1, 2014

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By Bert Huls

Already starting, new drivers will dictate how future mineral processing plants will be designed and operated. These drivers include requirements in water and energy conservation because of rising costs, larger demand for mineral and metal products as the result of a rising population, and the increasing demand from the population in general to have influence over what type of operations will be developed where. Mineral operating facilities will require processing of lower grades. To do this economically, design engineers will be influenced to introduce newer concepts, or return to older processing concepts once deemed not desirable. Our understanding of the fundamentals must be improved, and this may come from better measurement techniques and more process piloting, and will go in hand with a reduction of waste generated during the process, improved separation of minerals or product size. Process engineers will also be required to not just design according to the established 3D methodology for efficient plant installation. Already in other industries the design concept encompasses the entire range from source to product. Not only that, the design will be affected by public influence that must be illustrated prior to project execution. On the one hand, the added dimension in design may slow a project; on the other hand it may result in a blessing, and in a higher responsibility for engineering.

Jan 1, 2014

By Xin Tan, Changgen Li

"The floatabiliby of chelate CF-collector for zinc and lead oxide minerals was described. It found that CF-collector possesses a strong collection power for zinc and lead oxide minerals as well as excellent selectivity for the gangue minerals. A new technology of zinc and lead oxide flotation with CF reagent as a collector, lead nitrite as a activator and water glass as modifier was presented. The mechanism of interaction between reagents and minerals was discussed by means of adsorption, zeta potential, nephelometric titration, XPS and infrared spectra was investigated.CF-collector, newly developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM), is a kind of chelate collector for the flotation of oxide minerals. CF-collector mainly consists of N-nitroso-N-phenylhydroxylamine ammonium salt. The CF-collector was used for the selective flotation of scheelite in the Chinese plants.In this paper, the effects of the dosages of activator Pb(NO3)2 and depressants (sodium hexametaphosphate, polyphosphate, water glass and salified water glass) on the floatabilities of several minerals (cerussite, smithsonite, calcite, dolomite, limonite and quartz) as well as their mixtures were investigated in the presence of the CF-collector. The results show that the CF-collector is the excellent collector for selective flotation of cerussite and smithsonite. Pb(NO3)2 can selectively activate the oxides of lead and zinc resulting in a decrease of the CF-collector dosage. The sodium hexametaphosphate plus the salified water glass are the effective depressants for gangue minerals. Based on the above facts, the “CF process”, namely, used CF reagent as a collector, Pb (NO3) 2 as a activator, and sodium hexametaphosphate plus salified water glass as depressant, has been used for the flotation separation of the lead oxide mixtures or zinc oxide mixtures without disliking and heating. For the feed lead assaying 19.07%, the lead concentrate assaying 49.81% Pb at the recovery 80.69% was obtained after one step flotation. For the feed zinc assaying 12.85%, a zinc concentrate of assaying 29.56% Zn at recovery 83.87% was obtained."

Jan 1, 2003

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By Williams Calderon, César Arredondo, Gonzalo Montes-Atenas

The quality of final concentrate in froth flotation circuits is largely dictated by the correct implementation of the froth washing operation in flotation cleaning stages, which are commonly installed in column flotation cells. In flotation plants, this aspect has been largely overlooked and the froth washing is restricted to the use of perforated piping through which process water flows producing a similar effect to that observed in "fountains": jet created with low energy crosses the froth phase washing out entrained particles as well as particles weakly attached to bubbles. The aim of this research study is to assess the efficiency of traditional froth washing systems theoretically and experimentally. A theoretical model was implemented using Fluent® software where a jet of variable speed was introduced in a continuous soft matter phase with physical properties similar to those observed in a froth phase in wet and dry conditions. In addition, a simple experimental protocol was designed to validate the model. It was found that the water process jet-like flow influences the behavior of 2 to 3 times the equivalent volume in the froth phase. Such influence zone is dramatically reduced as the froth phase becomes drier. These results were confirmed by the experimental findings indicating that a better froth washing technologies must be assessed and implemented. Some aspects of the ideal froth washing system are derived and discussed in details.

Jan 1, 2014

By Güven Önal, Zeki Dogan, Neset Acarkan

"In general, the processing of glass sand may involve comminution, washing, wet classification and attrition scrubbing. Additional processes may include magnetic separation, flotation and leaching in various combinations.Yaliköy sand dune deposit is located near to Istanbul on the European side by the Black Sea coast. The reserve of deposit is around 70 million tons. Iron content of Yaliköy sand dunes is 0.48 % Fe2O3 and not suitable for glass manufacture. The iron content of glass sand should be less than 0.15 % Fe2O3 for window glass manufacture and 0.05 % Fe2O3 for glassware. In this study, it was aimed to produce glass sand with less than 0.15 % Fe2O3 for window glass and with less than 0.05% Fe2O3 for glassware manufacture from Yaliköy sand dunes. A representative sample with a weight of 200 kg was taken from Yaliköy sand dunes deposit through opening small pits.• Mineralogical studies have shown that iron is present in three forms:• Hematite, limonite, clay and iron silicate minerals such as epidote and garnet occur in free form.• Quartz grains are coated by hematite and limonite.• Iron is also present in the cracks of quartz grains.Free iron minerals such as hematite and limonite and silicate minerals were subjected to magnetic separation and flotation for removal. Iron coatings were tried to be removed by scrubbing and leaching. Iron removal in the cracks of quartz grains was attempted by grinding and leaching.Under optimal conditions, sand concentrate with 0.38 % Fe2O3 was obtained by means of high intensity disc type magnetic separation. Grinding and scrubbing were applied to see the effect of size reduction and attrition at room temperature and 90 ºC, by using non-magnetic fraction. Sand concentrate with 0.13% Fe2O3 was obtained at 90 ºC in this test.Sand sample which was previously ground to minus 0.5 mm and scrubbed, was floated by using sulphonates as collector. After flotation tests, sand Concentrate was obtained with 0.11 % Fe2O3.The optimum iron removal was achieved by H2SO4 leaching at 90 ºC depending on acid concentration and leach duration in static, percolation and agitation leaching. Agitation leaching was done by the use of mixer at 600 rpm, 50% solids and leach duration was 15 minutes."

Jan 1, 2003

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. In contrast to landfill and incineration, application of digested sludge comprises the recycling nutrients and organic matter and reflects the policy of resource conservation and sustainability in waste management. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.The digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was the first merit to apply the sludge to agriculture in dry areas. Secondly, the sludge was rich in macro-nutrients (N, P, K) and a series of micro-nutrients (Ca, Mg, Mn, Na, Fe, Cu, Zn, B). The water-soluble fractions of macro-nutrients in the sludge were found considerably low. This implied that the loss or leaching of the macro-nutrients from the anaerobic sludge to the aqueous environment be slow. The nutrients loss owing to leaching could be reduced. However, because of a lower macro-nutrient content of the anaerobic sludge, comparable to the chemical fertilizer, it is advisable that the anaerobic sludge be applied together with commercial fertilizer to the agriculture land. Thirdly, the anaerobic sludge had strong selective adsorption affinity for heavy metal ions; non-heavy metal ions such as K(I) and Ca(II) could be released easily from the sludge in a wide pH range, such as pH from 1.0 to 8.0. Since the metal toxicity to the environment mainly comes from the mobile heavy metal ions, the selectivity to adsorb heavy metal ions of the anaerobic sludge can be utilized to reduce the availability of heavy metal ions to plants and humans in aquatic environment. Fourthly, the anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion."

Jan 1, 2003

By Herman D. Mendoza

"The removal of finely dispersed mercury from the effluent of small-scale gold mining operations and the eventual recycling of the recovered mercury was investigated. The conventional method of amalgamation, or “ball milling”, involves the mixing of a substantial amount of mercury with ore to recover free gold during the grinding stage. During grinding, a portion of the mercury is transformed into minute droplets, which readily float and disperse in the effluent. A kilo of gold ore containing 20-30 g Au/t, when ground with 3 g of mercury, yields 0.005 to 0.050 mg/l of mercury in the effluent, exceeding the concentration of 0.002 mg/l allowed by law for surface water.A rapid recovery/ recycling process was introduced using the surface-chemical properties of finely dispersed mercury in aqueous suspension. It was observed that fine droplets of mercury in an aqueous environment readily attached onto a collector having positive surface potentials for pH 3 to 10. An example of a suitable collector is alumina (Al2O3), which has an iso-electric point of pH 9.8. When an effluent, coming from a settling procedure after an amalgamation-grinding stage, was passed through a column-bed packed with alumina fiber, removal and subsequent collection of finely dispersed mercury occurred under acidic conditions, pH 3-6. Recovery was around 99.5%, yielding an acceptable quality of water safe for disposal into the aquatic environment. The collected droplets of mercury, which are left in the column-bed of alumina fiber, were subsequently treated with a cleansing solution at alkaline conditions pH 10 -12. At these conditions, both mercury and alumina fiber carry negative surface potentials, which results in the eventual detachment of attached mercury from the alumina collector. The effective recovery of attached mercury from the alumina collector by the detachment procedure is only 30-35%. The collected mercury from the cleansing stage can be collected, cleaned and can be used for subsequent amalgamation processes. The attachment and detachment behaviour of finely dispersed mercury onto and from the microscopic collector alumina is shown in Figure 1. The result of attachment and detachment were analyzed using existing interaction energy theories like the Darguin-Landau- Verwey- Overbeek (DLVO) Theory."

Jan 1, 2003

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By Sergey Gudkov, Yuri Yemelianov, Stanislav Balikov, Andrey Boldyrev, Andrey Bogorodsky

"The results of POX of refractory gold-bearing concentrates using halide-ion as a lixiviant for precious metals and activated carbon as an adsorbent are given. It was found that gold did not recover to the solution when halide was added during POX. Silver partially dissolved in the solution. When halide-based reagents and activated carbon were added during POX, gold dissolved and loaded onto the activated carbon. The degree of sulfides oxidation was 99.3-99.6%. The recovery of gold onto granulated carbon was 94.7-94.8% when using chlorine-bearing lixiviants: NaCL, CaCL and carnalite and 98-99% when using KJ and KBr. This treatment process of refractory gold-bearing concentrates combines sulfide oxidation, dissolution and adsorption of precious metals. The results of the metals recovery achieved using this process can be compared with the recovery during POX-cyanidation. In this case, sodium cyanide was not used. This allows the reduction of capital and operational costs due to the absence of cyanidation, CIL and detoxification of leaching tailings circuits."

Jan 1, 2014

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

"INTRODUCTIONThis paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.OPTIMISATION MODEL FOR LINKING DESIGN TO RECYCLINGImproving the efficiency of the material cycle of the car is essential to ensure a sustainable development of our society as well as e.g. to comply with the recycling targets imposed by EU legislation. In the design of the car various materials are combined and connected in many different ways, making up the complex 'mineralogy' of the car and its components, which is changing rapidly and continuously over time. The liberation of materials during shredding plays an important role in the composition (and quality) of the intermediate recycling streams. In order to include the influence of product design (mineralogy), liberation, and particle composition (quality of the intermediate recycling streams) in the optimisation of the recycling of end-of-life vehicles, a systems engineering tool for optimisation of the recycling of end-of-life vehicles was developed, including a liberation model. The optimisation model predicts the recovery rate as a function of product design (in this case a car), liberation, efficiency of the different process steps, economy and legislation based on a developed recycling flow sheet for end-of-life vehicles. Optimisation can only be achieved through the combination of the knowledge areas of product design, shredding, mechanical separation technology linked to pyro- and hydrometallurgy, composing a complex interconnected network of unit operations."

Jan 1, 2003