Search Documents

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

By Peter Ay, Vincenz Mehlstaubl, Satyanarayana Narra

"This study gives an insight into non-destructive testing methods suitable for porosity analysis at a small scale, firstly summarizing relevant state-of-the-art technology and pending patents, secondly realizing and documenting the start-up of the VHX-2000 digital microscope by the manufacturer Keyence and thirdly demonstrating practical application with the extended analysis of three fundamentally different agglomerates for which important application-related parameters are determined. Various analysis procedures on the different agglomerates the efficient and timesaving operational features of the digital microscope are outlined. Firstly an analysis of flax fibre agglomerates determines the process conditions best suited to produce agglomerates with specific properties by determining sphericity, cubicity, density and porosity as well as fibre damage and alteration. Secondly the production of iron-hydroxide - hemp-fibre agglomerates serves to obtain information on porosity values as a result of a cauterization of the fibres. The third analysis provides estimations of porosity values for acid-treated lignin agglomerates. Measurements were carried out with compact dry agglomerates and with soaked, expanded agglomerates, determining factors for total water carrying capacity. Practicability of non-destructive testing by digital microscopy is demonstrated and explained concerning the applications in this study by obtaining definite structural findings about the analysed agglomerates. Information on its operation is made available by a practice-oriented manual for the VHX-2000 digital microscope. Further suggestions for more in-detail analysis results with different instruments are given."

Jan 1, 2014

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By Sudarshan Martins, Peter Radziszewski

"Tumbling mills are machine, operating in non-equilibrium, capable of applying forces on the ore contained within, causing the ore to break down. The action of the mill on the ore is very inefficient, producing a large quantity of heat. The inefficiencies of the mill drive the desire for improvement, spawning research and development activities. Given the non-equilibrium nature of the mill, the theory of Large Deviations is proposed as the framework that captures the state of the mill. The theory of Large Deviations allows for the determination of the rate function and the scaled cumulant generating function (SCGF), for systems in either equilibrium or non-equilibrium. Powerful connections can been made between familiar concepts of statistical physics and the concepts introduced by the theory of Large Deviations: entropy can be associated with the rate function; the scaled cumulant generating function with the free energy. It is shown that observables, compatible with Large Deviation theory, can be identified for the tumbling mill. Here, the time series of the energy associated with an element of the charge is such an observable. Furthermore, using some experimental data, it is shown that the time series of the energy can define a rate function, thereby describing the system within the Large Deviation framework. Finally, a discussion of the results is given, particularly how this theory can be further developed for tumbling mills."

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By Brian Lindner, Lidia Auret, Niel Knoblauch

In this paper, a fault detection and identification framework based on feature extraction and topology extraction methods is proposed, and evaluated on a simulated base metals refinery high pressure leaching process. Feature extraction methods included linear and kernel principal component analysis, while process topology information was extracted with linear cross-correlation, partial cross-correlation and transfer entropy. Connectivity maps were constructed to identify possible fault propagation paths to aid root cause analysis. The results indicate that process topology can enhance the fault identification capability of data-based process monitoring methods. The study of the considered base metals refinery pressure leaching process is ongoing, with future work including the creation of a fault library which would lead to further critical evaluation of the proposed fault detection and identification framework.

Jan 1, 2014

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

The energy dispersion X-ray fluorescence (EDXRF) analysis technique is a rapid and accurate method for describing sample?s element component and percentage composition. On the base of profound research for the national and international development and research condition, the author researched the EDXRF analyze technique and the EDXRF analyzer?s principle in depth, the difficulties and the key points for research and development of EDXRF analyzer; gave a scheme for re-search of bench EDXRF analyzer; researched some algorithms used in energy spectrum analysis; developed the energy spectrum analysis software based on the Visual C++ 6.0; together with the energy spectrum analysis software, the author designed and processed the structural of the bench XRF analyzer and integrated the import X-ray tube, thermoelectrically cooled Si-PIN photodiode X-ray detector and pulse amplitude analyzer as a model machine. The result shows: The model machine can be used in multi-element analysis at the same time for different types of dry mineral samples, with fast analysis speed, accurate model and high stability.

Jan 1, 2014

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

By Jun Qiu, Ping Chen, Xianjun Lu

Nitrogen of different forms from wastewater was adsorbed by the natural bentonite and modified bentonite. The effects of adsorption conditions on the nitrogen removal were investigated. The experiment results showed that natural bentonite could easily adsorb ammonia while poorly adsorb nitrate, the organic bentonite modified by octadecyl trimethyl ammonium could effectively adsorb nitrate with the removal ratio increased from no more than 5% to 89%. Two kinds of bentonite were added together to the simulated wastewater which contained ammonia nitrogen of 15mg/L and nitrate nitrogen of 10mg/L, the dosages were 1.0g respectively. Both ammonia and nitrate had significantly decreased on conditions that the oscillation time was 1.0h and room temperature 20?. The optimum pH value for ammonia removal was 7 while for nitrate removal was above 7. The adsorption isotherm fitting results indicated that the Freundlich adsorption isotherm was the better model to describe ammonia adsorbed on the natural bentonite and the saturated adsorption capacity was 10.25mg/L, while the Langmuir isotherm could better describe the adsorption of nitrate on the organic bentonite and the saturated adsorption capacity was 14.35mg/L. Fully considering the interaction between different ions and controlling the appropriate conditions, removing nitrogen from wastewater by adsorption of bentonite is an economic and effective method.

Jan 1, 2014

By Lilong Huang, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Graphite is the key raw material of new carbon materials such as graphene and spherical graphite. The size and completeness of graphite flakes directly affect the performance of new carbonaceous materials.The research aims to increase the yield of large flake graphite by way of preventing the flake graphite from being damaged during the grinding process. A series of grinding and flotation studies on the flake graphite samples of Yichang in Hubei Province were carried out by vertical stirred mill . The damage coefficient L characterising the degree of graphite flake fractured and corresponding formula was proposed to determine the quality of the grinding and grinding of the flake graphite. The way the damage coefficient L of graphite flake would be affected if with different mill, different media material and size, stirrer speed were investigated. The test results show that vertical screw stirred mill helps the protection of large flake of graphite as well as the graphite liberation. When grinding to the same fineness, the damage coefficient L of graphite flake is 1.20 for vertical stirred mill, while the damage coefficient is 2.93 for ball mill. Minimum damage coefficient of graphite flake was obtained when using 6 mm polyurethane coated ball as grinding media, under the condition that rotation speed of the stirrer within the range of 100~130r/min. The grade of graphite in the concentrate floated from the ground product was 94.16%, the rate of recovery for graphite was 94.66%, and the content of +0.15mm was 54.83%.1 INTRODUCTION Flake graphite is a very important non-metallic mineral[1,2],and due to its special flake structure, the greater the scale and the higher the C grade, the value of its application is larger too. Therefore, in the grinding of graphite sorting process, We should minimize the destruction of graphite scales.. In this paper, graphite mine in Yichang, Hubei Province was used as the raw material for the study. Rough concentrate with C-grade of 36.49% was prepared by rough grinding and coarse separation. Then a series of grinding and flotation studies on the rough concentrate were carried out by vertical stirred mill , which aims to increase the yield of large flake graphite and to provide technical support for improving the beneficiation process of graphite ore."

Jan 1, 2018

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By G. Mucsi

This paper deals with the laboratory investigation of cathode ray tube (CRT) glass based glass foam, a relatively new product so called ?Geofil bubbles?. The main process engineering material properties of raw materials, such as particle size distribution, moisture content, density and specific surface area are shown. Then the preparation of raw cathode ray tube glass waste is presented including the following steps: crushing in impact crusher, grinding in laboratory scale ball mill, mixing, pelleting and sintering. We found that it was possible to produce foam glass (with proper mechanical stability and particle density) from the investigated waste CRT glass. The material characteristics of the final product strongly depend on the sintering conditions. Optimum conditions were determined particle size fraction was found to be 4-6 mm, temperature 800 0C, residence time 7.5 min. Keywords: waste CRT glass, grinding, pelleting, sintering, glass foam

Sep 1, 2012

By D. J. Hallbom

The ?yield plastic? rheological model describes the flow behaviour of a variety of non-settling suspensions, including many types of mineral slurry. The current paper presents the laminar flow relationship (pressure gradient vs. flow rate) for a yield plastic fluid flowing through a pipe or cylinder. Simplified algebraic equations, suitable for engineering purposes, are presented for yield plastic fluids with values of the scaling factor in the range that includes most industrially important slurries. The laminar pipe flow relationship is one of the most important fluids engineering calculations. It may be used to determine the rheological parameters of a material in a capillary rheometer or flow loop. If the rheology is known, these relationships may be used to determine the laminar flow pressure gradient in pipelines of various sizes.

Jan 1, 2014