Search Documents

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By Liu Chun-Bao Sun, Hong-Jun, Wei Zhang, Tao Xu

SABC circuits have gained widespread attention within China, and are being gradually applied to many mines. However, the domestic knowledge of comminution process is still relatively basic, and the design and production management of the application of SABC technology lack guidance of scientific theories. This research project focuses on the Phase I SABC milling circuits of Wu Shan Porphyry copper mine. Targeting the design and operation problems of existing process and circuit, and without increased investment and alterations in equipment, the new technologies will combine ordinary crushing and grinding theories as theoretical guidance, and borrow JK Simulation Software (JKSimMet) for analysis in order to optimize the comminution process, efficiently allocate production output and energy consumption, eventually resulting in increased production and energy efficiency. Using JKSimMet Simulation Software, and combining theoretical optimizing and practical production techniques, as well as the on-site situation, the eventual SABC comminution process and circuit optimization plan is: increasing the grinding Ball charge from 8% to 10% v/v in the SAG mill; Setting the Ball charge in the Ball mill to 27% v/v and the maximum operating power draw to 5 800kW; replacing the HP Series crusher with a TRIO TC84 crusher, which is without a power controller, and adding a pebble bin. The final optimization result is: Maximum system processing capacity increased between 20%-26.7%, specific energy consumption reduced by more 2.0 kWh/t, creating an economic benefit of over 300 million RMB, thus achieving the goal of increased production, reduced energy consumption, and improved profitability.

Jan 1, 2014

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Industrial minerals may contain the same elements in approximately the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques.• quantitative measurements by ebsdCommon automatic techniques describing the mineral contents and the occurrence of minerals in free and locked particles, are based on optical-, backscattered electron (BSE)- or X-ray-signals. There are various commercial software systems on feature analysis by backscattered and X-ray signals in combination with image analysis (e.g. Oxford Inca Feature, CSIRO QemScan).Especially in silicates, the occurrence of similar elements in the different minerals is common. Sometimes the various minerals not only contain the same elements, but also approximately the same amount of each element. In these cases BSE imaging and chemical analysis are not always sufficient for identification."

Jan 1, 2003

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. The image processing was performed using the Smartfroth software on the top surface of the froth. The system gives measurements of bubble size distribution, average bubble size and froth velocity. The froth velocity was used to estimate the volume of bubbles overflowing the weir yielding to the fraction of air overflowing the cell. This measurement is the complement of the rate of bubble bursting on the top surface. Also samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. Then, the amount of solids and liquid per unit area in the bubble lamellae was estimated gravimetrically. Both measurements were used to establish stability criteria.It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase to high frother dosage did not result in an improved fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance."

Jan 1, 2003

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Ltd. Kyushu Metal Industry Co., Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

"Actually, the recovery of valuable metals such as iron, aluminium and copper is a nowadays practice in factories dealing with the processing of scrapped automobiles (Harder (WERG); Koga et al., 1997). This process has reach a recycling rate of about 75%, and generates a huge volume of waste (including cottons, sponge, plastics, rubber, etc…), locally known as “shredder dust”, which is commonly dumped on landfills; its recycling is either unsatisfactorily or not yet performed (Keller and Schebdat, 2000).The saturation and depletion of valuable disposal sites in the not-so-distant future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry.To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of a calibrated (–80+5mm) shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-weight materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively. A sedimentation tank is used to recover the light-weight materials deported in the heavy fraction stream."

Jan 1, 2003

By Jurgens J. Louw, Vincent C. Smith, Gareth C. Smith, Agit Singh, Dave G. Hulbert

"During 2000 Mintek Developed the PlantStar plant wide control platform for the minerals processing industry. The flexibility of the PlantStar control platform has enabled Mintek to investigate and easily develop new control strategies for both milling and flotation. This includes a Solids Feed Controller, a Safety Limit Controller, Mill Power Optimiser and Flotation Optimiser, amongst others.Processes with long dead times, like a feed belt to a mill, are difficult to control. The solids feed controller was developed for minerals processing plants using a specialised time delay compensator. Using conventional time delay compensators that are purely model based, results in robustness problems due to model uncertainties. The Mintek Solid Feeds Controller makes use of a plant model, but compensates for model inaccuracies, giving more controller stability and a more robust delay compensation algorithm.Often there are more variables on a plant that need to be controlled (process variables) than there are variables to control them with (manipulated variables). Process constraints are often reached and violated. Safety control loops are necessary to prevent constraints being reached. The safety limit controller has been developed to switch smoothly between normal and safety control loops without bumping the process. The safety loop output is chosen in accordance with a predefined list of priorities and whether the respective constraint boundaries are exceeded.The Mill Power Optimiser helps to find the power peak on the mill power curve. It continuously perturb the solids feed rate to learn ‘where’ on the curve the mill ‘was’ and then to drive it continuously toward the middle, maximum power drawn. This insures maximum grind with maximum throughput. It also prevents power dips due to mill overloads by cutting the solids feed to a minimum if the power drop below a specified threshold. Once the power rises above the threshold the solids feed is increased again to an intermediate value from where it start the perturbations again to find the maximum. This makes the milling circuit easier to operate."

Jan 1, 2003

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Huge electrochemical investigations have been performed on Technical faculty in Bor (Serbia) which main goal was the clarification of the copper sulfide minerals behaviour in hydrometallurgic and flotation processes. Modeling of these processes was a part of the effort for better understanding of the reaction mechanisms.The consideration of electrical analog circuit and mathematical model of processes at interfaces copper sulfide/electrolyte (CuS/(CuSO4+H2SO4), Cu2S/H2SO4 and CuFeS2/H2SO4), based on studies of the overvoltage – time transients, will be presented. The transients were obtained using single pulse galvanostatic method and electrochemical cell with standard three electrode assembly. In that goal it was developed an original system for computer measurements that enables the application of several methods for electrochemical investigations (galvanostatic, potentiostatic, cyclic voltammetry, electrochemical impedance spectrometry etc). The system was tested and adjusted using commercial electrochemical equipment made by AMEL, Milano.In the first stage of consideration the different equivalent electrical circuits have been tested by computer programme OrCAD 9.2 in order to identify the circuit with responses equivalent in shape to experimentally obtained ones. In that way it was established a configuration of an analog electrical circuit for investigated electrochemical system. That phase enabled only very rough determination of values of circuit components and their relative ratio.In the second stage the method for determination of all elements of electrical analog circuit is described. It is based on mathematical consideration of a given circuit on one hand, and valves of the overvoltages at selected times, obtained from charging and discharging parts of galvanostatic transients, on the other."

Jan 1, 2003

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, CSIRO Minerals, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented."

Jan 1, 2003

By Johan F. W. Kock

"Hearing loss due to excessive noise exposure is the most prevalent industrial disease. It is ranked on the World Health Organization’s (WHO) priority list for major work related injuries. Uncontrolled noise not only has a physical effect, but is also a psychological hazard affecting the performance and well being of man. Noise induced hearing loss (NIHL) is irreversible, yet it is preventable. The first defence against noise (noise control engineering) is a high priority in the mining industry. Second defences should be a last resort when the engineering control of noise is inadequate. Hearing conservation programs and the use of conventional hearing protection devices seem to have failed in the prevention of noise induced hearing loss. If compensation payouts that quadrupled in the past ten years are used as a barometer for the success of existing hearing conservation programs, then new strategies and technologies need to be investigated. The best practice Hearing Protection Device (HPD) may be seen as the minimum standard for second defence noise control.Conventional hearing protection is widely applied, but also misused in the industry as well as in the mining sector. Empirical research results, ownership, general attitudes of workers as well as qualitative aspects will be explored. The paper provides reasons, evidence, case studies and strategies regarding the best practice hearing protection philosophy (the Noise Clipper Model) as implemented in the Implats Mining Group. Worldwide tendencies towards custom-made HPD’s, findings that indicate improvements in hearing conservation programs and finally the successful application of Custom-made Hearing Protection Devices, will be outlined."

Jan 1, 2003

By Mikhail I. Khersonskaya, Mark I. Mantsevich, Andrey V. Tarasov

"Due to depletion of the existing ore deposits the content of non-ferrous metals in produced ores has an inevitable tendency to decrease. Processing of low-grade ores is associated with production of low-grade selective concentrates and poses serious problems for the non-ferrous industry relating to increasing losses and expenses for waste treatment and disposal.The main component contaminating selective concentrates is iron sulphides.Copper-nickel, copper-zinc and polymetallic ores have been discussed as most important types of ores requiring removal of iron sulphides.One of the promising directions for development of selective flotation technology is the use of lowmolecular organic depressors. An advantage of organic compounds is in the possibility of multi-variant structure of organic molecules, which permits selection of a most efficient reagent for the given conditions. Another way for improving the grades of concentrates is concentration of valuable constituents associated with iron sulphides in an intermediate product and upgrading of the latter by chemical and metallurgical techniques.In order to remove iron from nickel concentrates, specific process conditions have been developed for selective flotation of pentlandite with the use of an organic depressor for pyrrhotite. The use of a depressor for flotation of high-grade copper-nickel ores ensures an increase in the nickel content up to 14% in the nickel concentrate produced as compared with 7% when using conventional process conditions, along with a nickel recovery improved by 2-3%."

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003