Search Documents

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By S. J. Ma

To look into the ionic release laws of the sulphide tailings in some copper mine, the effects of the soaking period, temperature, oscillating speed, and pH of the solution on the heavy metals ionic re-lease were investigated through static soaking leaching experiments. The results show that Cu2+, Zn2+, Pb2+, Cr3+ are of different leaching behaviors with soaking period. The ionic concentration in soaking solution for four ions has a great gap. Zn2+ is more easily released out of sulfide tailings than Cu2+, Pb2+, Cr3+ , and the ion release concentrations are not proportion to their contents in the tailings. The time for each ion to reach its maximum concentration are different. The minimum concentration do not occur at the first day. Each ion concentration shows different fluctuation characteristic during soaking process. Solution pH, oscillating speed, and temperature affect the releases of Cu2+, Zn2+, Pb2+, Cr3+ out of the tailings to different extent. The effect of pH value on ion re-lease for the four ions ranks as Zn2+>Cu2+>Pb2+>Cr3+, the oscillating speed ranks as Pb2+>Zn2+>Cu2+>Cr3+, and the temperature ranks as Cr3+>Pb2+>Zn2+>Cu2+.

Jan 1, 2014

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003

By N. Pradhan

In the Sukinda valley, Orissa, India, a large quantity of overburden material is generated during the mining of chromite mineral (on average 10 tons for every ton of ore). The overburden hereby depicted as ?lateritic nickel ore? contains on an average 0.5% Ni. IMMT Bhubaneswar is working on this material for extraction of nickel and cobalt. But for better recovery of metal values, thermal activation or thermal reduction of ore is required. An alternative biotechnological route for reduction of ore is hereby attempted. An anaerobic dissimilatory Iron (III) reducing bacterial consortium (here denoted as IRB), capable of imparting iron phase changes in the lateritic nickel ore was established which improves the subsequent extraction of co-precipitated Co (III) and Ni (II) from the ore. In this study, properties of thermally and microbially reduced lateritic nickel ore are compared vis-à-vis original ore. Due to the phase changes, original light brown color of the lateritic nickel ore changes to dark brown on IRB treatment. This dissimilatory reduction of ore leads to formation of some magnetic particles, which were separable by hand held magnet. Roasting and IRB treated ore on acid leaching with H2SO4 show about 45 % and 36 % leaching of nickel ore compared to about 18 % leaching from the original lateritic ore. If bacterial reduction method is successful, cost intensive method of ore roasting process can be eliminated. Thus, it is possible to make use of dissimilatory iron reducing bacteria for recovery of valuable metals from off grade iron ore/ laterites. Keywords: lateritic nickel ore, bacterial reduction, thermal reduction, dissimilatory fe (iii) reducing bacteria

Sep 1, 2012

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By Sharma K. K.

India is the third largest producer with accounting to fifth largest reserves base of coal in the world. Indian coal has high ash content (15-45%) and low calorific value. The basic processes being used in India at different places for coal washing adopts old techniques. Much of the valuable part is being lost during washing processes. With enhancement of the available techniques and use of new processes like flotation process indicates better recovery of carbon values during washing stage. The same will increase the reserve base, improve economy of operation and alleviate environment related problems. In the above backdrop this paper portrays the case study of an existing coal processing plant in India. The case study includes the modifications being incorporated in the existing process to enhance the product value. The existing practices and the future trend of process technology that could be adopted to meet the requirements in this country are also discussed. Keywords: washing, dense media cyclone, magnetite media, flotation

Sep 1, 2012

By S. K. Chaurasiya

o meet the ever increasing demand of iron oxide feed stock for rapidly growing domestic steel industries and to effectively manage the depleting reserve of high grade lumpy iron ore, Pelletization of iron ore fines/slimes are expected to play a dominant role in the near future. Use of pellets will also enable the blast furnace operator to achieve higher levels of productivity with lowering of operating cost. The effective utilization of Iron Ore Slimes is important not only from the point of view of optimum utilization of Iron values in the mined ore but also for preventing environmental pollution. A significant amount of slime is being accumulated at the tailing dam of one of the iron ore mines and with the present scale of operation the tailing dam will be filled in another 10 years. Hence to increase the life of tailing dam and for better utilization of the iron values a study has been carried out for the suitability of pellet manufacturing with slimes and fines at our laboratory. The pelletization studies are aimed for optimization of various parameters for production of Blast furnace/ DR grade pellets from beneficiated slimes and Fines. This paper attempts to describe the production of blast furnace grade pellets from beneficiated slime and fines and its characterizations.

Sep 1, 2012

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014

By D. Krawczykowski, D. Saramak, T. Gawenda

"Annual world zinc consumption is as high as nearly 14 millions of tonnes. Approximately 50% share of zinc is used for corrosion protection in processes of continuous galvanization and the hot dip processes. In the latter, two zinc containing residues are produced: zinc ash and hard zinc, which constitute around 10% each. Paper concerns the method of possible separation of metallic zinc from the non-metallic zinc compounds from the zinc ashes – the waste product of hot dip galvanization process. The investigative programme covered the comminution tests of the feed (zinc ash) in selected crushers: jaw crusher, roller crusher and impactor. Results of investigations show that application of individual crushing device results in various breakage of the feed sample. Impact force caused the highest increase in finest particles size fractions of the product, while metallic and non-metallic fractions were comminuted differently. The compression force, in turn, caused the selective comminution, i.e. the breakage of metallic zinc was observed in a higher degree. The presented approach appears to be an economical supplementary method of initial recovery of metallic zinc from metallurgical zinc waste. For the high demands for the zinc in the world and the need of corrosion protection, the method presented in the paper helps in more effective zinc recovery and environmental protection.INTRODUCTION AND METHODOLOGY World production of metallic zinc during last decade shows a slight increase and in recent years its consumptions reach 14 millions of tonnes. Figure 1 shows world production of zinc in the time period 2009 – 2016. Main directions of zinc utilization include: - Galvanization - Production of zinc alloys - Brass and bronze production - Semi-manufactures of zinc - Chemicals The major share in global zinc consumption constitute galvanization process (Bright 2007). Two main types of zinc galvanization are: hot-dip galvanizing (HDG) and electro-galvanizing."

Jan 1, 2018

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By S. V. Petrov

In recent years, heap leaching of gold is becoming wide spread due to low capital and operational costs that allows economically feasible processing of low-grade and cut-off grade ores. Currently, over 30 heap leach projects are operated in Russia. Some of the deposits treated by heap leach methods are almost depleted. Therefore, they will soon require spent heaps detoxification and reclamation. Traditionally, spent heaps are detoxified by chemical treatment. This process is characterized by relatively high kinetics and requires expensive reagents and additional equipment. The main disadvantage of this process is secondary contamination of the solutions by products of detoxification reactions and impurities contained in reagents. If there is enough time, spent heaps can be detoxified by natural degradation. The advantages of the proposed method are low operational costs due to use of existing heap leaching facilities and eliminating the need for chemicals for spent heaps detoxification. Residual concentrations of cyanides and thyocyanates in liquid phase (wet ore) of spent gold ore heaps after detoxification were 0.2~0.3 mg/L. Heavy metals were almost completely removed. The method was successfully used for detoxification of spent heaps at two gold mines.

Jan 1, 2014

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By M. P. Krasteva

The froth flotation process for separation of mineral ores depends on the establishment of care-fully controlled froth. The formation of very stable froth in the flotation circuit is a problem that may occur in many plants, resulting in down-time, low quality and grade of final product and considerable expenses. Froths build up on the top surfaces of thickeners, tanks and flotation cells until they overflow, or until the efficiency of the circuit is impaired. A similar problem exists in Assarel concentrator, Assarel-Medet PLC, Bulgaria. Copper and copper-pyrite ores are dressed in Assarel concentrator. They are characterized with variable and complex mineral and physical composition. During the flotation cycle, resilient and difficult to break-down froth is formed, which subsequently impedes the process of thickening and clear overflow obtaining. Due to this problem continuous sampling in the cycle of thickening was conducted. The mineralogical, chemical composition, particle size distribution and solid phase content of the products were determined. It was established that the solid phase of the froth build up on the top surface of the thickener differs considerably from this one of the thickener underflow. The data clearly indicates that a separation process takes place on the top surface of the thickener ? fine particles of chalcopyrite are concentrated in the froth. The role of chemical reagent addition in the break-down of the flotation froth is investigated in terms of surface chemical phenomena involved in the stabilized froths. Measurements of the coper minerals wettability and surface tension at the air/liquid interface were performed. The surface active agent AERODRI® dewatering aids were laboratory tested. Bench-scale froth collapse tests were conducted. Reagent addition into pulp-froth system promotes and leads to a bubble coalescence, an improvement of the wetting of the mineral particles and a decrease of the surface tension at the air/liquid interface. The results of the laboratory experiments showed that the presence of the surface active agent leads to considerably decrease of the froth stability and the destruction of the deleterious froths build up on the top surface of the thickeners in Assarel concentrator.

Jan 1, 2014

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By W. Kobal

The extraction of nickel (Ni) and cobalt (Co) from the laterite deposit of Ramu nickel-cobalt Project in Papua New Guinea was performed in this study. Chemical analysis by Inductively Coupled Plasma (ICP-AES) atomic emission spectrometer, SPS-3000 (Seiko Instruments (Inc.), shows the ore contains 48% Fe, 1% Ni, 0.1% Co, 1.8% Al, 0.14% Mg, and 0.8% Mn. Characterization by X-ray diffraction (XRD) analysis of the laterite ore obtained from the mine site shows the ore contains 70 to 80% goethite (FeOOH), assuming Fe content of 48% is mainly from geothite. The main leaching parameters investigated include; slurry temperature, leaching time and sulphuric acid (H2SO4) concentration to evaluate nickel and cobalt extraction. For all experiments, 10g batch samples are put into 300 ml beaker containing 100 ml of sulphuric acid of varying concentrations (1M, 2M, 4M). During the leaching period, 5 ml slurry samples are withdrawn at different times and filtered to obtain filtrate for ICP analysis to monitor nickel and cobalt extraction. Solid samples at the end of all tests are also obtained by filtration and after drying, XRD and ICP tests are performed to monitor nickel and cobalt contents. According to the test results performed at normal atmospheric pressure, over 99% of nickel and over 50% cobalt were extracted into solution within 120 min at 95ºC in 2M H2SO4 solution. Similar results were obtained when only temperature was reduced to 90ºC, but cobalt extraction increased to over 70% when leaching time was increased to 240 min. Further reduction in temperature to 80 and 60ºC resulted in reduction of nickel and cobalt extraction. At the end of each leaching test, magnetite was seen to attach to magnetic stirrer. The study showed nickel can be completely leached into solution but cobalt only up to 70%. Keywords: atmospheric pressure, sulphuric acid leaching, nickel laterite

Sep 1, 2012