Search Documents

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By Sergio Segovia Parra, Victor Hernan Sheen Uriol

This contribution of the concept of mass blasting both closing and production allows breaking paradigms, to limit the number of tons to thunder. The areas of geotechnical different mining large mining companies worldwide and especially from the National Copper Corporation (CODELCO, Chile) has been declining volumes closing blasting and production, with the misconception to protect the end walls of the pit, before any geotechnical risks caused by various types of faults; especially the circular faults. A blasting of small tonnage can do more damage to a wall when it is not properly sequenced, leading to the coupling of the wave train and therefore the exponential damage in/s (peak particle velocity, PPV) on the wall of the Tagus. Blasting closing mass production and contribute technically and operationally in the dynamics of the following operations: loading, hauling, crushing, processing and preparation of the final product; eliminating delays to return to thunder small volumes where one must stop all mine equipment, incurring high costs and especially losing valuable time in the continuity of the following unit activities.

Jan 1, 2015

By B. A. Cheeseman, R. Skaggs, C. F. Yen, S. Wolf

Shallow buried explosives pose a significant threat to lightweight vehicles and their onboard personnel. To date, designers of lightweight vehicles are limited in their knowledge of what occurs during the blast. The high intensity, short term loading imparted by the explosion is enormously complex and can be significantly affected by a number of parameters including the size, shape, type, detonation point and depth of burial (DOB) of the explosive and the type, density and water content of the soil. Recent advancements in numerical simulations have enabled the complex blast event to be accurately modeled by coupling Eulerian and Lagrangian analyses: the former is well suited to modeling the blast and while the latter, the structural response. Further validation of the modeling technique is considered in the current paper, which details simulations performed utilizing the coupled Eulerian-Lagrangian analysis to the study the blast output of explosives buried in saturated sand. These experiments varied explosive charge size, its depth of burial, the target stand-off (SO) distance and target plate dimension. The investigation concludes with a discussion of the accuracy of the numerical simulations when compared with the experimental observations.

Jan 1, 2005

By C. Feliciano, M. Cavalcante

A large iron ore open pit mine in Brazil operates with reduced blast sizes, due to the imminence of red alerts in the rainy season and the proximity of plant and dam structures that demand control of the maximum load of fired explosives. Blasts are currently not allowed to remain loaded with explosives due to the risk of red alerts, limiting mine operations close to them. There is a need to increase the blast sizes, reducing the number of events required to obtain the planned mass and, consequently, the unproductive operating hours lost with mine evacuations. The WebGen™ wireless electronic initiation system is a technology for firing detonators via lowfrequency magnetic induction that propagates through the medium, without physical connection. A blast was carried out with 406 holes divided into 4 panels, aiming to validate the preloading technique with wireless detonators and its performance in safety and productivity. The absence of lead wires in the system eliminates the risk of interaction between vehicles and detonator cables in stemming and loading operations, which can result in unplanned detonation or misfire. By eliminating the need for a spotter, it reduces people's exposure to dust and the risk of human-machine interaction. Furthermore, it eliminates the risk of unplanned detonation caused by lightning strikes. The pre-loading technique with wireless detonators enables flexibility and efficiency in planning through temporary accesses over loaded areas. In the demonstration, driving over the loaded area was essential to avoid jams and excessive wear on equipment due to the narrow berm and very friable material. Another gain in productivity was optimizing operational stages, since detonators were programmed in parallel with loading, anticipating process stages, in addition to eliminating the need to connect detonators. Considering the average handling and savings in downtime due to the reduction of blasting events, a potential increase in movement of 49,000t (54,013 short tons) in 3 months was estimated, keeping the vibration results within the required limit. The trial with wireless detonators demonstrated the feasibility of carrying out blasts with preloaded panels, without restrictions on the number of panels or detonators, enabling vibration control, innovating mine planning and increasing safety and productivity

Jan 1, 2024

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

By Catherine Johnson, Kelly Williams

The ability to measure the overpressure of a shock wave is necessary for explosives research such as shockwave focusing and field testing of blast-resistant designs for buildings and vehicles. To record the peak overpressure of the nearly instantaneous pressure rise at the shock front, pressure transducers with a fast response rate and streamline pencil design are needed. Time spent setting up sensors coupled with the expense of high-frequency data acquisition systems, and the inconvenience of low impedance cables can make the process challenging. Additionally, only small inaccuracies in sensor position can drastically change the measurement recorded. Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount. This paper investigates the accuracy of this method by setting dual transducer pencil probesat0and180 degrees perpendicular to the central axis of a285-gram(0.63-pound)cylindrical charge to record pressure versus time for comparison to the high-speed video. The axis of the camera lens is aligned with the central axis of the charge with both pencil probes in view. The pencil probes have two pressuretransducersset100millimeters (3.9 inches)apart to measure the time of arrival and are used to validate the velocities calculated from the high-speed images. This method can be used to evaluate the shock wave propagation from more complex prismatic charges with different cross-sectional shapes where precise placement of cumbersome pencil transducers in the near field is almost impossible.

By Thomas R. Scotese, John L. Ackerman

The Hanging Lake Tunnel Project represents a major portion of the Glenwood Canyon Project, the last piece of Interstate 70 to be constructed. The project features twin bore, large span rock tunnels and six open cut portal excavations, all excavated by drilling and blasting. This paper presents descriptions of the methods used by the Owner and Engineer to control and monitor the drilling and blasting practices in the tunnels and in the portal areas.

Jan 1, 1992

By R W. Givens

Comparison tests were performed on 6 emulsion concentrates, 3 microballoon sensitized emulsion concentrates, and 2 water gel concentrates from 8 different sources with ANFO used as a control standard. Variables measured include density, detonation, velocity, detonation pressure, calculated borehole pressure, viscosity, and lead cylinder deformation for blends of 15%, 30%, and 45% concentrate and AN/ANFO blends. Comparative results are presented for detonation velocity vs. deformation, and percentage of inherent air vs. deformation for these blends. It was hoped that these tests would serve as a tool to facilitate the comparison of different manufacturer's concentrates in AN/ANFO blends for equivalent performance characteristics and to help evaluate these products on an equal basis for bid solicitation purposes.

Jan 1, 1990

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining; on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years.

Jan 1, 1998

By Michael E. Curtis

This paper outlines a study performed to analyze the advantages of utilizing a blasting agent with a velocity of detonation that is 1.3 to 1.4 times the P-wave velocity of sedimentary shales and sandstones at a major Midwest coal operation.

Jan 1, 1997

By J. -P. Tshibangu, E. Lefebvre

ABSTRACT : The Tournai’s region in Belgium is characterized by outcrops of limestone that were mined out long ago by different companies for cement and crushed materials. The region is densely populated and the vibrations generated by blasts in the quarries are of big concern. The occurrence of electronic detonators and development of computer sciences brought a new expectation in controlling the vibration level and, hence, carry out bigger blast operations. In this paper we present the results of two experimental blast programs that have been carried out by the Nobel explosive Belgium Company on the Gaurain-Ramecroix quarry to understand the effect of the delay on the vibrations generated in the neighborhood. The first program has been implemented during the early use of electronic caps in Belgium (1996) by performing some unit shots. An attempt to model the effect of the production blasts by the hybrid method (Hinzen 1988) gave promising but poor results compared to infield measurements. A new program (more than ten blasts) has been implemented in 2006 in which the delay and blast firing sequence (i.e. the order in firing adjacent holes in a row) have been changed; a new attempt is made to build unit signals by deconvolution and then try to model production ones. A comparison of the two approaches is made.

Jan 1, 2008

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By R Holmberg, C Sjoberg, B Larsson

This paper describes the excavation of an underground naphta storage facility at Stenungsund in Sweden. The main purpose with this paper is to give an overall view of how the excavation was carried out and in what type of bedrock the storage was built. Emphasis has been done to highlight the importance of using cautious blasting to avoid blast damage in the remaining rock. Attempts has also been done in order to evaluate what the degree of Swedish cautious blasting has meant for the rock support costs during the construction period.

Jan 1, 1984