Search Documents

By Thomas P. Dowling

With the increased usage of AN/FO type blasting agents and the introduction and development of non cap sensitive slurries, water gels and other types of blasting agents, proper initiation and boostering of these insensitive materials has become a most important aspect of every blasting operation.

Jan 1, 1981

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

By Robert C. Friend

On-the-job and "hands-on" training programs which attempt to train newcomers to blasting with instructors whose only qualification is their experience can easily miss the boat. Organized training programs which utilize competent instructors and a well developed format are necessary if we wish to provide a meaningful program of instruction, But, let's not go overboard and attempt to provide a level of training which goes far beyond the scope of the worker's duties and responsibilities, and "need to know",

Jan 1, 1980

By Thomas E. Brown

With the ever increasing public sensitivity to our environment, the blasting industry can no longer be concerned with just drilling and blasting. Government regulations, augmented by public pressure, require that the industry must be more diligent in preventing spills, disposing of distressed products and packaging materials, controlling fumes and dust, preventing product contamination, developing environmental impact studies, and preventing unnecessary regulations. These liabilities in conjunction with those of vibration, air overpressure and flyrock will continue to greatly impact the industry.

Jan 1, 1995

By B H. A Brown

The components of passive laser survey systems and their relative functions are presented. A general outline of the capabilities and the information available are followed by two case histories. These involve the use of such systems in quarry blasts where loading adjustments and drilling designs were required. Their application in blast casting operations, stockpile measurement, surface and underground construction, and general surveying areas are briefly covered, with comments on the potential for demonstrating a return on an investment in laser survey equipment.

Jan 1, 1990

By Michail G. Egorov

As well as destruction and moving rock, the blast energy sets up a seismic wave in the ground and a shock wave in the air, which can present danger to buildings and disturbance to human occupants. This shock air wave potentially can cause to destruction of a window glass, the window and door frames and partitions of buildings. In modern buildings, distinguished with high flexibility, the shock air wave can cause to the intensive wall vibration, dangerous for these buildings.

Jan 1, 1996

By R W. Givens

This paper discusses emulsion performance and characteristics. Also presented are pattern design equations by a weight strength method, a "Q" factor method, and a coupled energy powder factor (CEPF) method. Pattern expansion by replacing ANFO with emulsion is presented along with quality control checks for emulsion products. The predicted performance of the calculated burden and the equivalent powder factor as a function of the emulsion percentage, as determined by the three methods, is compared. Field results indicate that of the three methods the weight strength is the moot conservative, the "Q" is overly optimistic, and the CEPF more accurately predicts the effect of coupling and is more consistent with a variety of emulsion and heavy ANFO products.

Jan 1, 1989

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By G J. Kulbieda

The Empire Mine initiated production in 1963. Since then the unit operations of drilling and blasting have evolved continually in order to meet the increased mining requirements demanded by plant expansions in 1968, 1973 and 1980. Additionally, advance mine planning has become an integral part of proper pit development and is necessary to insure uniform blending of the distinct ore horizons contained within the mine area. Blasting practices have been modified to facilitate the autogenous grinding system utilized at Empire and pioneered in the Iron Ore Industry. Technical innovations in the explosives industry, as well as, progress regarding on site blast engineering methods have substantially increased the use of ammonium nitrate explosives and helped to establish efficient charging procedures. In addition, the recent introduction and use of ammonium nitrate fueled with nitropropane and methanol indicates that it is a viable substitute for aluminized ANFO.

Jan 1, 1981

By Pierre Allard, Wilfrid Comeau

Near-field and close-in blasting can be safe and efficient, near engineered structures, if the dynamic reaction of structural members to blasting vibrations are considered. Safe particle velocity criteria can be derived from allowable safe static flexural deflections and critical frequencies. Control of close-in blasting can be accomplished using low-pass filtering of the particle velocity signal at the critical frequency. The CETE Mediterranee laboratory at Aix-en-Provence, France, a branch of the Ministry of Roads and Bridges has -pioneered this approach and successfully applied it to major road cuts and tunnels in built-up areas, as well as a major powerhouse expansion project in Africa. This approach is presently being used for a spillway rehabilitation project in Quebec, Canada. This paper exposes- the theoretical aspects and gives case histories of its use. The SCS-15 an automated, peak reading, data acquisition device is described.

Jan 1, 1991

By Carlos Agreda

The rock blasting environmental impacts such as: flyrock, groud vibrations,airblast,and/or noise, dust and fumes are identified and mentioned. Some comments on the correction factors that might be taken into consideration to calculate the initial velocity and the maximum projection of the rock fragments are mentioned as well.

Jan 1, 1995

By C F. Argo

In the past several years the "Kelly Bar", an innovative device, which incorporates borehole d-rifling and explosives loading into a single detail, has come under scrutiny and criticism. The practical aspects of the Kelly Bar procedure is not questioned, and the system has been highly successful in expediting the loading of explosives in difficult and unstable formations. There have been a number of accidents indirectly associated with Kelly Bar loading and the point in question has become one of safety rather than mechanical feasibility.

Jan 1, 1975

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Isaac E. "Chip" Harris

A general understanding is given to how and where blast hole drills are used and what recent developments have taken place with small and large diameter drill hole machines. Indications are that new developments with high penetration rates and large diameter holes are not necessarily the answer to increased production in the field.

Jan 1, 1979

By Zhang Shixun, Wang Xuguang, Wang Guoli

A massive millisecond blast at an open-pit mine of large scale can be realized by using the blasting technology of pre-loaded explosives, which can enlarge production scale, reduce the frequency of blasting and of large production equipment movement, and raise the production efficiency. The reason why application of this technology is restricted at high sulfide ore deposits of variable and complex geological conditions is that an exothermic reaction will take place when explosives contact sulfide ores, which could lead to accidents such as spontaneous burning and detonation of explosives pre-loaded in boreholes, influencing blasting and production safety. The thermal decomposition reactions of emulsion explosives of different prescriptions in contact with pyrite have been studied by differential thermal analysis (DTA), kinetics parameters calculation and accelerating rate calorimetry (ARC), and on the basis of the above studies, the safety of emulsion explosives used in sulfide mines has been evaluated with the safe contact time of different emulsion explosives with pyrite determined.

Jan 1, 1998

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By Yoshiharu Tanaka, Keita Morooka, Masaaki Yamamoto, Katsuhiko Kaneko

Smooth blasting is the standard method for underground rock excavation, to reduce over break and remaining rock damage. We already utilized the high accuracy of the electronic delay detonator to investigate its effect on over break remaining rock damage, and surface smoothness. And we presented at 11th annual symposium on Explosives and blasting Research.

Jan 1, 1998

By Jim Davis, Calvin J. Konya

The methods used to confine the gases within a borehole can influence the amount of useful energy obtained from the explosive charge. Improper confinement not only wastes energy and raises cost but also can result in airblast, excessive ground vibration, flyrock and boulders. The type of stemming material and amount of stemming used will definitely influence the degree of confinement and the efficiency of the blast. In order to extract the maximum energy from the expanding gases, the stemming plug should never blow out and allow the gases to escape prematurely.

Jan 1, 1978

By Joseph Trocino, John Anderson, Stephen Murray

This paper describes the development of LEXFOAM® (Liquid EXplosive FOAM) as a unique low density explosive, and its successful application as an effective tool for "in-place" demolition of landmines and unexploded ordnance. Explosives research using aerosol technology led to the development of LEXFOAM whose components are safely transported and stored as flammable liquids. These components are mixed on site to produce an explosive foam, which enhances safety and minimizes logistical problems. Hand-held, Backpack and Palletized Delivery Systems form a versatile family of dispensing systems to suit any application.

Jan 1, 1998

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978