Search Documents

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By William L. Crentz

This study of the preparation characteristics of the coals in Indiana County, Pa., is the second in a series of Bureau publications appraising the Nation's coking-coal reserves by counties and the practicability of upgrading marginal deposits to metallurgical standards. The first publication dealt with the preparation characteristics of the principal coal beds in Cambria County, Pa. Over 95 percent of the coal remaining in Indiana County is in the Upper Freeport, Lower Freeport, and Lower Kittanning beds. Isolated patches of Pittsburgh-bed coal are present, and the Upper Kittanning bed is found in minable thickness at some locations, but production from these sources is not large. The greatest production is from the Freeport beds, which account for nearly 70 percent of the Indiana County coal output. These beds usually contain two or more shale or hone partings and in many places are high in sulfur. The large proportion of bony coal in the Freeport beds 'produces a relatively high-ash product. Mining practices vary from place to place, but it is frequently necessary to leave certain bony portions of the bed in place in order to load a satisfactory product. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1951

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By H. C. Hamontre

The liquid-level gage described in this report is an instrument designed to locate liquid levels in wells rapidly and accurately and, with auxiliary equipment described, to follow moving liquid levels automatically. The depth at which the instrument makes contact with the liquid in a well is indicated at the surface by a depth meter on the cable to which the instrument is attached. When the gage is used to follow a surging moving level, the liquid depth is indicated continuously at the surface. This report contains a description and illustrations of the gage and outlines the operating procedures. The instrument is 1-3/4 inches in diameter and approximately 6 feet in length and may be operated through 2-inch tubing. The gage consists essentially of a float that moves upward with respect to the rest of the assembly, causing a change in the flow of electric current from the surface when the liquid level is reached. The instrument has been tested under a variety of conditions and has been found to be sensitive to changes in liquid level of 1/2 inch. Its accuracy is limited principally by the accuracy of the wire-line depth indicator used. It is not affected by pressure or temperature, and it can be run in open hole or under pressure through a lubricator. It employs only one electric circuit and can be run on an Amergraph single-conductor cable (type 1-H-0) ,

Jan 1, 1954

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By C. F. Jackson

This paper describing the mining practices at a mine in the Southeast Missouri district is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The conditions, operating methods, and practice described in the following pages arc those obtaining at a property in the Southeastern Missouri lead belt, St. Francois County, Mo. This property is the eldest in the county and is a consolidation of a number of separate mines originally opened up as individual operations many years ago. Present-day operations have necessarily to be adapted to suit the older levels, stones, and pillars, and also the recovery of ore from worked over areas which was considered too low grade to mine in the earlier days constitutes a different problem than that of development and mining in virgin ground.

Jan 1, 1929

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930

By S. H. Lorain

"INTRODUCTION The veins of the Clark Fork district have been mined on a small scale since 1913. In May 1943, the district was examined by an engineer 3/ of the Bureau of Mines with a view to possible exploration for larger ore deposits that might be of value to the war effort. The area adjacent to the Hope, Whitedelf, and Lawrence mines was re-examined 4/ December 27, 1943. As a result, the Bureau of Mines started exploratory operations in the district during the summer of 1944 which was continued until the late spring of 1946. This report presents the data obtained from the investigation.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project' as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts the preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1946

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By John H. Thompson

Recent studies ** at the Pittsburgh Experiment Station of the Bureau of Mines have revealed some interesting facts as to the probable behavior of steamed coke in the blast furnace . The literature on the chemistry of the blast furnace was tho roughly reviewed , and with this information in mind , the probable behavior of the coke sulphur in the blast furnace was deduced . Enough small - scale tests were conducted to furnish a check on most of the important deductions , and the conclusions derived therefrom accord with what is already known in regard to the forms of sulphur in coke , and fit in well with the general opinion concerning blast-furnace reactions .

Aug 1, 1923

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952