Search Documents

By P. L. Woolf

Blast furnace coal injection tests conducted by the Bureau of Mines in cooperation with a consortium of 22 steel companies in 1963-1964 are described. These tests were part of a program of extensive investigation of auxiliary fuel injection in the Bureau's experimental blast furnace located at Bruceton, PA. Seventeen coal tests are described on various coals ranging from anthracite to subbituminous. Factors affecting maximum rates of injection were studied. These included coal size, coal type, and oxygen enrichment. The effect of high sulfur content coal and the means to control metal sulfur were investigated. An epilogue briefly describing the commercial experience with coal injection from 1960 to the present has been included.

Jan 1, 1985

By Levent Ozdemir

The results of a laboratory research program aimed at the development of a water jet assisted drag bit cutting system for coal mine applications are presented. Two types of drag bits, a conical and a plow bit, were tested in a hard sandstone rock with jet pressures of up to 20,000 psi. Jet locations investigated were in-front and behind the bit. For each jet mounting location, three jet impingement distances with respect to bit tip were tested. The closest jet impingement location to bit tip was found most effective, providing the greatest force reductions on the bit. Overall, significant bit force reductions up to 50 percent were obtained with jet assist. Also observed was a drastic reduction in airborne dust when jets were employed.

Jan 1, 1986

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By D. Randolph Berry

Volume II contains appendices which explain and document the recommendations of Volume I. The following topics are covered: Appendix A Discussion of Recommended Guidelines Appendix B Worldwide Use of Oxygen Self-Rescuers Appendix C Hypothetical Use of Oxygen Self-Rescuers in Post-1972 Coal Mine Explosions and Fires Appendix D Vibration Testing of SCSRs Appendix E Testing of In-Service Chemical Oxygen SCSRs Appendix F Discussions with Representatives of Underground Coal Mining Appendix G Recommendations for SCSR Storage Containers Appendix H Example SCSR Storage Plans Appendix I Testing of In-Service Compressed Oxygen SCSRs Appendix J 30 CFR 75.1714, 30 Regulations Pertaining to Self-Rescuers

Jan 1, 1981

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By Bruce I. Thomas

The occurrence of tin-bearing gravels along Tozimoran Creek in central Alaska has been known for a number of years. In September 1944 the Bureau of Mines investigated an area approximately 1,000 feet long and 200 feet wide along Tozimoran Creek to deter-mine the cassiterite content of the stream gravels, which are about 4 feet deep and covered by 3 feet of overburden. Nine trenches and two shafts were excavated, from which samples of the underlying gravels were taken. This report contains a discussion of sampling methods and tables giving the results of analyses.

Jan 1, 1948

By D. Harrington

Advocates of health and safety in mining have found themselves confronted in recent years with what might appear to be contradictory procedures with regard to dust occurrence in mines and what appear to be suitable methods or measures to give the mines and mine workers a maximum measure of protection against dust. A concerted and relatively effective drive has been made to introduce rock dust into bituminous and lignitic coal mines to prevent or limit explosion and fire disasters, while an equally determined effort has been and is now being made to curb rock dust or to eliminate it from air in metal mines to prevent or at least limit the occurrence of miners' consumption and other diseases. Both procedures are logical even though the efforts appear to be of an opposing nature. While rock dusting has not been applied in coal mines nearly as universally or as effectively as could and should be done, nevertheless a careful analysis of the record of the past 10 years indicates that the amount of rock dusting that has been done has resulted in the saving of a minimum? of 200 lives annually certainly no small achievement. Largely but by no means wholly due to the use of rock dusting, the number of fatalities from explosions and fires in our coal mines in the last 4 years haw been reduced more than 75 percent as compared with the 4-year period 1911-15, the first years of the existence of the United States Bureau of Mines, which was brought into existence in 1910 largely to try to do something about reducing the disgracefully high fatality occurrence from explosion disasters in our coal mines. Hence, rock dusting has been given at least a. trial and has proved its effectiveness definitely.

Jan 1, 1937

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By T. L. Turner, Daniel T. Rogers

As part of a program to investigate technology for the extraction of studied HNO3 alumina from abundant domestic ores , the Bureau of Mines leaching of calcined Georgia kaolinitic clay . In this investigation , iron impurities were removed from the aluminum nitrate pregnant leach liquor by solvent extraction , and the purified liquor was evaporated to prepare a suitably concentrated crystallizer feed liquor . Aluminum nitrate nonahydrate was crystallized from the liquor to separate the aluminum from undesirable trace elements and excess water . Continuous crystallization at 40 ° C in a pilot plant vacuum evaporative unit was performed for 5 days to observe the effects of impurity buildup under minimum bleed- stream conditions . Liquor feed rate was 26 lb/h and AAll (( NNOO33 )) 33..99HH22O0 ((AANNNN)) crystal production rate was 17 lb/h . Fe 203 and Cr203 were not effectively separated from the crystals , and P205 , MgO , and K20 impurities must be removed by recrystallization . Other impurities did not excessively contaminate the crystals . Washing the crystals with water or aqueous HNO3 gave an equivalent increase in crystal purity levels by displacing mother liquor . Theoretical equations , applicable to any continuous evaporative crystallization of developed to produce material balances for engineering ANN , were applications .

Jan 1, 1965

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By Barry Beith

This report details a study which was designed to assess the effect of retroreflective material on detection and form recognition of workers in the mining environment. Further, the study attempted to determine an optimal configuration of retroreflective material with respect to amount and placement on the body to facilitate detection and form recognition. The study involved a one-fifth scale simulation of the perceptual task found in the underground low seam coal mine. Four different configurations of reflective material were presented in various body positions, common to low coal miners, at three different locations in the visual field, i.e., 10, 25, and 45 degrees from focal line-of-sight. All reflective configurations significantly improve detection and form recognition over configuration (cap only) worn by miners. As the amount of reflective material increased, accuracy also tended to increase. Based on the configurations investigated by this study, the Armband configuration (i.e., refectorized armbands, belt, self-rescuer and battery pack) was determined to be optimum. It is recommended that an actual field evaluation be made using the Armband configuration to establish if simulator results are generalizable to the underground mining environment.

Jan 1, 1980