Search Documents

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By Robert C. Dyni

This report details the investigation of multiple-seam longwall subsidence conducted by the U.S. Bureau of Mines from 1978 to 1989. A field investigation monitored ground surface movements over four upper-seam longwall panels and six lower-seam panels. The characteristics of the subsidence occurring as a result of mining these panels are examined; in particular, the angle of draw, subsidence development, total magnitude and areal extent, and critical width are evaluated and discussed. Comparisons are also made between the characteristics of multiple-seam longwall subsidence and single-seam longwall subsidence that occurred at the same site.

Jan 1, 1991

By C. Daniel Kealy

Finite-element,, mathematical models that solve LaPlace's and Richard's equations numerically were used to locate the phreatic surface within tailings pond embankments and to define the subsurface flow of water from the pond. Both must be known to design structurally and environmentally safe tailings dams. The permeability distribution within and beneath the embankment, the fluid potential values upgradient and downgradient from the embankment, and the geometry and elevation of an approximately impermeable layer at some depth beneath the embankment were used as computer inputs in analyzing over a dozen finite-element models of tailings dams varying structurally from simple to complex. Results predicted with the finite-element model were confirmed with measurements in a laboratory model of a tailings pond and in the field. Of particular importance to the design of safe slopes, all data indicated that the phreatic surface within a tailings dam is concave upward, a configuration opposite that in most earth dams. The close correlation between predicted and experimental values confirmed the practicability of using the finite-element technique to design safe tailings dams.

Jan 1, 1971

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By Nicholls Harry R.

The Bureau of Mines studied the effect of varying the, diameter of explosive charges on the generation and propagation of strain waves. The parameters compared were strain amplitude, impulse, energy, and pulse shape. Three different explosives were detonated in three different charge diameters. Charges of cast 50/50 pentolite-detonated at the same velocity in 5-, 2.5-, and 1.5-inch diameters. Charges of ammonium nitrate-fuel oil prills and 45-percent semigelatin dynamite showed a strong detonation rate-diameter dependency. Detonation of these two explosives was considered nonideal. Differences in the diameter of the charge caused less difference in the strain-generating abilities of pentolite than in those of the other two explosives. This was also true for impulse and energy. Rise and fall times of the strain pulses for all three explosives were proportional to detonation time and cavity volume, respectively.

Jan 1, 1966

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By Richard S. Gaps

In 1983 the U.S. Bureau of Mines conducted a mineral survey of the Golden Valley Wilderness Study Area (WSA), CDCA-170. The 29,887 acre WSA, located in the western Mojave Desert near Ridgecrest, California, is underlain by pre-Tertiary plutonic rocks and volcanic and sedimentary rocks ranging in age from Miocene (?) or Lower Pliocene (?) through Pleistocene and Recent. No mines were operating in the WSA in 1983, nor is any mineral production known to have come from the WSA. Two mining claim blocks, portions of which are within the WSA, and seven isolated prospects, four inside the USA, were examined and sampled. No mineral resources were identified. Widespread propylitic alteration, with localized argillic and alunitic alteration, occurs along the southern boundary of the study area. Samples from claims and prospects within the altered zones are anomalous in gold, silver and arsenic, and some contain antimony, tungsten and mercury, indicating gold resources may exist. Alluvial sample results suggest recent claims in the northwest corner of the study area may also have gold resources. Portions of the study area are within the Randsburg Known Geothermal Resource Area while other segments are considered prospectively valuable for oil and gas and for sodium.

Jan 1, 1985

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Frank A. Peters

This evaluation of the sulfurous acid process for the production of metallurgical-grade alumina is the first of a series concerning various known methods of extracting alumina from low-grade aluminous materials and was undertaken to permit comparison with other processes. In the process with which this Bureau of Mines report is concerned, calcined clay is leached under pressure with 20 percent sulfurous acid and then filtered to remove a siliceous residue. The aluminum sulfite remaining in the filtrate is precipitated as a monobasic sulfite which, together with iron sulfite, is then decomposed under pressure to form a crude alumina hydrate and iron oxide. This intermediate product is purified in a modified Bayer process to yield alumina suitable for electrolytic reduction to aluminum. A study estimate (16)3 is used for these evaluations. The capital cost, not including land, is estimated at $95,701,600 on a Marshall and Stevens index basis of 240.0 for a plant producing 1,000 tons a day of alumina or 350,000 tons a year. The annual operating cost for this size plant is estimated at $22,831,100 or $65.23 per ton of alumina using clay at $1 per ton. Depreciation and local taxes are included in the estimate, but profit and Federal taxes are not considered.

Jan 1, 1962