Search Documents

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By A. M. Dale, J. Standeven, B. Evanoff

We encountered several areas of methodologic uncertainty during development of a data collection method for use with vibrating hand tools in metal assembly. A local manufacturer sought our assistance designing a data collection method for evaluating and predicting risks of upper extremity disorders associated with use of vibrating hand tools. Current methods of vibration measurement are described in ISO 5349 [2]. However, the complexity of measuring vibration along with other exposures such as force and posture has limited the number of workplace-based studies of upper extremity disorders that have included direct measurements of vibration. Data from this preliminary study was used to look at two issues: a comparison of vibration values between production and non-production workers when performing the same task, and a comparison of worker ratings of vibration comfort to direct measurement of tool vibration. Methods Eight experienced production workers used each of six metal fastening tools to install fasteners. Vibration was collected by 3 tri-axial accelerometers, one attached to the tool handle following ISO 5349 recommended locations, one attached to the hand dorsum on the 3rd knuckle and one to the thumb side of the wrist. Data sampling rate was 10,000 samples/second. Hand grip and feed forces were obtained using a Novel pressure sensing mat on the palm. Each trial consisted of installing 10 fasteners per tool for each of the 6 tools. The test set-up placed the wrist in the position typically used by the operator during production. Each worker documented subjective comfort and effort ratings on a seven point scale following each series of fastener installations. One series of testing was completed by three non-production workers inexperienced in fastener installation to simulate use of alternative employees for data gathering. Vibration data for each trial were acquired, digitized, and stored using Lab View. The X, Y, & Z axes were used to calculate the vector sum response for each tri-axial accelerometer. The tool data were digitally filtered following ISO recommendations. Calculated data consisted of the mean RMS over the tool’s on- time, the starting and breaking peak impulses, and the peak of the frequency response. Results Production workers (n=8) were right hand dominant males with a mean age of 55 years and normal hand strength (mean right grip = 106 lbs). Non-production workers (n=3) had similar characteristics. We found large and statistically meaningful differences in hand force during tool use between production and non-production workers (mean production workers = 9.77 lbs, mean non-production workers = 43.30 lbs, p = 0.0001). Vibration values obtained from the hand also showed a statistically meaningful difference (mean in production workers = 0.67 Gs, mean in non-production workers = 1.48Gs, p = 0.0014, figure 1). Experienced worker ratings of comfort during tool use demonstrated a moderate correlation with measured vibration (r=0.63). Worker ratings trended with direct recordings from the tool handle as shown in figure 2.

Jan 6, 2006

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By Raymond W. Hiteshue, Henry H. Ginsberg, Paul S. Lewis

Coal was gasified in the presence of up to 3.57 million roentgens of gamma rays by the Bureau of Mines to determine whether the irradiation increased the gasification rate or yields of methane and hydrogen . High volatile A bituminous coal was gasified with steam at 500 and 1,500 psig and temperatures of 1,400 ° and 1,800 ° F ; five other coals ranging in rank from lignite to anthracite were gasified at 500 psig and 1,800 ° F. The average results of replicate experiments with and without radiation were compared for possible effects of radiation from 40,000 curies of radioactive cobalt . The irradiation had no gross effect on the gasification rate or on the yield and distribution of methane and hydrogen . It was concluded that gammaray irradiation produced no improvement in the technology or economics of coal gasification .

Jan 1, 1964

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

To provide an engineering solution to wood crib design and deployment strategies that will ensure safety for underground coal mine workers. This is accomplished by preserving necessary ground control requirements while minimizing support costs or by developing new support strategies to enhance ground support in difficult conditions. A secondary objective is to be able to quantify wood crib support performance to define support requirements for alternative support systems. These objectives have been achieved through a simple-to-use computer program called the wood crib performance model (wcpm).

Jan 1, 1997

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the &apos;indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Charles B. Carpenter

In general terminology, the West Texas Permian Basin companies the area south of the Texas Panhandle and west of the Bend Arch or Central Basin region. It is outlined more definitely by geologists however, as that area underlain by the south half of the Permian Salt Basin4/ and includes Scurry, Mitchell, Sterling, Howard, Glasscock, Reagan, Crockett, Upton, Midland, Martin, Gaines, Andrews, rotor, Crane, Pecos, Ward, Winkler, and Loving Counties in Texas, and.. Lea and Eddy Counties in New Mexico. The oil fields of the area, of which more than 70 have been discovered, are shown in fire 1. Approximately 4,200 producing oil wells have been drilled in these fields. Oil has been produced from limestones and dolomites of Permian age in most of the fields in the West Texas Permian Basin. Some of the fields produced oil from sandstone beds above the limestone, and in two fields production has been found below the limestone in formations of Ordovician age.

Jan 1, 1936

By William G. Pariseau

Elastic-plastic finite-element simulation of cut-and-fill stoping in deep, narrow veins shows substantial quantitative agreement with field measurements of stope closure and fill pressure made at two mines in the Coeur d&apos;Alene mining district of northern Idaho. The simulation procedure, validated by field data, was used in an analytical study of vein-wall closure and sill-pillar stress as influenced by fill modulus, rock modulus, and premining stress. Ratios of closure and pillar stress in the filled stopes to closure and pillar stress in the unfilled stopes are used as prediction indices for fill performance. In general, the support capability of fill increases dramatically as the ratio of fill modulus to rock modulus approaches 1. A significant reduction in closure .from the open stope--up to 75 percent--occurs with a relatively low-quality 10-ksi-modulus fill (rock modulus of 1,000 ksi). However, a higher quality fill is needed to achieve a substantial reduction in pillar stress from that of the open stope. A 100-ksi-modulus fill reduces pillar stress in both the 36-foot and l6-foot pillars (vein width is 10 feet) by about 50 percent relative to the open stope.

Jan 1, 1976

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

By Charles B. Carpenter

In general terminology, the West Texas Permian Basin comprises the area south of the Texas Panhandle and west of the Bend Arch or Central Basin region. It is outlined mere definitely by geologists, however, as that area underlain by the south half of the Permian Salt Basin4/ and includes Scurry, Mitchell, Sterling, Howard, Glasscock, Reagan, Crockett, Upton, Midland, Martin, Gaines, Andrews, Ector, Crane, Pecos, Ward, Winkler, and Loving Counties in Texas, and Lea and Eddy Counties in New Mexico. The oil fields of the area, of which more than 70 have been discovered, are shown in fire 1. Approximately 4,200 producing oil wells have been drilled in these fields. Oil has been produced from limestones and dolomites of Permian age in most of the fields in the West Texas Permian Basin. Some of the fields produced oil from sandstone beds above the limestone, and in two fields production has been found below the limestone in formations of Ordovician age.

Jan 1, 1936

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By K. C. Dean

Horizontal and vertical air classification systems were tested individually and in simulated tandem use for the recovery of ferrous and nonferrous metals and of other noncombustible and combustible products from shredded urban refuse. The horizontal air system with a larger tonnage throughput was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Air elutriation, magnetic separation, and screening of shredded minus 6-inch municipal refuse recovered 92 percent of the metal in a relatively clean iron product contaminated only by adhering coatings or entrapped materials, recovered 97 percent of the combustibles in a 97-percent combustible product, and rejected 88 percent of the nonmetal noncombustibles. Cleaning of the preliminary combustible fraction produced a 98-percent paper product while rejecting other combustibles (plastics, rubber, textiles, etc.) into a 94-percent combustible product. Retreatment of the preliminary noncombustible fraction produced a relatively clean glass product.

Jan 1, 1971

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state. Adsorbed gas is stored in the micropore structure and its transport is governed by Fick&apos;s law. The free gas occurs in the fracture system and flows according to Darcy&apos;s law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds

May 1, 1969

By H .. B. HUMPHREY, F. E. Cash

Sixty-one fatal accidents were reported in the mines of Alabama during 1930. This number is a decrease of 15 per cent as compared with 1929; however, production was 13 per cent and the man-hours worked were 16 per cent less than in the previous year. There were 21,731 men employed inside and 3,386 outside. Table 1 gives the comparative rates per million tons and per million man-hours for the United States and for Alabama for 1929 and 1930. These rates are based on figures published by the State and by the United States Bureau of Mines, with preliminary figures for 1930. (These sources of data are used throughout this paper.)

Oct 1, 1931

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989