Search Documents

The Federal Mine Safety and Health Act of 1977* defines respirable dust as dust measured with a device approved by the Secretary of Labor and the Secretary of Health and Human Services [30 USC 842(e)]. The approved sampler for respirable coal mine dust is the coal mine dust personal sampler unit (CPSU) [30 CFR 74; Jacobson 1971; Jacobson and Lamonica 1969]. The CPSU is generally called the 10-mm nylon cyclone, although the 10-mm nylon cyclone is actually just one component of the CPSU. The CPSU may either be mounted on a worker (with the sampling head positioned in the breathing zone for personal exposure monitoring) or in a fixed location for area sampling [Tomb 1990]. The CPSU consists of a pump unit, a sampling head assembly, and a battery charger if rechargeable batteries are used in the pump unit [30 CFR 74.2]. The sampling head assembly contains two stages. The first stage is a 10-mm nylon cyclone, which has collection characteristics similar to an elutriator. The amount of dust penetration depends on the flow rate [Jacobson and Lamonica 1969]. The second stage is a membrane filter (vinyl, pore size 5 pm) that collects the dust passing through the cyclone. The dust collected on the membrane filter is weighed to a precision (standard deviation) of 81 pg [Parobeck et al. 1981], and the respirable dust concentration in the mine atmosphere is then determined from the mass of dust collected and the volume of air sampled [Tomb 1990].

Jan 1, 1997

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By Stephen R. Wilson

The West Tintic mining district is located at the southern end of the Sheeprock Range in Juab County, Utah (fig. 1). Scheelite was discovered in the area during 1940, and the Desert Tungsten Co. began mining in May 1942. The ore was shipped to the Metals Reserve Co. chemical treatment plant at Salt Lake City during the war. A Bureau of Mines development project was established on property controlled by the Desert Tungsten Co. Work was started during September 1942 and completed in February 1943. The program included removal of overburden in the mine area to facilitate geologic napping, followed by surface trenching, diamond drilling, and sampling (figs. 2,. 3, 4, and 5). Eleven diamond-drill holes totaling 1,480 feet were drilled from the surface. Sixty-one samples from the surface trenches and diamond drill holes were assayed. The logs of the holes are given in table 2. Assay results of samples from the surface trenches and diamond drill holes are listed in tables 1 and 3. Geologists of the U.S. Geological Survey mapped the mineralized area during the project period. The scheelite deposits occur in limestone areas adjacent to intrusive m9.sses, which are principally monzonite. The ore bodies are pyrometasomatic in origin, but consist of two somewhat different types: (1) a series of veins occupying fault zones in limestone and (2) tactite bodies immediately adjacent to the limestone. The veins in the limestone have been the most productive of the two types.

Jan 1, 1950

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By David E. Siskind

The Bureau of Mines recorded particle accelerations in the mine roof produced by three types of explosives in the Pilot Knob Pellet Co. mine, Pilot Knob, Mo. Examined were the effectiveness of cube root, square root, and two-thirds power scaling in grouping the underground blast vibration data, and the effects of mine geometry, rock type, explosive type, and charge size on blast vibration levels. A propagation law for this mine was determined. The scaling factor of the square root of the charge weight was developed from previous Bureau studies of vibrations from quarry blasts, and in under-ground blasting both square root and cube root scaling were found applicable for scaling particle vibration data. The vibrations from the Pilot Knob blasts were best grouped by a square-root scaling factor. The empirical propagation equation AW1/2 = 76,250 (R/W1/2)-2.61 where A is the peak acceleration in g's, W is the charge weight in pounds, and R is the distance from the blast in feet, may be used to describe vibration amplitudes from charges fired with zero delay caps or with a single cap at Pilot Knob. Statistically significant differences were found in the vibration levels generated by the different explosives. The Power Primer (75-percent weight-strength ammonia gelatin dynamite) produced levels of vibration of 1.7 to 2.4 times those of AN-FO and slurry explosives; the latter two are approximately equal.

Jan 1, 1973

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By E. W. Dean

In the early winter of 1919 the Pittsburgh petroleum laboratory of the Bureau of Mines undertook the work of testing fuel oil samples representing purchases of the United State Shipping Board for ships sailing from the port of New York. fuel oil was, at this time, being bought on a contract which involved specifications issued by the United States Navy under dace of October 2, 1920 (See Bulletin 1, Oil Division, U. S. Fuel Administration.)The object of the Bureau of Mines in undertaking this inspection work was twofold. (1) The Bureau was in position to give, and the Shipping Board needed, reliable laboratory service for checking the quality of the fuel oil purchased, the value of which ran into millions of dollars for,year's supply. (2) It was believed, and later demonstrated, that the existing specifications did not insure the obtaining of a reliably satisfactory quality of oil.The objection to the specifications concerned the employment of a clause limiting the gravity of the oil. The inadequacy of gravity specifications for several types of petroleum products has long been recognized, and there was every reason to reason to believe that they were no more desirable for fuel oil than for gasoline, kerosene, or lubricating oil. A first and obvious objection was the fact that it is somewhat difficult to make accurate gravity tests on ""heavy"" residuum fuel oils. (The Bureau found it necessary to employ or such tests a rather tedious procedure involving the use of a picnometer and an accurate balance, as the simpler methods, employing hydrometer or displacement balance, proved unreliable in a large proportion of cases.) A second and more important objection was that gravity tests, even when accurately made, do not provide a reliable index of the actual quality of the oil.

Feb 1, 1921

By Charles Seitz

The Bureau of Mines has modified its parts-per-billion helium-4 analyzer to improve the analytical capabilities of the instrument. The modifications resulted in the following improvements: (1) The analytical precision of the instrument for 10 consecutive analyses was improved to ±1 ppb at the 5,000-ppb helium-4 level, (2) the helium-4 sensitivity was increased almost tenfold, and (3) the minimum detectable limit for helium-4 was improved to 0.5 ppb. The modifications made to improve the instrument included replacing the ion-source control circuit with a direct-current solid-state design, controlling the temperature of the ion source, stabilizing and reducing the pumping rate of the vacuum system, and optimizing peak integration.

Jan 1, 1986

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By B. I. Ferber

Toxic and explosive atmospheres are discussed, along with some of the instruments commercially available for their detection. No attempt has been made to evaluate the accuracy of anyone device. This circular has been prepared primarily to aid mine inspectors in selecting suitable instruments for underground gas detection.

Jan 1, 1972

By N. F. Le] [Jaune

[ ]

Jan 1, 1923

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By Hylton R. Brown

This publication, an abstract of a progress report covering an investigation of hazards in thermal coal-drying plants has been prepared according to the suggestions and recommendations of a committee6/ appointed by J. J. Forbes, Director of the Bureau of Mines, when the original report was reviewed at a meeting of representatives of the mining industry, operators of coal-drying plants, coal-mine workers, and the Bureau in Washington on May 6, 1955. The investigation on which the report is based was made in accordance with action taken at a previous conference in Washington on May 19, 1954, called by Director Forbes to consider what should be done to prevent explosions and fires in coal-drying plants. Scope of Investigation The investigation was planned to obtain information considered essential for properly appraising fire and explosion hazards in different types of coal driers. A questionnaire sent to Bureau personnel provided preliminary information on coal-drying facilities at more than 270 preparation plants. Information on methods used in operating different types of driers, with their furnaces, fans, cyclones, and other auxiliary equipment, was obtained by personal visits or conferences with the operators at 13 plants. Factual data on operating temperatures, composition of the drying gases, air flow, dust loading of the air or gas currents, use of water sprays, auxiliary air controls, and other factors were obtained by conducting full-scale tests at six different plants and making laboratory investigations with samples of dust and gas collected during the tests.

Jan 1, 1956

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By John L. Morning

Although faced with a slowdown in the world economy, continued inflation, and rising costs, the mining industry exceeded its 1974 raw mineral production value of $55.1 billion by 13%. The increase was due to value increases in the production of fuels and nonmetals; metals reported a decrease in value. Of 23 metals produced, 14 showed value increases; of 44 non-metals produced, 26 reported value in-creases. Because of increasing costs and depletion of high-grade reserves, the mining industry continued to rely on new technologies to maintain its profit margins. In the surface mining sector, the development of new tools and equipment played a large part in increasing production and maintaining this goal. Some of the types of equipment developed were instrumentation for control of pit slope stability, shovel power transmissions, electric wheel trucks, and single-flight conveyor systems.

Jan 1, 1977

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920