Search Documents

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By Horace C. Porter, F. K. OVITZ

The various fuel investigations that were being carried on by the technologic branch of the United States Geological Survey were transferred by law on July 1, 1910, to a new federal bureau, the Bureau of Mines, that was authorized to continue the investigations and make public reports of the results. In consequence of this transfer, the following report is published as a bulletin of the new bureau. The United States Geological Survey had been engaged in analyzing and testing coals, lignites, and other mineral fuel substances under authority given by act of Congress. This work, now centered at the experiment station at Pittsburg, Pa., had its beginning in the operations of the coal-testing plant erected at the Louisiana Purchase Exposition in St. Louis, Mo., in 1904. The results obtained at that plant showed that the work of determining the fuel value of the coals and lignites in the United States with a view to increasing efficiency in their utilization would be incomplete if it did not include systematic physical and chemical researches into the processes of combustion. Hence in its later investigations the Survey carried on such re- searches, concentrating attention on those lines of inquiry which promised results of greatest economic importance. This bulletin is a report on an investigation of the volatile matter in several typical coals-its composition and amount at different tem- peratures of volatilization. As the investigation is still in progress and will doubtless include other coals than those already examined, the bulletin may be considered a preliminary report, stating the prob- lems studied, the methods used, and the results thus far obtained.

Jan 1, 1910

By F. D. DeVaney

An examination of the physical properties of manganese ores is being made at the Mississippi. Valley Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Missouri. The object of the study is to find out how much these ores can be beneficiated by such processes as jigging, tabling, magnetic separation, and flotation. Some. of the results were given in an earlier report.4 Eighty samples obtained from various prospects and mines throughout the country have been examined; this is a very small part of those that should be examined before the work can be a definite factor in-the appraisal of manganese ores or the guide in beneficiation which the operators seek. The ore deposits are not expected to reach to great depths vertically, after the manner of copper and gold, but in lateral distribution their greater extent is notable. This applies particularly to the residual and replacement deposits of manganese.

Jan 1, 1929

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By J. Douglas Causey

No mines are active in the Hunter Mountain Wilderness Study Area (WSA), and no mineral resources have been identified in the WSA. However, the Monarch Mine has low potential for silver, copper, tungsten, and gold resources in quartz veins; the Shirley Ann Group and Sal Group have moderate and low potential, respectively, for silver, lead, and copper resources in skarn; claims overlying the Eureka Quartzite have low potential for silica resources; and the Tourmaline N1-4 Prospect has low potential for tourmaline resources in quartz monzonite. Copper, lead, silver, tungsten, molybdenum, wollastonite and garnet occur in skarn zones between monzonitic and carbonate units. Silver, tungsten, and copper also occur in quartz veins within monzonite. Known metallic mineral deposits are small, erratic and discontinuous. The J. 0. Mine, adjacent to the northeast corner of the WSA, may contain as much as 26 million tons of subeconomic wollastonite resources. The crest of an open pit to produce that resource would extend into the WSA. No information exists on geothermal potential because no exploration has been done in the area. No occurrences of energy minerals are known within the WSA.

Jan 1, 1983

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By F. D. Stevenson

Thermodynamic properties of metal halides and, in particular, vapor pressures have become of great importance in recent years owing to increased application of chemical processing to extraction of metals from their ores. Vapor pressure data serve not only as a valuable source of latent heat of vaporization and fusion values but also differences in metal-halide vapor pressures often provide the basis for their separation by conventional mass transfer operations. This literature search was made to provide a ready reference to experimental vapor-pressure data of metal halides and oxyhalides. Results are reported in two main sections: (1) A tabulation of vapor- pressure references for each of the metal halides (listed by metal) for which actual experimental data are reported (table 1), and (2) a bibliography of the citations. Metal halides and oxyhalides are listed by chemical formula and chemical name, based on the stock4 system. To facilitate location of the references, a listing of the journal titles and their abbreviations follows the bibliography.

Jan 1, 1963

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By A. T. Coumbe

The first survey 3/ covering sales of liquefied petroleum gases was made in 1930 by the Bureau of Mines, which at the time was under the United States Department of Commerce. This original canvass covered national totals for 1922 through 1929, and most of the supply came from natural gasoline plants. The 1930 report showed approximate totals for butane and propane and for butane-propane mixtures and pentane grouped together. No attempt was made to breakdown the national sales by various uses until 1931, when the quantities for domestic or household consumption, gas manufacturing, and industrial requirements, including miscellaneous uses were indicated. As the market for these liquid petroleum gases expanded and as new uses came into importance, their respective quantities were shown separately in the annual survey. Sales for internal-combustion engine fuel and for raw material for chemical plants were first taken out of the industrial total in 1936. During World War II liquefied petroleum gases became important as feed stock diverted to synthetic rubber plants, and consequently the survey was broadened to cover this particular demand, beginning in 1944. Pentane was dropped from the survey after 1943, as, being liquid at atmospheric pressure, it is not considered as one of the liquefied petroleum gases and furthermore, the quantity reported made up less than 1 percent of the total sales. Thirteen producing companies reported to the Bureau in the first survey made in 1930, and in the 1952 canvass about 130 producers--petroleum refiners and natural gasoline companies--and about 1,300 dealers cooperated by filing schedules showing a breakdown of their sales. Their 1952 deliveries of approximately 4.5 billion gallons of liquefied petroleum gases were equivalent to about 3.4 billion gallons of gasoline or 3.1 billion gallons of distillate fuel oil.

Jan 1, 1954

By G. L. Oldright

This paper is the first of a series that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. ACKNOWLEDGMENTS The writers wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, to Mr. J. O. Elton, the general manager, and to Mr. A. B. Young, his assistant, for their broad-gauge policy that has made possible the securing and publishing of these data. For the staff at Tooele, acknowledgments are made to Messrs. B. L. Sackett, general superintendent, Carlos Bardwell, assistant general superintendent, S. Jacobsen, blast-furnace superintendent, H. M. Rockwell, assistant blast furnace superintendent, and J. O. Welsh, superintendent of the general research, for the spirit of cooperation they manifested in carrying out this work. Mr. C. Reish, a member of the research department, was detailed by, the company to assist in this' work and his whole-hearted assistance has been found invaluable.

Jan 1, 1929

To design an apparatus that advances the state of the art in gas content testing equipment. The goal of the design is to incorporate improvements in testing sensitivity/accuracy, durability, and ease of operation over existing equipment. It is also desirable for the new design to successfully perform gas content determinations of multiple chemical species from a rock sample.

Jan 1, 1999

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By J. V. Scalera

Because of U.S. dependency on imported critical metals, the Bureau of Mines has conducted research to evaluate the possible substitution of nitrided low-alloy steels for higher chromium-containing alloys. The corrosion data for nitrided steels are limited primarily to the Soviet literature. The objective of this study was to determine the corrosion properties of six commercially nitrided low-alloy steels in a 5-wt % NaCl solution at pH 4. Weight-loss tests indicated that, in deaerated test solutions, most of the nitrided steels were less corrosion resist-ant than nontreated steels. However, electrochemical tests indicated that under more oxidizing conditions, nitrided materials are converted to a passive state with a significantly reduced corrosion rate. Elec-trochemical tests performed in an aerated environment confirmed the passivity of the samples in an oxidizing environment.

Jan 1, 1984

By Thomas C. Denton

ALL of the 45 political divisions of Africa were accessible to non-Communist world industry and commerce throughout 1964, although in some of them revolt and political attitudes presented problems. The position of the continent as a whole for mineral and mineral fuel resources, production, and oversea exports continued to improve. At yearend, significant quantities of a greater number of mineral commodities vital to industry and agriculture were being produced than in any other continent. This statement excludes Communist areas on other continents but might well hold true even if such areas were included. Deriving from its exceptionally diversified production, Africa furnished overseas industrialized countries as a w ole a greater variety of key mineral commodities than any other area. In addition, the value of mineral imports from Africa into the United Kingdom and continental non-Communist Europe probably exceeded the value of such imports from any other area if gold is included and mineral fuels excluded.

Jan 1, 1966

By Frederick C. Trutt

A guide to the development and utilization of an interactive mine-power-system fault program (Z-bus by algorithm) is presented. Theoretical foundations, as well as implementation considerations are discussed with respect to the mine-power system. Alternative Kron reduction techniques are presented along with a triangular-storage method for storage conservation. Program capabilities include the analysis of balanced and unbalanced (line-to-line, line-to-ground, and line-to-line-to-ground) fault situations using symmetrical component theory. To account for phase shifting in delta-wye transformers and zero-sequence network constructions, transformer and load configurations are specified by the user. The positive-and zero-sequence connections needed for network conformity are automatically constructed with the required impedances.

Jan 1, 1979

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980