Search Documents

By F. Sawyerr

A bubble population balance model is proposed for the prediction of Sauter mean bubble diameters in mechanical flotation cells. In the model, the flotation cell is treated as two separate, statistically homogeneous zones?the impeller zone, and the bulk tank zone. Balance functions for the rates of bubble breakage, coalescence, recirculation and inlet-outlet events are proposed based on classical chemical engineering research in two- and three-phase fluid mixing systems. An initial simulation of the population balance model shows trends in bubble size distributions comparable to measured distributions in industrial mechanical flotation cells.

Jan 1, 1998

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Junior S.J. Ramokgopa Immediate Past President J.R. Dixon Honorary Treasurer J.A. Cruise [ ] Annual report In accordance with the current management policy, this report on the activities of the Institute is presented under eight main headings: 1. Interests of Individual Members 2. Technical Meetings 3. Publications 4. Regional Development 5. Engineering Science and Technology in South Africa 6. International Liaison 7. State Liaison 8. Management and Administration.

Jan 1, 2001

By E. Pizarro, A. Videla, G. Compan

One of the main problems related to mining investment decisions is the use of accurate prediction models. Metallurgical recovery is a major source of variability, and in this regard, the Chuquicamata processing plant recovery was modelled as a function of geomining-metallurgical data and ore characteristics obtained from a historical database. In particular, the dataset gathered contains information related to feed grades, ore hardness, particle size, mineralogy, pH, and flotation reagents. A systemic approach was applied to fit a multivariate regression model representing the copper recovery in the plant. The systemic approach consists of an initial projection of the characteristic grinding product size (P80), based upon energy consumption at the particle size reduction step, followed by a flotation recovery model. The model allows for an improvement in the investment decision process by predicting performance and risk. The final geometallurgical model uses eight operational variables and is a significant improvement over conventional prediction models. A validation was performed using a recent data-set, and this showed a high correlation coefficient with a low mean absolute error, which reveals that the geometallurgical model is able to predict, with acceptable accuracy, the actual copper recovery in the plant.

Jan 1, 2015

By T. E. Pogue

This paper traces the co-operative initiative undertaken by South Africa?s gold mining companies through the Chamber of Mines Research Organization (COMRO) in development of hydraulic technologies. After a brief description of the structure of these technologies? development under COMRO?s stewardship, the paper turns to an overview of the structure of innovation within which these hydraulic technologies were developed. A central focus of this paper is systematic review on whether similar technologies are likely to emerge in the present system of innovation and the role played by innovation policy.

Jan 1, 2006

By J. R. Cole-Baker

An independent technical audit by a consultant is part of the accountability process of publicly owned or publicly quoted companies when raising finance through share issues or loans or the sale of equity, and of banks or development funds when granting loans. Africa is undergoing a renaissance in investment in its mining industry. It is forecast that capital investment, in major mining projects in Africa, will be over US$ 4.4 billion, in the next few years. Most, if not all, of the capital to be raised will require an independent technical audit. The aim of this paper is to assist the management of mining companies seeking finance in appreciating the role of such technical audits. The reasons for such audits, especially to attract international investment, are listed. The role of the audit is explained in assessing the underlying robustness of the company as ?a going concern? and the viability of any ?expansion plans?. Its use is emphasised in establishing the underlying value of the company based on the mine life as supported by the mineral reserves. The independent consultant role is stressed as a representative of the parties in a finance deal who cannot, in practice, carry out their own detailed and specialized technical due diligence. The various components of a typical audit are examined with examples of critical matters which may require resolution. The definitions, which are used commonly in audits, in respect of competence and reserves and resources, as stated by various regulatory bodies, are compared.

Jan 1, 1998

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By S. Blancher, A. Perroton, H Smith, T. Nzima, T. Wallmach, V. Dieudonné

Chromite beneficiation is generally performed by crushing and density separation using spirals. At the Dwarsrivier Chrome mine spiral efficiencies seam to vary, the reason for which is not evident. This sometimes results in the production of low-grade products, which are sold at relatively low prices. This paper represents a Qemscan® study that investigated mineralogical reasons for these variations. Variations in liberation of chromite particles as well as variations in chromite compositions were investigated. The results showed that the so-called low grade chromite product can be improved to become a high grade chromite product by means of a refinement in mineral processing. A detailed Qemscan® database (SIP file) was developed to account for variations in chromite chemistries. It can be shown that chemical variations with respect to Cr, Al, Mg and Fe in chromite particles reporting to the scavenger tails are larger than in the high grade product. A combination of these chemical variations together with a decrease in liberation of chromite particles in the scavenger tails can potentially help to recover more chromite particles from this specific process stream.

Sep 1, 2021

By L. L. Godirilwe, and A. Shibayama, G. Danha, K. Haga, Y. Takasaki

Selective extraction through leaching of an amorphous slag obtained from a base metal smelter plant in Botswana is investigated in this paper, where the main objective is to optimise the experimental variables that would result in the maximum selective extraction of the three base metals (Ni, Cu and Co) from the slag waste. Mineralogical tests showed that the sample is composed mainly of fayalite (Fe2SiO4), with a total entrapped metal sulphides content of about 1.0 wt.% occurring as fine occlusions in the fayalite phase. In our experimental program, we compare the effectiveness of two common leaching techniques. In the first method, we use sulphuric acid to carry out atmospheric beaker leaching tests, and in the second method we use high pressure oxidative leaching. The effects of acid concentration, oxidant addition/oxygen partial pressure and pulp density on metal dissolution rate are examined. The optimal Ni, Cu, Co extractions of 80.5%, 81.9 and 98% respectively were obtained under high pressure oxidative leaching conditions (150 oC, 0.6 M H2SO4, 0.5 MPa O2), with substantially low dissolved Fe of 9.6%, the majority of which was removed as jarosite in the residue. Atmospheric beaker leaching yielded poor extractions of Ni below 40% when sulphuric acid combined with hydrogen peroxide (1.0 M and 0.6 M respectively, 65 oC) were used for leaching, while Fe, Cu and Co dissolutions were each about 80%. Therefore, using high pressure oxidative leaching provides a possibility to effectively extract Ni, Cu and Co while producing an environmentally benign residue, thus alleviating the current adverse environmental issues associated with the abandoned smelter slag. Keywords: Slag, amorphous, fayalite, atmospheric beaker leaching, high-pressure oxidative leaching, extraction

Jan 1, 2020

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By B. Samanta

A quality characteristic analysed through construction of the Shewhart control chart is required to be normally distributed. In mining applications, this assumption is often violated as many quality characteristics follow skewed or lognormal distribution. In this paper, two methods were investigated using a heuristic approach for setting up the control limits for a skewed population. Based on these approaches a Mode chart, and a Weighted Variance (WV) control charts were constructed. The performance of the proposed methods was compared with the normal based Shewhart method through a case study conducted in a surface mine supplying iron ore to a steel plant. A simulation study was also conducted to evaluate the effectiveness of the proposed methods over the Shewhart method. The study revealed that the Shewhart control charts generated more out of control alarms compared with the Mode and Weighted Variance control charts for a skewed population of Fe%. The simulation results also revealed that for extremely high skewed population, the WV control chart and Mode control chart provided higher probability of coverage than the Shewhart method; although the detection rate (probability of detection) of out of control condition for these methods was slightly reduced compared with Shewhart method.

Jan 1, 2004

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002