Search Documents

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By Rainer Kahrger

During the last decade, advances were made in solvent extraction/electrowinning (SX/EW) technologies. Combined with heap leaching, these technologies made it viable to exploit large, low-grade oxide copper deposits. The El Abra Mine is a good example for such a deposit. The deposit is situated in northern Chile at an elevation of about 4,000 m (14,000ft), 70 km (45 miles) north of Calama. Codelco sold 51% of the El Abra to Cyprus Minerals in June 1994, with Codelco retaining the balance. In 1993, Cyprus and the engineer on the project began discussions withinternational companies regarding the materials-handling system requiredfor the project. These early discussions were considered critical for this fast-track project.

Jan 1, 1996

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Derek J. Penrice

The Caltrain Downtown Extension (DTX) project will extend commuter and future statewide high-speed rail service into the Transbay Transit Center, which will be located in the business district in downtown San Francisco. The DTX project includes 1.5 miles of underground construction, comprising complex sections of mined and cut-and-cover tunnel. As part of the DTX preliminary engineering process, development of appropriate contracting practices, including contract packaging, procurement methods and contract terms for the underground construction, has been initiated. This paper provides a summary of the evaluations undertaken, preliminary conclusions reached, and proposed next steps to promote industry interest and maximize bid competition.

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By C. Roos

"Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years. However, many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize, and even embrace, the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process.Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation, but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple orebody realizations to provide a thorough unbiased picture of the geologic uncertainty. However, most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter.Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this article presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid- to long-term mine plans while continuously monitoring the uncertainty in the results. The aim of this article is that by demonstrating the usefulness of such a system, mining companies will encourage engineers, geologists and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 8, 2017

By A. Singh

"Considering the dominant role of fertilizers in global phosphate production, it is evident that with the ever increasing development in agriculture there will be a growing demand for phosphate beneficiation. With the rapid depletion of high quality reserves, investigations into more complex and lower grade ore bodies are required. The Minerals Processing Division at Mintek has been involved in process development and flowsheet design projects on phosphate resources since 2003. This paper will discuss the processes that Mintek has explored and employed to upgrade various phosphate ore bodies (>30% Phosphorous Pentoxide (P2O5)) in preparation for end user application. These are aimed at an improved understanding of ores in terms of their varying mineralogy and the development of appropriate process routes to meet product specification. OVERVIEW OF MINTEK Mintek is a state owned science council that undertakes R&D, consulting and sells products and services into the minerals beneficiation industry. Mintek has been in existence for 83 years with a current permanent staff complement of 750 of which 300 are professionals with a tertiary education. Being a non-profit organisation, the majority of funding comes from state grant and earmarked funding. All research is needs-driven exploring innovation through technology and process optimisation trends. Owing to a solid base of expertise, extensive laboratory and pilot facilities, and a historical database of knowledge, Mintek is well positioned and equipped to execute projects on a scoping, feasibility, prefeasibility and bankable level. USES OF PHOSPHATE Phosphate is the component in fertilizer essential for root and stem development in plants as well as rejuvenation of harshly depleted soil for which there is no agricultural substitute. Phosphate rock is essential for global food security with 87% used in the production of fertilizers. In agriculture as fertilizer, phosphate is one of the three primary plant nutrients in addition to nitrogen and potassium. In former times, it was simply crushed and used as is, but the crude form is now only used in organic farming. Normally it is chemically treated to make Single superphosphate (SSP), Triple superphosphate (TSP), or Mono-ammonium phosphates (MAP) and Di-ammonium phosphates (DAP), which has a higher concentration of phosphate and is more soluble, thus more suitable for plant absorption."

Jan 1, 2018

By Bruce Geller

The 2005 Prospectors and Developers Association of Canada (PDAC) convention continued the upbeat mood found in 2004. The global mining industry is booming due to higher commodity prices in nearly every sector. Other factors include low commodity inventories, China’s strong resource demands, the weak U.S. dollar, the very strong Euro, global uncertainties, an almost overripe investment climate for natural resources and the highest mining exploration budgets in seven years. Even unglamorous commodities, like iron, uranium and zinc, received copious attention in talks, the investors’ exchange, the core shack and in certain hospitality suites. The following impressions were gathered at the convention and enhanced by conference handouts and some abstracts that are available on the PDAC’s Web site, www.pdac.ca. At least 119 papers were presented, almost twice last year’s number.

Jan 1, 2005

By Joel Lööw, Jan Johansson, Lena Abrahamsson

In this study, we try to illustrate what new technology can mean for the individual miner. We formulate the notion of Mining 4.0, where we attempt to create an image of how the future might look from a miner’s perspective and how mining companies might navigate their way to a future that works for all miners. 

By W. P. Barnett

In 1988, the U.S. Department of Energy's Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation, and advanced cycloning. Each technology relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. Research projects designed to expeditiously develop each of these technologies to the point of commercial viability were initiated. This paper will present the status of these projects and the application potential of each technology to coal beneficiation.

Jan 1, 1992

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By P. T. Bissert, L. Yan, M. D. Klein

"Since 2008, the U.S. Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (MSHA, 2008). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force (2006) recommended an apparent temperature limit of 35 °C (95 °F) for RAs. In Title 30 Code of Federal Regulations Part 7.504, or 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 35 °C (95 °F) inside an occupied RA (MSHA, 2016). The apparent temperature is calculated using both air temperature and relative humidity (Steadman, 1979).Calculations can be used to deter-mine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, the mine temperature could be assumed to re-main constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. Re-search conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) shows that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (Yantek, 2014). Thus, calculations performed with the assumption that the mine temperature is constant would underpredict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, there has been no research to confirm that the mine air temperature is the appropriate basis."

Apr 1, 2017

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996