Search Documents

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

By Tim McMahon

"A slurry is any combination of liquids and solids where solids make up more than 10 percent of the mixture. Mining operations create various types of slurries from processes such as dewatering, bitumen extraction in oil sands, concentrator plants, milling operations, tailings, lime addition and so on. The mines then transport these slurries through pipelines (Fig. 1).Slurry valves are used when the mine needs to transport ore a long distance and there are no other viable transportation methods, such as roads or railroads.Severe service valves must be used in slurry applications and they must be tested to ensure reliability. This article describes how Emerson designs and tests its Fisher valves for use in mining slurry applications.Slurry pipeline valvesWithin a slurry pipeline system, valves are required as part of the pumping stations, choking stations and isolation stations. There may be multiple pumping stations depending on the length of the pipeline or the terrain it crosses. Choking stations are used to reduce the velocity and the pressure in the pipeline, either before a pumping station or at the end of the pipeline, and to ensure the pipeline does not slack (remains full and pressurized). Isolation stations exist so that a pig (a device sent through a pipeline to clean or inspect the pipe) can be inserted or removed from the pipeline.Typical valves used in a slurry pipeline are severe service ball valves. The valves use floating balls that are held between the seats and are not pinned or permanently attached to the shaft that rotates the ball. The inside diameter of the ball typically matches the pipeline inside diameter, enabling the pipeline to be cleaned or inspected with a pig.They can be built to accommodate the high pressures required for the typical slurry pipeline. These pressures can require up to ASME Class 2500 valves and flanges. The valves can get qlarge, up to NPS 36 inches.Specialized segmented ball valves and slurry knife gate valves are also used in some slurry applications when pressures are lower, in the ASME Class 150-300 range."

Sep 1, 2019

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By C. Özgen Karacan

The formation of the gas emission zone in longwall mining and the potential amount of gas in this zone are factors of local geology and spatial variability within this geology. Therefore, geostatistical methods can be used for modeling and prediction of gas amounts and for assessing its uncertainty in the gas emission zone of longwall mines. This study used core data obtained from 64 exploration boreholes drilled from the surface to the bottom of the Pittsburgh coal seam in a mining district in the Northern Appalachian basin. After identifying important coal layers for the gas emission zone, semivariogram modeling was conducted for different coal seams to define the distribution and continuity of various attributes. Sequential simulations were performed for stochastic assessment of these attributes to calculate gas-in-place (GIP) in each coal seam. GIP calculations for coals of various gas emissions zones were combined and ranked for their cumulative distribution function to find GIP in the caved zone and in the fractured zone at the 5%, 50%, and 95% quantiles. Fifty percent quantile results were later used to isolate a panel from the whole area and create a mosaic representation corresponding to the daily advance rate of the longwall face. This approach helped to estimate the daily emissions of this panel from the caved zone and from the fractured zone. Results showed that gas-in-place in the Pittsburgh coal seam, in the caved zone, and in the fractured zone showed spatial correlations that could be modeled and estimated using geostatistical methods. This study showed that gas-in- place volumes in the study area may be as high as 12.3 Bscf and as much as 3.5 MMscf per acre of mining.

Jan 1, 2012

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Reed S. C. Rogers

The most widely used machines for grinding coal to the sizes prescribed for the pulverized coal firing of furnaces, boilers, and kilns are the vertical ball-race, roller-race and roller-bowl types of mills. However, the increased use of coal has led to an increased use of tumbling ball mills for coal grinding. Specifically, air-swept ball mills are now a part of many dry pulverized coal firing systems, offering the advantages over vertical mills of lower maintenance costs and the ability to handle strong or abrasive (high ash) coals. The current use of wet ball mills is to prepare coal-water slurries for direct combustion, although in time they may also find routine application for preparing slurry feed for coal gasifiers. In either application, wet ball mills ofer the advantages that coal grinding and wetting can be accomplished in a single step, and that the mills are readily used with fine wet screens to assure top size control in the slurry product. The simulation of tumbling ball mills with mathematical models has reached a fairly advanced stage, but the concepts have been applied only recently to coal grinding. As this paper will demonstrate, however, significant progress has been made in the use of models in ball mill circuit design for coal grinding. Included is a description of the techniques used for simulation, recommended parameter estimation methods, and demonstrations of process engineering calculations for large scale coal grinding circuits.

Jan 1, 1986

By Albert W. Deurbrouck

The coal reserves in the United States are estimated to be in excess of 300 billion recoverable tons, and current projections of energy requirements indicate our increased dependence upon these reserves. The Department of Energy's Energy Outlook for 1984 projects that coal consumption in the United States will increase from 737 million tons in 1983 to 958 million tons in 1990, and then to 1,110 million tons in 1995 (Table 1). As shown in this table, the future utilization of coal in the United States is closely tied to the electric utility market, a market that consumes about 85% of the coal produced. Be- cause of this dependence on the utility market, the uncertainties of new environmental regulations, particularly those concerning sulfur emissions, could have a significant adverse impact on future coal demands in the United States. SULFUR IN U.S. COALS Most of the Nation's coal reserves contain too much sulfur to be fired directly and meet existing emission control standards. In Table 2, the sulfur contents of the coals of the eastern United States are summarized by sulfur levels according to regions. While the coals of some of the eastern regions are predominantly high in sulfur content, it is important to recognize that large tonnages of coal with relatively lower sulfur content are available in these regions. Furthermore, an often significant portion of the sulfur occurs in the form of iron sulfide (Fes2 or pyrite). Because pyrite occurs as discrete particles of high specific gravity, it can often be removed by simple, inexpensive physical coal beneficiation techniques after being liberated by stage crushing. The potential for physical removal of pyrite by conventional specific gravity processes combined with stage crushing is summarized in Table 3 on a regional basis.

Jan 1, 1986

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By M. Mankosa, G. Taylor, G. Luttrell, J. Yasalonis

Several industrial-scale HydroFloat separators have recently been installed at Mosaic’s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale, and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The apparent benefits, theory of operation, and commissioning of the equipment are also discussed.

Jan 1, 2007

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015