Search Documents

By W. E. Crandall

The Star-Morning mine is a. 1000-ton-per-day lead-zinc producer located in the easterly part of the Coeur d'Alene Mining District of North Idaho. The property includes both the Star and Morning mines which are located on the westerly and easterly portions of the same complex of veins. The mine is 70% owned by the Bunker Hill Company (Gulf Resources, Inc.) of Kellogg, Idaho, 30% owned by Hecla Mining Company, and operated by Hecla Mining Company with head-quarters in Wallace, Idaho. One of the characteristics of mines in the Coeur d'Alene District is that many of the ore bodies extend to very great depths. The Star is no exception, but rather a leading example. The complex of near vertical veins and ore shoots extend some 7000 feet below the surface at present, with a maximum strike length of about 4000 feet. Ore has been mined on 20 separate veins and ore structures. More than 50 miles of headings have been driven and nearly 23 million tons of ore mined since the Morning mine started in.189S. The problems of mining at such depths are formidable temperature on the bottom level is 1100 F and high humidity problem. Pressure from the sheer weight of rock is as high foot. This paper will deal with providing a new access to the deeper levels of the mine and the installation of a hoist and related items to service these levels. By the time development had reached the 7100 level (Figure 1), it became apparent that a different 'hoisting system was going to be necessary if we were going to continue to mine at a profit. The main shaft extended to the 4000 level at which point a ?:3100"'foot winze shaft provided access to the 7100 level. The two hoists were limited to handling 3-ton payloads at 1200 to 1500 feet per minute. Some ores are still produced from above the 4000 level but as these ore reserves become depleted the hoisting of the desired tonnage (1000+/day-) from the lower levels of the mine would exceed the capacity of the existing hoisting system. A decision was made to sink a new vertical shaft at a point well in the south wall of the ore bodies where strong rocks and a minimum of faulting was expected and to purchase and install a new hoist capable of hoisting over 7000 feet. This new' shaft, designated as the No. 4 Shaft, was planned to reach 2000 feet below the 7100 level which was the deepest level at that time. The hoist would be in-stalled on the ,main 2000 Adit level which is used as an access and haulage level to the concentrator and surface plant in Burke.

Jan 1, 1971

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By D. L. Crouse

The worldwide talc industry has experienced significant changes since the 1980's. Consolidation of companies and operations in Europe, Australia, and North America has altered the face of supply and distribution. Imports of Chinese and Australian crude have increased competition and product options. The number of processing operations without local mines has moved competition closer to the market area. Quality controls related to ISO certification and tighter specifications demanded by the customers have altered the way our mines and mills operate. Ceramics, coatings, and paper applications continue to consume the majority of processed talc.

Jan 1, 1997

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation's No. 1 mine in northern West Virginia.

Jan 1, 1982

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

By M. T. Ityokumbul

Flotation is a surfaced-based separation process that exploits the differences in the hydrophobicities of the components. In the present paper, a review of both established and emerging nonmineral applications of flotation (oil removal, paper de-inking and separation of plastics) is presented and discussed. For each application, the theory of the process is compared and contrasted with mineral flotation. It is shown that the mass-transfer approach to flotation offers a good starting point for the analysis of these separation processes.

Jan 1, 1999

By Steven E. Mischler, Jay F. Colinet

The study analyzes the impact of the Continuous Personal Dust Monitor (CPDM) on reducing overexposures to coal mine dust. It compares compliance sampling data before and after the implementation of the CPDM and the 2014 MSHA dust rule. The results indicate a significant reduction in the percentage of samples exceeding the dust standard for various mining occupations, highlighting the effectiveness of the CPDM in improving miners’ health and safety.

Feb 22, 2022

By Randall D. Peterson

Strip mining with draglines and other surface equipment has traditionally been the method of choice for mining shallow deposits. This is particularly true for soft deposits that require little or no blasting. High rates of productivity and low operating costs have set this standard. However, these methods can be improved. Strip mining methods are batch processes and difficult to accommodate in processing. Moreover, they are encumbered with overburden removal, reclamation expense, and human inefficiencies. This paper describes the invention of a novel shallow earth mining technique called the Softwall Mining Method. Softwall Mining is an adaptation of longwall mining for loose earth conditions. The method was specifically invented for recovering phosphatic clay ore from beds in North Central Florida, but is likely to be suitable for a number of other minerals as well. Potential deposits for which the method may be well suited include placers, disseminated deposits in soft host rocks, bauxite, soft coals and lignite deposits, and other deposits where overburden will subside readily and where the ore can be hydraulically broken and slurried. Unit operating cost advantages are expected over the current dragline systems used. The Softwall mining advantages are its high rates of productivity, control and automation of the mining process, reduction of dilution and waste, and elimination of the majority of stripping and reclamation.

Jan 1, 1998

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By F. Calizaya

This study summarizes the ventilation requirements for the highly mechanized PT. Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The deep ore zone (DOZ) is a coppergold deposit that is being developed underneath the current intermediate ore zone (IOZ) mine. One of the company's current plans is to prepare this mine for a steady ore flow of 25 kt/d (27,500 stpd) by 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 2000

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001