Search Documents

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

TABLE TUNNEL NAME OWNER LOCATION STATE TUNNEL USE LENGTH (FEET) WIDTH (FEET) BID YEAR STATUS Gateway Tunnel project Amtrak Newark NJ Subway 14,600 24.5 2015 Under study

Sep 1, 2013

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By P. Eger

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Wieda Azani, Alexander Tarigan, Willem de Beer

In block caving, the rates and sequencing of undercut production blasting, drawbell blasting, and mucking are the key levers for attempting to manage cave performance. Cave performance encompasses a range of factors, which include growth, shape and the effect of the cave on the abutments, excavations, geological structures and lithology. We compare production data in several panels in the Grasberg DMLZ and GBC block caves with the seismic response in work areas, around geological structures, and in geotechnical domains. These comparisons enable evidence-based conceptualising of the effect of production rates and mining layouts. By also considering the correlation of seismic release rates in different parts of the rock mass, the wider influence of a cave can be gauged through considering possible stress and / or deformation transfer. This concept is not novel, but it is rarely implemented in a routine fashion, principally because production data rarely are easily available. Previously, it has also been used to retrospectively compare seismic hazard between different mines. This paper discusses practical, day-to-day tools to manage seismic response to mining. Therefore, the paper presents a methodology for presenting seismic release and production rates on integrated plots at any time to facilitate quick identification of correlated spatial regions. This methodology explores the production data collection and geolocation at Grasberg, which will be described in some detail.

Apr 26, 2022

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world's seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

By G. Montes-Atenas

Throughout the years, research studies have reached a consensus in acknowledging the relevancy of surface chemistry phenomena on minerals separation and metals extraction. Many techniques, and notably, scanning electron microscope-based technologies have revolutionised the entire mineral processing industry. Nevertheless, the comprehensive understanding on how surface chemistry properties influence the performance of many processes involving ores is still a challenge, a matter of controversy. The latter is mainly due to the fact that all interfacial processes do not necessarily require stoichiometric and well defined atomic structures. This is particularly true in the case of sulphide minerals which are well known to be superficially unstable in aerated media. When trying to measure any variable related to mineral-mineral or mineral-aqueous solution interfaces, there are too many unknowns regarding how sensitive the interface is when facing sampling protocols and sample handling. The aim of this research work is to make a case for improving future concentrators? survey protocols. It suggests a methodology to study effectively chemical changes at the outmost mineral surface layer at different stages of a mineral processing operation. The sampling protocol and sample handling is presented in details and it is applied to the regrinding stage of an industrial plant.

Feb 27, 2013

By R. Abel, T. Wildeman, N. Heflin

A study was conducted to assess environmental effects of waste rock piles on water in the Russell Gulch area. Each pile was rated on physical characteristics of proximity to an ephemeral gulch, extensiveness of erosion features, size, presence of vegetation, and presence of a kill zone. Chemical assessments focused on three leachate tests performed on waste rock samples. Ratings were based on pH, conductivity, acidity, and analysis for 31 metals using inductively coupled plasma emission spectroscopy. The chemical and physical assessment of each site is used to make a rating of each pile on its overall potential to deliver contaminants.

Jan 1, 2004

By Alvin Kaufman

Malthus, an eighteenth century economist, predicted a rather dismal future for the world. It was his contention food supplies would not be sufficient for the population of the world because the economy of a nation grew arithmetically while population increased geometrically. As a consequence, within a relatively few years mass famine would spread throughout the world. This prophecy, based on an agrarian economic situation, did not come true at least insofar as the Western World was concerned. In largo measure, the salvation of our part of the earth resulted from the growth engendered by the Industrial Revolution. Throughout much of today's world, however, the Malthusian theory seems to be coming true. The advantages and benefits of the Industrial Revolution have net reached all nations. Further, the situation has been compounded by the benefits of modern medicine. This has reduced child mortality and extended life expectancy, but placed no limitations on births in the developed countries, child mortality has declined to 2 percent and adult life expectancy has doubled, but education and general prosperity have resulted in voluntary limitations on pregnancies thus partly offsetting the increased chance of survivals Even so, the present rate of population increase in Europe is approximately 6 percent per decade, and somewhat higher in the U.S., Japan, and other developed countries. The world as a whole, however, is expected to double its population by the year 2000, This would imply a rate of increase in the less developed countries approximately four times that in Europe.

Jan 1, 1966

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By Ben W. Burdett

Since the late 19701s, the use of microcomputers in the minerals industry has grown to the point where today they can be found in virtually every plant within the industry. Their use in every aspect of instrumentation and control has increased the ease of operation and control of every phase of mineral processing. Their incorporation in sensors, transmitters, indicators, and controllers in addition to their use in distributed control and computer systems has provided operators with more timely accurate information than they have ever had before. This has led to an increase in the operator's effectiveness and an improvement in overall productivity. The ultimate aim of plant control is to maximize recovery in the mineral processing operation, and the microcomputer has spawned many tools that are now making this goal attainable. This paper discusses individual use of microcomputers in the areas previously mentioned as well as their collective use in overall control systems. The incorporation of local control systems in total plant control including the communication of information throughout all levels of plant management is also discussed. Finally the role the microcomputer is playing in today's plants is illustrated with numerous references to current examples.

Jan 1, 1985

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By Leonard Sugin

The requirements of today's and tomorrow's markets led to a new generation of facilities which handles large tonnages annually, loading them into larger vessels, at higher rates, efficiently and reliably, with minimum labor input, and significantly greater attention to the environment. A great variety of products are handled, including various grades of metallurgical and steaming coal, coke, iron ore in its many forms, shapes and moisture content, phosphates and fertilizer products, bauxite and alumina ores, limestone, sugar and grains, cement and many other products. When we examine the annual tonnages involved in these movements the economic value of handling these products on a bulk basis can be readily seen. Although nearly all these products have been handled by continuous bulk conveyors for many years, recent governmental response to environmental concerns require a re-evaluation of previous procedures. Most air pollution and emission control regulations and ordinances have recognized several specific sources of pollution. Detailed regulations and requirements have been developed concerning smoke emissions, emissions of visible air contaminants and particulate matter from power plants, heating plants, refuse burning equipment, coke ovens, steel furnaces, kilns, and other industrial installations. Although fugitive dust is also an environmental pollutant it is governed by regulations that are more general and therefore, more difficult to apply. A general definition of a "fugitive particle" is any matter which escapes or becomes airborne from an operation or which is emitted into the atmosphere without passing or being conducted through a flue, pipe, stack or other structure designed for the purpose of emitting air pollutants into the atmosphere. This paper deals with the aspects of fugitive dust emissions as they apply to shiploading. Fugitive dust emissions control is important not only because of environmental regulations but also to prevent the loss of valuable product, reduce housekeeping, and reduce breakdown and maintenance problems to land and vessel equipment. The environmental controls for a belt conveyor system are those which will restrict the emission of fugitive dust particles and can be considered as follows:

Jan 1, 1977

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

By Michael Clar

Total suspended solids (TSS), generally referred to simply as sediment, is one of the four major parameters of water pollution associated with surface mining activities. The other three para¬meters are iron, manganese and pH. Currently the Environmental Protection Agency (EPA) is in the process of developing and implement¬ing effluent limitations for these pollutants pursuant to section 301 of the Federal Water Pollution Control Act Amendments of 1972, 33 USC 1811.1 To date, effluent guidelines for existing point sources have been published, and guidelines for new sources are forthcoming. The effluent limits which have already been developed for TSS have been subjected to some controversy.1 Some industry spokesmen have indicated that they may be unable to meet these effluent limitation guidelines for TSS. The industry claims that in certain areas the suggested limit is unattainable since high suspended solid loads already exist in streams due to numerous and various sources of nonpoint pollution which include agriculture, silviculture and urban construction for which no TSS effluent limits have been set. An opposite viewpoint asserts that the TSS limitations are too lenient since permit data from the Regions (U.S. EPA Regions) indicates present compliance for several companies under more stringent TSS limits. The experience at the Centralia mine in Washington is one example.2

Jan 1, 1977

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996