Search Documents

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flowschemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none has led to a satisfactory conclusion. A technique has been developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program has been constructed which makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems.

Jan 1, 2002

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By Douglas F. Crickmer

Pocahontas Land Corporation, a wholly-owned subsidiary of Norfolk and western Railway Company, owns a 100,000-acre block of coal lands in Martin, Johnson, Pike, Floyd and Lawrence Counties, Kentucky. These holdings were largely acquired in three major purchases between the years 1942 and 1959. The area is undeveloped and constitutes a part of the coal reserve for future mining. This block, which is principally in Martin County, lies in a triangle formed by the Levisa and Tug Forks of Big Sandy River on the sides with Dewey Dam at its base and the Town of Louisa at the apex. The topography'is typical of eastern Kentucky and consists of steep hills rising from 500 to 800 feet above creek level. There is little level ground in the area. As a matter of fact, some roads are on the creek bottoms with what little bottom land is available in the hollows being utilized for small-scale farming. The steep hills are marked by three separate massive sandstone formations which form cliffs ranging from 40 to 100 feet in height.

Jan 1, 1964

By John E. Feddcck

New York City's $360 million North River Water Pollution Control Project is part of New York State's plan to clean up the Hudson River. The project is to provide a sewage treatment facility capable of accomodating a peak waste water flow of 330 MGD which will in great measure eliminate the 192 MGD of raw sewage that N. Y. C. discharges into its surrounding waters. Eleven miles of intercepting sewer lines must be constructed along the west side of Manhattan Island to service approximately one-half of the island. The first contract award was for a 4134 ft. sewer tunnel with a finished inside dimension of 16' x 16'. This main intercepting sewer will feed a sewage treatment plant located on and adjacent to the Hudson River. The tunnel is parallel to the river and is located under 12th Avenue between 125th Street and 143rd Street. The Penn- Central Railroad tracks are above and just to one side of the tunnel location. The working tunnel diameter is 21 ft. and numerous problems of support, mining method, and ground control have been encountered. (see Dwg. 1)

Jan 1, 1970

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

By S. G. Britton

"INTRODUCTION Strategies to improve performance in mining production, maintenance and mineral processing operations has evolved over time from straightforward time studies of individual machine performance in the 1960’s-1970’s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980’s-1990’s . These newer strategies fall under the broad descriptive category of “Operational Excellence”. Operational Excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining includes the following: • Six sigma for addressing errors within mining or milling process and work standards • Lean manufacturing to optimize organizational and operational performance through continuous improvement. There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts. The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to affect the change versus the estimated value gained. The practice is identified as the value mapping process. This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement.THE RABBIT LAKE MINE AND MILL The Rabbit Lake Mine and Mill are located in northern Saskatchewan, Canada on the shores of Wollaston Lake (Figure 1).The mine was discovered in the mid-1960s and was built by Gulf Minerals, Ltd. The mill began processing uranium ore into yellowcake in 1975 from an adjacent open pit mine. A whole ore acid leaching followed by solvent extraction and precipitation forms the basic milling processes. The operation continued to produce yellowcake through a succession of open pits and finally opened an underground mine in the early 1990s. Since beginning production, over 200 million pounds of yellowcake has been packaged from the site, making it the sixth highest producing uranium mine of all time."

Jan 1, 2016