Search Documents

By Joseph M. Chelini

Today, the two major operating costs of rubber tired off-road equipment are diesel fuel and tires. Mine Management has minimal control over the ever accelerating diesel fuel costs. However, they can exercise control over abnormal tire costs. Fortunately, with available technology and cost analysis methods, experience shows us the outlook for controlling tire costs is encouraging. Most earthmoving operations using off-road, rubber tired haulage and support equipment have abnormally high total tire costs. These costs, utilizing Tire Information Management, have been reduced more than 30%; 20% can often be guaranteed. Management Apathy on the subject of tires in a complex mining operation perhaps can be understood, but management apathy applied to an abnormally high operating cost, of which tires are, begs for a solution.' Tires have been professionally neglected for many years in most mine operations. This is exemplified in the January, 1982 issue of Mining Engineering by Charlie Son in his article Reducing Earthmoving Tire Costs. He compared the efforts to improve diesel engine costs to the same efforts given to earthmover tires.

Jan 1, 1983

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By Emily Wortman-Wunder

While the mood at the 2013 annual joint meeting between the Pittsburgh Coal Mining Institute of America (127th Annual Meeting) and SME Pittsburgh Section (68th Annual Off-the-Record Meeting) in Canonsburg, PA was subdued following a rocky year in the coal industry, attendance was down only slightly, to 300, and overall, the meeting?s focus was optimistic about the future of coal. The conference began by addressing one of the central challenges of coal mining head-on with a keynote address on the status of safety in the mining industry. Noting that two more U.S. miners had died in 2013 than by the same date in 2012, the National Mining Association?s (NMA) Senior Vice President of Regulatory Affairs Bruce Watzman made a plea for a new approach to safety. He described the NMA CORESafety initiative, a program that promotes proactive safety measures versus a compliance-driven model. CORESafety, described in more detail on pp. 29 of this issue, focuses on developing successful ways to change company cultures of safety and behavior. Other industries that have adopted this approach have seen dramatic drops in fatalities, including the Australian mining industry, which has seen its annual fatality rate drop to nearly zero even while the number of people employed in the industry has soared. The rest of the morning?s sessions explored what is arguably the industry?s biggest challenge right now ? maintaining the social license to operate.

Jan 1, 2014

By J. A. Restrepo, K. D. Luxbacher

"The U.S. underground coal mining industry has recently seen the occurrences of several multifatality events that have interrupted an otherwise steadily improving safety record. These events transpired even with an unprecedented level of government regulations and safety technologies. These events may indicate that current safety practices have reached a level of diminishing returns. Risk management, a safety approach that has been successfully applied in numerous industries including mining, may provide a means to overcome this plateau. Riskgate is an Australian mining risk management program that may be successfully applied in the United States. However, fundamental differences between the Australian and U.S. coal mining industries prevent direct implementation. This paper discusses aspects of the Riskgate body of knowledge that require adaptation for its application in the United States. IntroductionThe underground coal mining industry in the United States has recently seen the occurrences of several high profile, multifatality events. These events transpired in the midst of an unprecedented level of government regulations and modern safety technologies. The recent increase in fatal events in conjunction with minimal declines in fatal and nonfatal injuries over the past decade may signify that current safety practices have reached a level of diminishing returns. In order to surpass this plateau, a modification to the manner in which the mining industry approaches worker safety may be warranted.The implementation of a risk-management- based approach may potentially provide a means for not only surmounting the current safety stagnation but also for achieving the long-desired objective of zero harm.Riskgate is an Australian risk-management- based body of knowledge that shows great potential for application in the United States. This paper discusses aspects of the Riskgate body of knowledge that require adaptation for the U.S. mining industry. The proposed adaptations are based on differences in operating practices and government regulations. This discussion will focus on the three major U.S. risk areas of explosion prevention, ground control and moving equipment."

Jan 1, 2015

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By Donald R. Simon

Money... not many subjects are as personal or as emotional. Hessiod said it well in 700 B.C. "Money is life to us wretched mortals". Are you getting paid enough? Does your company reward its top people? Does coal or copper pay more? Production or engineering? How is the synfuels industry going to influence mining salaries? Do high salaries attract and retain the best people? Do modern compensation systems ensure fairness or destroy entrepreneurial spirit? With our tax system and high standard of living why are we so salary conscious? Salary is not only important for what it can purchase but it is also a yardstick, measuring how well we are doing. We all need money to pay the bills and maintain our standard-of-living, but once we reach a certain point the psychological ramifications become more important than the purely practical side. Even necessary payments like the mortgage and the car are a function of our egos. Are our choices of cars and homes based on simple transportation and shelter?

Jan 1, 1980

By Ernest L. Ohie

In 1939 the Geological Society of America published a summary of the geology of the ore deposits of the Mississippi Valley region, This volume, edited by E. S. Bastin, contained contributions from the foremost students of the area which described theregionalgeologic setting of the various deposits as wel as the detailed geology as then known. The various ideas as to the origin of the ores were discussed with the general, though not unanimous, conclusion that the deposits were hydrothermal products, Only those deposits in the immediate Mississippi Valley area were considered without any attempt to introduce evidence from other districts generally accepted as being of the "Mississippi Valley type." Since 1939, much new information has come from extended studies of two of the important districts described in the 1939 report andimportant extensions of the known ore have been found. Likewise, concentrated geologic efforts have been fruitful in severa "Mississippi Valley type" districts - both U. S. andforeign - not treated in the 939 paper. The wealth of new field information on the structural and stratigraphic relations of this interesting ore type, coupled with the results of theoretical and laboratory studies of the past 18 years, makes desirable a review of our present knowledge and interpretation of these important deposits which for many years have yielded over 20 percent of the world's annual production of lead and zinc, together with large amounts of fluorspar and barite. No restatement of the details of the geologic evidence willbe attempted here; the interested student is referred to the papers cited. Slide No. 1 shows the distribution around the world of the deposits under consideration. A principal thesis of my remarks is that there is so much similarity in all these deposits that it seems necessary for all of them to have had a similar mode of origin, whatever that may be. Variations in the shape, size and mineralogy of the orebodies give each district some individuality, but there are enough of the "typical" characteristics present in all cases to make classification in the "Mississippi Valley type" agreeableto most geologists. Thus the overall process giving rise to the ore solutions surely was the same for all in the group. Either they all have igneous affiliations or they all do not. Acknowledgment of this kinship between deposits in the various districts offers many advantages in trying to arrive at a decision as to just what the origin may have been, for the amount of guiding and limiting evidence which must fit into the hypothesis is greatly increased over that available in any one district, To a certain extent this was recognized by the authors of Special Paper 24 in treating all of the immediate Mississippi Valley areas together; by expanding the consideration to include ore deposits of this type all over the world the changes of success, i.e., arriving at the correct answer, are improved several fold. Since most of these districts are quite simple structurally, a number of hypotheses might fit the facts in any one of them, but if the facts to be met can safely be drawn from all the districts, then the explanations which will fit all the data are much less numerous. One purpose of this paper is to call attention to the field facts that have been reported from the .various areas which seem to have an important bearing on the kind of ore fluid that was responsible for the ore and on the way it circulated.

Jan 1, 1958

By Z. Hyder, M. Karmis

Underground or In-situ Coal Gasification (UCG or UICG), though not a new concept, is now attracting considerable global attention as a viable process to provide a "clean" and economic fuel from coal. Applying improved UICG technology to gasify deep, thin, and low-grade coal seams could vastly increase the amount of exploitable reserves. However, it is imperative that further development of this technology is based on integrating UCG practices and potential environmental impacts with accepted sustainability frameworks and processes. This paper evaluates the potential of UCG to conform to frameworks such as MMSD (Mining, Minerals and Sustainable Development), Natural Step and Green Engineering, in order to define its "sustainable" potential. The paper also discusses the potential contributions of UCG to sustainability during its design, operation, closure, and post-closure phases.

Jan 1, 2011

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By L. L. Lien

In this economic age of high interest rates and softening mineral commodity markets, the mining industry is taking a hard look at how it conducts its business and where economies can be effected. The capital investment to build a new metallurgical facility or open a new property has traditionally attracted substantial investigation, analysis and management attention. The areas of mineral exploitation, financial feasibility, engineering and construction have been studied extensively and their management, although still difficult, have become refined disciplines.

Jan 1, 1982

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

By J. E. Castle

The essential foundation upon which to build an effective marketing program in industrial minerals is the ability to produce competitively mineral products meeting precise customer specifications and to ship them promptly and on schedule. Without this prerequisite, all the other factors in a second marketing program-creative sales management, energetic solicitation, advertising, technical service, new products, etc.are without meaning. The primary image to be created in the mind of customers is that of the reliable and prompt supplier of mineral products at competitive prices and of standard, uniform quality. With this favorable image implanted, it becomes possible to integrate the other essential factors into a strong marketing program; and without this image, little can be accomplished. After having .made provision for the basic product ion position outlined, there are then two fundamental considerations in the design of a successful marketing program for industrial minerals. The first of these is that the number of potential customers for the typical industrial mineral product is, relatively small, and indeed compared to the number of customers for consumer products, the number is actually minute. The second consideration is that the customers for industrial minerals are manufacturers and producers rather than consumers. These two factors lead to a necessity that the marketing program be specifically and uniquely tailored to fit the individual mineral product to be sold and to conform to an existing pattern of distribution.

Jan 1, 1962

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By None None

Use this month wisely — go online and take advantage of your new member benefit. As an SME member, you can read and download for free all of the full-text papers of the Mining, Metallurgy & Exploration (MME) journal, including the 22 papers in the launch Special Issue on Mineral and Metallurgical Processing in Honor of Professor Emeritus Douglas W. Fuerstenau as well as the archived articles of Minerals & Metallurgical Processing (MMP), all the way back to Vol. 1, No. 1. Just follow the instructions on this page.

By Thomas F. Joyce

N L Industries, Inc., MacIntyre Development produces ilmenite and magnetite concentrates from its own open pit operation at Tahawus in New York's Adirondack Mountain region. The ilmenite concentrate is used within the company for the production of titanium dioxide pigments and the magnetite concentrate is sold to heavy media processors. Current production is from South Extension mine, loading by by six-yard Marion electric shovels into 85 ton Lectra Haul trucks. Bench heights are 44' and are drilled with a Robbins Rotary 9 7/8" diameter hole on 25' spacing for a yearly production of 3.4 million total tons of rock. The ore deposit occurs in veins dipping on the average at 40 degrees to the west. The ore body, which is divided into three zones, outcrops at surface and continues to depths of 800'. Zone 1 is a high grade band of thickness 150-200' with an Fe/Tio2 ratio of 2. Below this band is Zone 2, a low grade band of thickness 50-100' with an Fe/Tio2 ratio of 2 and beneath that seperated by a band of anorthosite is Zone 3, a high grade band of irregular thickness 50-450' with an Fe/Tio2 ratio of 1.6.

Jan 1, 1973