Search Documents

By Olav K1omstad1ien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, is the raw material for the Rana Mines which is a division of the state owned steel mill A/S Norsk Jernverk. Activities for the exploitation of the orebodies were commenced in 1902 by the English Dunderland Iron Ore Company. During its operating period the company constructed a total of two large scale concentrating plants. The activities were strongly marked by technical problems and labor disputes. Thus actual production was limited to the years 1904-1908, 1928-1931 and 1937-1939. During these periods a total of 1.9 million tons of crude ore was mined and 0.6 million tons of concentrates produced for export. The present plant commenced operations in late fall of 1964. Up to and including 1976 about 26.6 million tons of crude have been put through the concentrating plant and about 10.7 million tons of concentrate produced.

Jan 1, 1978

By J. F. T. Agapito

OCI Wyoming mines two flat-lying trona seams that are 3- to 3.5-m- (10- to 11.5-ft-) thick, about10 m (33 ft) apart and 250-m- (820-ft-) deep at its Big Island Mine in Wyoming. Continuous miners and a yielding-pillar system have contributed to improvements in resource recovery and productivity. The use of yield pillars minimizes the stresses transmitted from the upper to the lower seam. However, yielding must not impact the good, long-term stability needed to prevent subsidence for a large portion of the mine beneath the Green River channel.

Jan 1, 2000

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

The purpose of this talk is to report the answers to the-'two following questions: I. What unique services does the mining industry expect of mining and mineral processing engineers? II. What suggestions does industry offer to educators to help revamp curricula to meet the needs of a changing industry? As the result of many questionnaires filled out in person by presidents, managers, superintendents, chief engineers, metallurgists, and other responsible individuals in operations and management of large and small metal and nonmetallic mining companies in the U. S., and to some extent abroad, we now have some, specific answers to the above questions. Although answers to questionnaires continue to arrive at this writing (February 10) the volume already received is sufficient to clearly justify certain conclusions and observations. A copy of the tally of the first 117 questionnaires received accompanies this report, and I am certain that a compilation of additional questionnaire data will merely reinforce, the trends in thinking that have been' established thus far. Here are the results of the survey:

Jan 1, 1961

By H. G. Schoenike

A subsequent spin off of the energy shortage is the new life for barite. Over 90% of the barite produced in the world is used as a weighting material in oil well drilling muds. Business is booming; the price of barite has risen; scarcity is imminent, and exploration is going full steam ahead. New barite-producing companies are being formed and many of the barite consumers are considering becoming producers. Prospectors have found a new "love," smaller deposits are being explored, and old deposits, previously rejected, are getting a reappraisal. Even barite tailing piles are being resampled.

Jan 1, 1980

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By Mark Van Dyke, Mark Mazzella, Gamal Rashed, Nicole Evanek, Brent Slaker

In the past decade, there have been several incidents of massive ground collapses in underground stone mines in the eastern United States. Fortunately, these events have not resulted in any fatalities. However, three mine workers were injured and many others were at risk due to the hazard from the fall of ground and/or the airblast associated with these massive collapses. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to better understand the causes of these massive ground collapses to help prevent their future occurrence. The main objective of this study is to investigate the main factor(s)that initiated one of these massive ground collapses. The authors relied on several tools including three-dimensional (3-D) LiDAR scans for the surface subsidence feature and the underground mine workings around the collapsed area, borescope data at multiple locations around the collapse, S-Pillar analysis for average and unfavorable conditions, and numerical models. The emphasis has been placed on the impact of the following limestone pillar stability parameters: pillar width-to-height (W/H) ratio, benching, the existence of karst features, weak roof, and geological discontinuities. 3-D LiDAR scans were utilized to show the shape and the extent of karst cavities observed within stable pillars around the perimeter of the collapsed area. Together, this coupling of field measurements and observations and modeled systems suggests the potential causes of the collapse.

Jul 1, 2023

Paper 1: Risk of gastrointestinal cancers from inhalation and ingestion of asbestos, John F. Gamble Selikoff suggested the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers in an early study of insulation workers. In this paper, John Gamble reports on his extensive review and reanalysis studies that address the relationship between asbestos exposure and GI cancers. The purpose of the review was to evaluate the association between asbestos exposure and risks of stomach, colorectal, colon, and rectal cancers separately. Gamble evaluated exposure?response (E?R) relationships using surrogate exposure methods ??because few individual studies of GI cancer have reported exposure? response analyses.?? The principal asbestos exposure surrogates are: (1) the rate ratio (RR) for lung cancer; and (2) the percent of mesothelioma among exposed workers. Analyzing SMRs for GI cancers from individual studies versus the risk of lung cancer and mesothelioma provides crude estimates of E?Rs for asbestos exposure and GI cancer. Briefly, Gamble justifies the surrogate approach as follows:

Jan 1, 2007

By Jacob Bouke, Jason Janisch, Erik Vlot

The use of conventional tailings deposition methods has been the standard for decades. With the need to reduce the impact of mining, alternative methods are considered when expanding or upgrading tailings handling systems. Converting an existing tailings management system to a more sustainable deposition method during the operation of a mine may incur considerable operational and financial risk, and when assessed more traditionally, does not provide significant advantages. As a result, most mines choose to continue their current technology and add an additional pumping stage or pumpstation to their tailings line in case of a pipeline extension or Tailings Storage Facility (TSF) expansion. This also often involves raising embankments. Changing pumping technology is traditionally assessed by comparing the energy efficiency of current and prospective pumping technology. Despite a reduction in absorbed power, this traditional assessment does not include possible savings in water and the carbon footprint. With the consideration of all these three aspects, alternative pump technologies, such as Positive Displacement (PD) technology, become more economically feasible, providing increased sustainability and enable a site to future-proof their operations. Project feasibility may be affected by the high capital investment required for PD pumps. The benefit of applying PD pumping technology could be enhanced by reducing the volumetric throughput of the pipeline by dewatering the tailings to 65% solids concentration by weight. It was found that despite increasing capital expenditure, the improved reclamation of water will have a positive effect on the direct and indirect cost of fresh water intake to mine operations. This paper seeks to illustrate that in many applications the long-term benefits of investing in sustainable tailings management are optimized when more efficient PD pumping technology is combined with tailings dewatering when upgrading or expanding the tailings handling system.

Feb 1, 2024

By Joseph H. Herz

Recently, the President of the Portland Cement Association, Robert D. Maclean, gave the keynote address at the Rock Products Eighth International Cement Industry Seminar. He said, after listing the seven plagues our industry is suffering, "none of these items I have listed is a sales or marketing problem. Further, none is a problem that can be relegated to long-term study by public or private research agencies. They are here-and-now problems to be faced daily by producers, researchers, equipment manufacturers and consultants. THE DAY OF THE PRODUCTION MAN IS HERE." (1)

Jan 1, 1973

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By J. N. Van der Merwe

The paper provides an overview of subsidence research which was done by the Sasol Company in South Africa over a period of more than six years. The magnitudes of subsidence elements in South Africa are largely similar to those in the U.S.A. and Australia, as opposed to Europe. The research resulted in a subsidence prediction method with a new approach to the prediction of ground strain. The paper also describes the effects of subsidence on various commonly occurring surface structures such as roads, overland conveyor belts, pipe lines and power pylons. It is concluded that while most structures are not specifically designed to accommodate mining induced displacements, they can nontheless be undermined safely and economically with only minor precautions.

Jan 1, 1986

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019