Search Documents

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By C. E. Golson

The preparation of aggregates is a form of mineral processing which has been taken for granted for many years, mostly because of its lack of glamour when compared to the winning of metallic minerals from their ores. Many of the processes and equipment now used in the metallic mineral processing industries originated in the more prosaic preparation of aggregates. 'Their adaptation to metallurgical processes has led to developments both in their design, and in their use. Modern practice, has been so exacting in its demands that, in many cases, this improved technology is finding new applications in the very industry in which it originated the mineral aggregate industry, The low cost requirements, large tonnage capacities and complex specifications which govern the acceptability of its products have node modern aggregate processing a much different art than it was one or two generations ago. The basic conditions which govern the type and quality of mineral aggregates were presented in an addendum to a paper given at the San Francisco Meeting in 1959 by one of the authors.

Jan 1, 1961

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By Mark A. Krall

The Conda Partnership's Dry Valley Phosphate mine is a thinly bedded, multiple seam, open pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/ dozer operations. The ore that is mined is shipped 32 km (20 miles) by rail to a beneficiation facility which upgrades the ore via washing and calcining. The mine and beneficiation complexes are owned by the Conda Partnership. The Conda Partnership is a joint venture between Beker Industries Corp. of Greenwich, Connecticut, and Western Co-Operative Fertilizers (U.S.) Inc. of Alberta, Canada. The Conda Partnership operates as a separate entity from the two partners.

Jan 1, 1984

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By O. R. Bell

In Australia's remote North West are located the operations of Cliffs Robe River, one of the world's largest iron ore projects. Initial project cost was $US300 million and required the construction of a deepwater port, two toms for 3000 people, a 105 Mw power station and 170 km of railroad, all in harsh, arid country over 1300 km from the nearest industrial centre. The ore occurs as goethite cappings on scattered mesas and averages 57 percent iron. All aspects of the project are reviewed from pre-operational research, through project construction to current operation.

Jan 1, 1979

By B. T. Dawson

In today's work world, constant changes are a fact of life. Downsizing and technological advances are two of the most prominent concerns for employers and employees alike. In this article, the author addresses some of the emotional consequences of these changes and offers a new, empowering perspective for coping with them.

Jan 1, 1998

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By M. J. Raffaldi, K. W. Harris, K. A. Perry

"Highwall miners have been widely used to extract additional coal reserves from existing surface operations, particularly on contour operations in the Appalachian coalfields. Using a continuous miner cutting head, coal may be extracted from significant depths (such as 150 m), leaving behind an array of web and barrier pillars with the purpose of maintaining highwall stability. This method inherently involves elevated risks to both equipment and personnel due to proximity to and increased exposure time near highwalls. As a result, modern operations should actively design web and barrier pillars to maximize extraction while providing adequate stability. The ARMPS-HWM software, an empirical-based program created for the design of web and barrier pillars at highwall mining operations, is one such approach. The calculated stability factor is compared with empirically established guidelines produced from examining case histories.The ARMPS-HWM program is a handy tool for initial design, but understanding the site’s structurally significant geologic features and geomechanical behavior is important and may potentially increase extraction. We created a two-dimensional numerical model using FLAC3D and calibrated it to ensure pillar strength, closely following the Mark- Bieniawski formula for a typical range of pillar geometries and overburden properties. The development of pillar stresses along a highwall panel was then numerically investigated as mining progressed, and the stress distribution between barrier pillars was found to be asymmetric, which can result in an over-design of the closeout web pillars if tributary area loading is assumed. Finally, the importance of adequate barrier pillar stability is highlighted."

Jan 1, 2014

By M. D. Banghart

The Republic of South Africa is an outstanding example of the benefits to a new land by the application of individual enterprise, capital and know-how. While South Africa was colonized by European and Bantu people some 300 years ago, it was only 70 to 80 years agog when diamonds were discovered at Kimberley and gold on the Witswatersrand, that the mining, industrial and commercial potential of the country began to emerge. South Africa s national income rose from R1, 200 million in 1945 to over R4 billion in 1960 (1R = 10 shillings = $1.40 U. S.) The annual national income per head of population -- including all races -- is currently R254 (£127) This compares with £24 for India., £30 for Nigeria, and £50 for Ghana. Allowing for the increase in population, the increase in real income per head of population was about 40% during the past 15 years.

Jan 1, 1962

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016

By J. D. Miller

"It is now possible to use 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site coarse particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining and the processing of industrial minerals. INTRODUCTION Plant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants, and mineral processing plants is needed to improve plant capacity, product quality, and/or process efficiency. Not much on-line coarse particle characterization is done at these plants. Some limited information regarding particle size is obtained on-line from reflected light images using systems such as the OPSA, Split, and WipFrag analyzers. Even laboratory analysis of coarse particles has been difficult because of the large amount of sample required to insure statistical significance of the results. During the past decades laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage [1, 2]. 3D X-ray tomographic analysis had its origin in the medical services industry; it is used to provide internal images of the human body and now has also been developed for non-medical applications [3]. Figure 1 shows a schematic diagram for the cone-beam geometry micro-CT system. In our case X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a three-dimensional image is reconstructed from the collected set of projection images. With the availability of automated high speed X-ray tomography [4] it now seems possible to do plant-site particle characterization at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining, and the processing of industrial minerals"

Jan 1, 2016

By F. L. Pirkle

The mineral zircon is mined for use as specialty foundry sands, abrasives, ores of ZrO2 and zirconium metal, refractories, and zirconium chemicals. It is produced as one of several products from heavy-mineral sand deposits associated with fossil shorelines. Because of its low coefficient of thermal expansion, its high melting point, its high refractive index, and its chemical inertness, it is an attractive refractory material. Zircon varies from deposit to deposit in terms of grain size, grain shape, and chemical impurity. Thus, there is a wide range of commercial products differing in impurity levels, particle shapes, and grain sizes.

Jan 1, 1992