Search Documents

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986

By Christopher Mark

Mines with exceptionally low-strength roof (UCS <3,500 psi and CMRR <40) are much more likely to struggle with roof falls than other mines. Weak-roof is a particular problem for many room and pillar mines in the Midwestern and Northern Appalachian coal basins. Traditional roof support techniques are often not up to the challenge at these operations. This paper focuses on two mines, one operating in the Upper Freeport seam and the other in the Herrin No. 6 seam. Together, the two mines had more than 300 roof falls during a recent 5 year period. Each has experimented with a variety of roof bolt types and lengths, and with different supplemental supports. Detailed statistical analysis was conducted to determine which support combinations have proven to be most effective. Geology, horizontal stress, and time are also important at both mines. Successful control techniques have included; ? Identifying particularly troublesome lithologic roof units; ? Installing longer and stronger roof bolts; ? Installing supplemental support in intersections, and; ? Limiting the duration that a panel remains open. The lessons learned from these mines, and others like them, could help improve ground control safety for the entire U.S. mining industry.

Jan 1, 2004

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By E. Bane Kroeger

In underground coal mining, there is often a need for supplemental support for mine openings. In the past, one of the most common types of supplemental support was wooden posts that were installed against the roof using opposing wooden wedges. Underground, wood has the tendency to shrink from moisture loss and dislodge if not under load. Another drawback to using wood is the variability in strength between posts. Defects in the wood such as knots can cause weaknesses that often lead to premature failure of supplemental support. Many mines that install large amounts of supplemental support in certain areas of the mine such as bleeder entries in longwall mining have switched to using steel props rather than wood posts or cribbing. The reactions of steel props under loading are well- defined and there is little variability in strength between props. Steel props and can be fabricated so they can be used in a variety of roof heights without modification. Wooden posts often have to be cut to a usable length underground before installation. This adds to the installation time of the wooden posts. Steel props are more compact and can be lighter than their wooden counterparts, depending on the length and carrying capacity. Often times it is desirable to prestress the supplemental support to improve roof stability. This is often problematic and time consuming with some types if supplemental support. With these factors in mind, research was undertaken at Southern Illinois University Carbondale (SIUC) to design a new steel roof prop. Several new clamping designs were developed and prototypes were fabricated and tested in the labs at SIUC in the spring of 2003. The designs were modified and refined and the first full-size prototype roof prop was tested in January 2004. With the success of the full-size prototypes, a cooperative research program was established between SIUC and Excel Mining Systems, Inc. to further develop the new prop. Development went smoothly and the prop has performed as expected. In February 2005, SIUC and Excel entered into an exclusive licensing agreement. The prop design under license, the K-Prop, will be installed using a lightweight portable hydraulic jacking system under design that can be used to prestress the props, applying load to the roof and floor during installation. By varying the installation load, the prestress load can be varied from about 1,000 to 10,000 pounds (4.448 to 44.48 kN) and at the same time, the carrying capacity of the K-Prop can be varied from 10,000 to 100,000 pounds (44.48 to 444.8 kN). The K- Prop is composed of only 3 pieces and laboratory testing has suggested that it can be installed by a pair of workers in less than two minutes. The speed of installation of the K-Prop should significantly reduce the total installed cost for supplemental support and should provide a safer working environment by prestressing the prop, which will add support load to the roof and floor during installation.

Jan 1, 2005

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development&apos;. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines&apos; Mine Roof Simulator.

Jan 1, 1995

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed &apos;out of plumb&apos; and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By D. W. H. Su

Following a roof fall in the B12 headgate of a CONSOL Pennsylvania Coal Company (CCPC) underground coal mine in February 1998, CONSOL R&D and Exploration initiated an underground roof geology reconnaissance program along the B13 and B14 developments to define potential roof instability areas and to recommend appropriate supplemental headgate support. This reconnaissance program revealed the presence of a thick, massive Pittsburgh sandstone channel overlying the B13 and B14 panels. Surface and underground core holes confirmed the close proximity and the very massive, nonlaminated nature of the sandstone. To mitigate anticipated adverse conditions at the B 13 and B 14 longwall faces due to delayed caving of the massive sandstone behind the shields, a task force consisting of Operations, Exploration, and R&D personnel was formed in May 1998. Several operational adjustments were made by mine management, including repairing damaged lemniscate links, maintaining immediate forward shield support, and implementing measures recommended by the task force intended to boost the shield set load density at the face. After reviewing available geotcchnical information, the task force also recommended fracing of the massive sandstone over the B13 and B14 panels to enhance caving characteristics and further reduce the bending-induced stresses in the sandstone near the face. Horizontal fracs were created at a horizon about 25 feet above the Pittsburgh seam main bench over the two panels in June and November 1998, respectively. To evaluate the effect of sandstone fracing and operational adjustments on the bending-induced stresses in the sandstone, three finite element models were constructed and analyzed. Results from the finite element analyses indicate that one horizontal frac, 25 feet above the Pittsburgh seam, would reduce the bending-induced stresses in the sandstone by approximately 50 percent, maintaining them at a level below the ultimate strength of the sandstone. Operational adjustments to increase the support set load density and support stiffness could reduce the bending-induced stresses in the sandstone by a maximum of an additional 10 percent. Shield pressure monitoring at the B14 midface confirmed the presence of a lower roof pressure zone inby and outby the 1314 frac holes. This lower face pressure significantly contributed to improving the B13 and B14 longwall productivity and safety. The total production downtime due to bad top at the B 12 face within the interval of channel influence was 30,600 minutes compared to about 3,500 minutes each for the B13 and B14 faces. The average longwall advance per machine shift for the B13 and B14 faces within the channel was about 70 percent higher than that for the B 12 face.

Jan 1, 2001

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors&apos; underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Frank E. Chase

Sacrificial entries, roof slotting, and other tactics have been used to combat high horizontal stresses during roadway development in U.S. coal mines. In Australia, the "pillar extraction on the advance" mining method has been successfully employed as a horizontal stress control technique. The concept of advancing and relieving mine workings through pillar extraction developed from observations that some mines experience difficult ground conditions when advancing and retreating the first panel in a new reserve. However, conditions dramatically improve in subsequent panels. Apparently, the creation of a gob area stress relieves the adjacent panel workings. After much debate and close scrutiny, the first U.S. roof control plan to advance and relieve was approved in 1998, for the Sargent Hollow Mine in Wise County, VA. The major concern was that this mining practice places section personnel inby of the gob. The tentative approval permitted barrier pillar slabbing and removal of the adjacent development pillar during panel development. The intent of the plan was to provide a "stress shadow" for the advancing faces and outby workings to reduce the excessive number of roof falls. Sargent Hollow successfully extracted their first panel by pillaring on advance and retreat mining using posts. Mobile roof supports were employed to extract pillars while advancing the second panel. This paper summarizes Sargent Hollow Mine&apos;s experiences with the advance and relieve mining method.

Jan 1, 1999