Search Documents

By Antonio Huerta

The effects of potassium ethyl xanthate collector and potassium dichromate used as a depressor on a PbS mineral were studied by high frequency impedance technique. Measurements of complex permittivity, at 100 MHz suggested that is possible to obtain from isotherm adsorption the adequate industrial collector concentration being this in the range of lE-3 to 5E-3M of KEX. The e' values (320-420) in the PbS-KEX system was increased as the KEX concentration was lowered). In the other hand the PbS- K2Cr2O7 system showed higher values of e' (420-510) as the K2Cr2O7 concentration was increased. The PbS-KEX-K2Cr2O7 system was evaluated.

Jan 1, 1997

By S. V. Ketov, V. P. Menushenkov, V. S. Shubakov

"The glass samples were obtained by melting of the oxides mixture SrO-Fe2O3-B2O3(Al2O3) at 1200-1250°C with subsequent quenching of the melt on quickly rotating steel roller. Submicronsized Sr(Fe,Al)12O19 particles were formed in glass-ceramic matrix during the crystallization aging of glass. The aging temperature Tag varied in the range 650-950°C. The submicron-sized hexaferrite powder was obtained by removing of the matrix phases using etching. The samples were characterized by X-ray diffraction, scamiing electron microscopy and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10 kOe. The samples of magnets were obtained by pressing of the hexaferrite powder at RT and subsequent aging in the range 900-1200°C. The aged samples exhibit coercivity value up to 8 kOe.IntroductionStrontium M-type hexaferrites have been widely used in technology and industry mainly for production of permanent magnets owing to their appropriate magnetic properties, chemical stability and low cost [1,2]. The SrFe12019-based compounds are characterized by high magnetocrystalline anisotropy and single easy magnetization axis. The highest coercivity is received for monodomain, defect-free single crystal particles with size D - 100 mn. Finely grained strontium hexaferrite prepared by chemical methods such as sol-gel pyrolysis and oxide glass crystallization exhibits high coercivity up to 6-8 kOe [3-5]. Owing to the partial substitution of Al for Fe in the strontium hexaferrite leading to the increase in the magnetic anisotropy field Ha=2Ki/M,, the increase in the coercivity may be received [6]. The notable results were achieved using the SrO-Fe2O3-AlzO3-B2O3 glass crystallization and formation of perfect submicron crystals of alumina-doped hexaferrite [ 6, 7]. The coercive force of glassceramics reached values of up to 10 kOe. Hexaferrite particles are well faceted and have the shape ofhexagonal bipyramids with truncated vertexes [7].In the present paper, we report results of our investigation into the SrO-Fe2O3-B2O3(Al2O3) glass crystallization, hexaferrite powders and permanent magnets, which were prepared by pressing submicron-sized hexaferrite powders at RT and subsequent sintering at 900-1200°C."

Jan 1, 2012

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By S. Castro, P. Alfaro, C. Moctezuma

IMMSA operates a conventional roasting-leaching-purification-electrolysis plant for the production of zinc from concentrates in San Luis Potosi, Mexico. The leaching circuit was designed to take into consideration a feed mixture to the roaster with a maximum iron content of 7%. Since the start-up of the plant in 1982, the zinc recovery increased to 94.5%. However, an increase in the iron content in 1997 caused an important decrease in the global zinc recovery. Two new steps were added to the leaching circuit and modifications were made to the other steps in order to increase zinc extraction. Two new automated press filters were installed to replace the original vacuum drum filters and to minimize soluble zinc losses. Additionally, the residue treatment steps in purification were modified and a calcium removal circuit is just starting operation. These actions, besides improving the operations, have as the main objective to increase the global zinc recovery to levels above 94.5%.

Jan 1, 2000

By Y. Takasaki

For zinc hydrometallurgical extraction, reducing the electric power consumption of the electrowinning process is an important issue for energy savings. At the Zinc & Lead 2000 symposium, the authors suggested that by using the Pb-0.5%Ag-0.6%Ca alloy, the electrolysis energy can be decreased compared to the conventional Pb-0.9%Ag alloy. In this study, the corrosion behaviors of the Pb-Ag-Ca electrode in a sulfuric-acid electrolyte were investigated. Based on the results Or me Pb-0.5%Ag-0.6%Ca anode after 20 days of electrolysis, the bath voltage and the quantity of anode slime decreased compared to the Pb-I%Ag anode. Subsequently, beta-PbO2 on the electrode surface was detected by XRD and its peaks were sharper than the Pb-1 %Ag anode. Moreover, a dense beta-PbO2 layer on the 0.6%Ca a anode surface was observed. Therefore, it was suggested that the dense beta-PbO2 layer on the anode surface is one of the factors that leads to a lower bath voltage and decreasing quantity of anode slime.

Jan 1, 2003

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By Beatriz Ramírez

Xanthates are anionic collectors normally used in flotation devices to modify the hydrophobic surface of sulphide minerals. Xanthates are heteropolar compounds and in aqueous media they dissociate into ionic xanthate and alkali-metal ions; nevertheless their behaviour is not well understood yet. This work characterises the six reactions describing the decomposition of the ionic xanthate in aqueous media by analysing the set of spectra from a UV- Spectrophotometer. Results show the effect of pH on the stability of certain compounds which can be useful to explain the relationships among xanthates and the hidrophobicity of some surfaces (or ions dissolved).

Jan 1, 2006

By Deepak Malhotra

Rosario Dominicana, S.A., operates a gold processing complex at Pueblo Viejo, northwest of Santo Domingo (Dominican Republic). The plant processes approximately 10,000 mtpd of oxide gold-bearing ore with a work index of 11 kWh/mt. The ore hardness has increased to about 17 kWh/mt. Metallurgical auditing of the plant was conducted? to find ways to modify the circuit to process hard ore without sacrificing throughput. In addition, unit operations were optimized to increase recovery and reduce operating cost,. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1989

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

By Daoxin Wu

Originated from(C4H9O)4Ti, nano--rutile TiO2 was synthesized by low temperature hydrolysis process in this paper. After being prepared by decomposing ammonium tungstate and covering on the surface of TiO2, TiO2/WO3 were characterized by means of X-ray diffraction(XRD), UV--vis difuse reflectance(DRS), fluorescence spectrum (FS). Results showed that with the increase of the supported concentration of WO3, the reflectance of DRS and the fluorescence spectrum intensity of TiO2/WO3 decreased accordingly, which indicated the powder?s increase in light absorbance and the decrease in luminescence respectively; with the increase of calcined temperature, the reflectance of DRS increased.

Jan 1, 2009

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000

By Jun Miao, Kang Liu, Jilai Xue, Jun Zhu

CO2 emissions must be reduced by at least 50 % by 2050, and hence the technical solutions to capture and convert CO2 into value–added products should be considered. A Cobalt(III) Schiff base complex (Salen–Co(III)) has been investigated as a catalyst for synthesis of cyclic carbonate from CO2 and epichlorohydrin(ECH) with tetrabutylammonium bromide (TBAB) as co–catalyst. To recover Salen–Co(III) for the next cycling operation, it was immobilized onto zeolite 13X through excessive impregnation method. The immobilized catalyst was characterized using XRD, SEM, BET and ICP–AES techniques. Catalytic tests showed that yield of cyclic carbonate reached 90 % using 0.5 mol % Salen–Co(III) at ambient conditions. The immobilized Salen–Co(III) exhibited better catalytic activity than the homogenous one when used at the first cycle, but the yield decreased by some 20 % after five cycles.

Jan 1, 2015

By R. Boussaa, Y. Fautrelle, K. Zaidat, O. Budenkova, B. Saadi, X-D. Wang, L. Hachani, H. Ben Hadid

"Comparison of experimental data obtained in a benchmark experiment of solidification of a Sn-3%wt.Pb ingot and numerical results of two-dimensional and three-dimensional simulations of the process is presented. The benchmark experiment consisted in solidifying a rectangular ingot of Sn-3%wt.Pb alloy using two heat exchangers. Conditions of solidification were thoroughly controlled due to six thermocouples embedded into each heat exchanger. Due to another array of thermocouples the evolution of the temperature field at a lateral wall of the crucible was registered during the whole experiment. A treatment of the temperature data provided an estimation of the velocity field in the experiment. Post-mortem analyses of the sample provided the pattern of macrostructure of the sample and qualitative segregations pattern. 2D and 3D numerical solidification models are developed to give the distribution of the solute in a solidified sample.IntroductionConvection, either natural or forced, plays a very important role during the solidification. Its intensity and flow pattern affect heat and mass transfer and, consequently, macrostructure and segregation in a solidified ingot [1-4]. The effect of buoyancy convection during solidification has been studied in many laboratory-scale experiments [5-6]. Due to these experiments a general comprehension of formation of various defects in the ingot has been achieved. However, mentioned studies were not consistent since alloys, solidification conditions and configurations were every time chosen arbitrary. That is why the role of each parameter characterizing solidification process remains unclear. Moreover, the question of reproducibility of defects under the same solidification conditions still exists. In addition, most of the experiments suffer from the insufficient knowledge of control parameters that makes difficult their use for validation of models for solidification. These parameters serve as boundary conditions for numerical modeling and their incomplete description leads unavoidably to the errors in simulations. This situation motivated us to develop a setup for benchmark solidification experiments and to perform a set of the solidification experiments which we reported in [7]. Here we presented a comparison between results obtained in a benchmark experiment of solidification of Sn-3%wtPb ingot and its numerical modeling, which was performed in two-dimensional and three-dimensional configurations."

Jan 1, 2012

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999