Search Documents

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Dan A. Mackie

Continuous leaching of precious metals ores in a vat is possible using a jigging technique. This patented method promises to be competitive with heap leaching, particularly in northern climates, difficult terrain, high precipiptation regions, and environmentally sensitive areas. The paper discusses test work to date, plans for pilot plant testing and basic economics

Jan 1, 1990

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By Ann E. Visser

Aqueous Biphasic Systems (ABS) form upon the admixture of certain water-soluble polymers or polymers and salts above critical concentrations, and thus represent liquid/liquid extraction systems whose nature is entirely aqueous. We are currently investigating the utility of ABS (and its solid phase analogs) as "green" alternatives to the use of volatile organic diluents in separations of metal ions. Chaotropic (water-destructuring) metal ions with small negative AGhyd (e.g., Tc04) tend to partition quantitatively to the PEG-rich phase of an ABS, but even hydrated metal cations can be partitioned to the PEG-rich phase if a suitable extractant (e.g., halide, dye, crown ether, etc.) is used to produce a more chaotropic ion-complex.

Jan 1, 1999

By Lawrence D. May, Harry Mudgett

"In the course of developing a new industrial process, information produced at the Research and Development (R&D) stage is critical to determining the technical and economic feasibility of the project. Understanding the fundamental operating parameters for each unit operation in a flowsheet typically comes from historical knowledge of similar systems or by technical development through a robust research program. This approach holds true for processes incorporating fluidized-bed technology. In this paper, the authors will present a practical approach for performing a research study that will allow a process owner to determine if the concept of using a fluidized-bed system can become a reality. Included are discussions of key steps required at each level of the R&D program, and the critical information required for advancing the project to the next stage.IntroductionThe conduct of a research and development program typically starts with a process owner identifying a new industrial need or modification to an existing operation. The owner can pursue this need through multiple routes, including initial in-house development, coordination through an engineering firm, contacting suppliers of key equipment envisioned for the process, or through direct contact with research and development organizations. Where and when the project is conducted is as variable as the number and types of owners who pursue them. Factors that can influence the decision of where to conduct a research program can include the type of process desired, the scale and scope of the project, the location of the project site relative to the R&D options, the experience, capability, and availability of the potential research sources, and the costs to conduct the program. Often, the owner may choose a combination of the available resources to achieve their objectives. In the end, the owner's choice should be based on a thorough understanding of their goals and objectives for the program, and a good understanding of how to measure success while achieving those objectives. Herein, the authors will describe the methods we have typically used to develop the information an owner needs to make an educated decision for investing in a new or modified process."

Jan 1, 2014

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By Mike Dry

While McCabe-Thiele plots are useful for designing single-component solvent extraction systems, not least because of their simplicity, they are less useful for multi-component solvent extraction. This paper presents a relatively simple method, compared to other approaches, for modelling solvent extraction as chemical equilibrium reactions between the various aqueous and organic species. The essence of this approach is how values for the equilibrium constants can be extracted from standard laboratory data. Synergistic solvent extraction of nickel is used to illustrate the method.

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By Bart Blanpain, Muxing Guo, Zhuangzhuang Liu

In order to stabilize free lime in the basic oxygen furnace (BOF) slag to achieve high value products, quartz sand and other additives are injected into slag. However, the current hot stage slag stabilization does not work in case of slag (before treatment) with a liquid fraction lower than 90%, where the slag containing solid particles is too viscous. Therefore, it is essential to understand how solid phases affect the viscosity of the slag system. In this study, the industrial BOF slags were investigated with respect to the correlation between volume fraction of solid phases and its viscosity. Slag viscosity was measured with a rotating type viscometer at temperatures below the liquidus. The volume fraction of solid phases was quantitatively calculated with FactSage. The Einstein-Roscoe equation was employed to predict the viscosity of BOF slag.

Jan 1, 2016

By C. M. Wai

"Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ che1ation-supercritical fluid extraction technique offers several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, B-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.IntroductionSupercritical fluid extraction (SFE) offers several advantages over conventional solvent extraction including the minimization of organic liquid waste generation and exposure of personnel to organic vapors.[1] The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties which make supercritical fluids excellent candidates for extraction and recovery of organic compounds from solid materials [2] Carbon dioxide is a gas of choice for SFE because of its moderate critical constants (Tc = 31 °·C and Pc = 73 atm), inertness, and availability in purified form. After extraction, the fluid phase is depressurized to separate organic solutes from CO2 gas and the gas can be recycled for repeated use. The SFE technology has been applied to industrial scale operations such as the preparation of decaffeinated coffee and hop extracts."

Jan 1, 1996

By Batric Pesic

Calcium silicate slag (Di-Cal) and magnesium oxide condensate (MgO) are the by-products of magnesium smelting operations, As these oxides have acid neutralizing and metal precipitating properties, it was decided to examine their reactions with (a) individual heavy metals and (b) with a mixture of metals in solution, The resulting solid reaction products were further tested with respect to the stability of the contained metals, The stability of the solid precipitates were examined as a function of the method of precipitation and as function of the solution pH With respect to the method of precipitation, the performance of Di-Cal and MgO was compared to the performance of lime, an industry standard for heavy metal precipitation, Four different pH solutions (4,0, 5,0, 7,0 and 1 LO) were used to study the effect of pH on the stability of the precipitates. It was found that Di-Cal, in most cases, produced the most stable precipitates and thus, outperformed lime, Metal precipitates prepared by the addition of MgO were the most soluble for each metal studied, except for Se,

Jan 1, 2001

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Rodney T. Jones

DC arc furnaces were first used industrially for the reductive smelting of chromite fines to produce ferrochromium thirty years ago. Since then, they have been used for a variety of applications, including the smelting of ilmenite to produce titania slag and pig iron, the recovery of cobalt from non-ferrous smelter slags, and the smelting of nickel laterite ores to produce ferronickel. The power of these furnaces has increased from 12 MW to 72 MW for ferrochromium, and to 80 MW for ferronickel. The largest of these furnaces requires two electrodes to carry sufficient current to generate this much power. A review is presented of various DC arc furnaces in use, along with a discussion of the likely ways in which furnace power might be increased further in the future.

Jan 1, 2014

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009