Search Documents

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By James R. Cudworth

OUR colleges and universities have met many difficulties during the past year. From a period of small enrollments and depleted faculties, the educational institutions have passed quickly to a period of the largest enrollments in their history with inadequate facilities and staffs. The results of the shortsighted policy of the Selective Service system which drained the technical schools and universities of many of the students who were potential teachers are now being felt. The movement of faculty members into positions in industry during the war years has resulted in many of them forsaking permanently the educational field for the higher salaried positions they now occupy. Competition is keen between the educational institutions, and between the institutions and industry, for technically trained men. Dean Holbrook's statement in last year's annual review that he thought it would take three or four years to restore our engineering departments to their former level in quality of instructors is even more convincing today. Somehow, the institutions must not only reach their former level in quality of instruction but they must also increase the quantity of their staffs to meet the demands of the ex-service men and the high school graduates for engineering education. The enrollments in the mineral industry fields of mining, metallurgical, geological, petroleum, and ceramic engineering, although greatly increased, are not expanding as much as in the more widely known fields of electrical, mechanical, aeronautical, and civil engineering. In fact, many educators are tremendously worried about the segregation of so many young men in a relatively few fields while the needs of others will remain unanswered.

Jan 1, 1947

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By J. G. Lang

"This paper gives an outline of the principles used in E.M. wire rope testing, showing the practical application of the device and its value in industry and in mining operations.It presents: case histories involving deterioration, such as corrosion, peening and broken wires; anomalies indicating conditions peculiar to drum hoists and friction hoists; tests of locked coil ropes; low-frequency testing; and experiments and development."

Jan 1, 1969

By Sazol Das, Hany Ahmed, Ganesh Bhaskaran, Zhuoru Wu

"Friction stir welding (FSW) process in lap configuration for dissimilar materials has been developed and tested for steel to aluminum joining. A novel cylindrical tool was designed for improved material flow. The joining of steel to high strength 5xxx and 6xxx aluminum was carried out by FSW technique using optimized process parameters. The microstructure, micro-hardness, joint strength and corrosion properties at the weld interface have been investigated. Optical and scanning electron microscopy reveled a well layered structure at the interface and lap shear tests of the welds showed excellent fracture resistance. Neutral salt spray tests for up to 500 hours (ASTM B117) were carried out on the bare steel to aluminum FSW joints, which did not show neither evidence of corrosion at the weld interface, nor any degradation of the weld strength. The FSW lap configuration was applied to prototype commercial vehicle structural component whereby a steel stiffener insert was friction stir welded to high strength 6xxx aluminum alloy. The interface microstructure showed layered root without any steel shattering in aluminum side. A finite element study was carried out to quantify the benefits where it was found that the stiffness increases by 76% under bending loads and 36% in torsion loads.INTRODUCTION Energy preservation and environmental issues, namely carbon footprint and legislation around emission in transportation industries has led to a growing need to use of lightweight materials such as aluminum and magnesium alloys along with various grades of steel in structural application, while still maintaining their strength and crashworthiness. Assembling dissimilar materials within integrated structure is thus a stringent requirement related to optimum performance. In order to achieve an efficient technology of joining dissimilar materials such as aluminum to steel, it remains difficult to select an effective welding process for a given joint configuration. The use of aluminum in transportation industries for structural component is not exclusive in a design and is almost always used along with various steel grades for a mixed materials solution, thus dissimilar aluminum/steel lap joining is of great interest since this is widely used in the assembly of parts (e.g. pillar, frame rails, chassis, body in white (BIW), CAB, etc.)."

Jan 1, 2018

Measurements from an old survey are being machine processed as a pilot project in the development of a computer-assisted method of structural mapping in shield areas. The key element in the system is a field data sheet which requires the geologist to determine a textural hierarchy in each exposure. The pilot system is limited to orientation analysis and utilizes a prior textural analysis, but this would not usually be a problem in utilizing the system ab initio for exploration. A data processing system of this general type offers promise of considerably increased productivity of field geologists by reducing compilation time and improved technical supervision through centralization of processing, and would make structural analysis an economically viable tool in mining exploration and development.

Jan 1, 1969

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By A. D. Huffman

This paper covers the major salt deposits of Canada, with a brief summary of the early history of the industry and a more extended outline of progress since the second world war. Both dry mining and solution mining are covered, and the future of salt mining in Canada is discussed.

Jan 1, 1968

By R. L. Crosby

Microscopical and X-ray diffraction techniques were used to identify two intermediate phases in that part of the solid region of the magnesium-cerium system between and Mg3Ce. Previous literature had reported only one intermediate phase for this region, 1)12t chemical analysis determined the approximate composition of the two compounds to be Mg23Ce2 and Mg17Ce2. The range in composition of the two intermediate phases was found to be limited to less than 0.3 atomic percent cerium. The study did not determine the crystal structure of Mg17Ce2, but that of Mg23Ce2 is tetragonal with a = 10.33 A and c = 19.51 A.

Jan 1, 1966

By G N. Phillips

Global annual gold production has been remarkably constant over the last decade at ~2500 t/a3. The major producers today are China (annual production over 350 t and rising), Australia (250 t), USA (240 t), Russia (200 t) and South Africa (190 t and falling); these figures are representative of recent years but approximate. Demand from jewellery, investment, industrial and dental uses has been in excess of mine production for the last decade, by approximately 1000 t/a.Ongoing exploration is the life-blood for gold mining, and more so than for many other metals. Explorers consider sovereign risk, security, labour costs, commercial terms, land availability and inherent geologic prospectivity to determine where to focus their activities. Exploration success over the last decade has been shared by established major producers like Australia, Canada and USA, several countries in West Africa, and many parts of the Pacific margin. Although gold-only deposits have dominated world gold production historically, the gold-plus types, especially copper-gold, are becoming more important.Australia experienced a major period of exploration success from 1979 that has led to annual gold production rising from 17 t in 1979 to 250 - 300 t/a recently. Today, Australia has economic demonstrated resources of over 9000 t Au, which has risen progressively from 220 t in 1979. The majority of production has come from gold-only deposits in the Yilgarn craton in the southern half of Western Australia, but there are a few large Proterozoic deposits in central Australia including Olympic Dam, Telfer and Starra, which are mostly gold-plus types with copper and gold. Large goldfields in the younger host rocks of eastern Australia include the gold-only deposits of Victoria and North Queensland, and gold-plus deposits of New South Wales.CITATION:Phillips, G N, 2013. Australian and global setting for gold in 2013, in Proceedings World Gold 2013 , pp 15-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S Warden, T Neville, P Leckie

At its simplest, the classification and characterisation of an orebody is a matter of Where, What and When. Where and with what spatial resolution are measurements taken, What properties are measured, and When are the data acquired, processed, and delivered to create the most value. This paper delves into how existing and near-term advances in measurement technologies, field automation, and whole-system-digitisation are combining to open new routes for mine and exploration productivity improvement. Commencing when the initial exploration hole is dug, the advancement in deployment of survey technology—from expert-operated, to driller-operated, to driller-integrated—is used to demonstrate a template for adoption of higher technology measurements. We then introduce and discuss the multi-use measurement as offering outsized returns from a single measurement run, highlighting two new technologies that acquire rock strength while drilling and downhole assay data as examples. For rock strength, we highlight a novel approach to determining Uniaxial Compressive Strength (UCS) while drilling, its relationship to and advantages over Mechanical Specific Energy (MSE), and how it offers utility to multiple downstream processes. For downhole assay, we detail how a back-tophysics approach to Pulsed Fast and Thermal Neutron Activation (PFTNA) analysis offers significant advantages over other measurement methods and earlier implementations of PFTNA, generating a rich data set that can significantly extend and improve the information on which mining decisions are made. Finally, we discuss the possibilities enabled via optimising data delivery, collection, and curation— noting a fundamental limitation of historical systems and exploring the possibilities that will be unlocked by soon-to-market solutions that better enable Orebody Characterisation data to (virtually) move in space and time with rock material post-blasting. Ultimately, the value of optimising the Where, What, and When from point of measurement to the moment it generates maximum value will create greater life-of-asset production for a lower cost and energy input.

Sep 1, 2024

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By DR. DOUGLAS

Discussion of the Paper of Dr. Douglas, presented at the Toronto Meeting of the Institute, July, 1907 (Trans., xxxviii., 455 to 471). EDGAR HALL, Silverspur, Queensland, Australia (communication to the Secretary*) :-Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the side of freedom among the younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms referred to have suffered by their secrecy is their own business-I. bold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to be proved conclusively by Dr. Douglas's own writings. In his paper on The Copper Situation,1 Dr. Douglas says "In comparing iron and copper mining, . . . it must be remembered that 2 tons of average iron ore from the most prolific source now available will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year's production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-ore would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Sep 1, 1908