Search Documents

By L. D. Ricketts

Discussion of the paper of L. D. RICKETTS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 711 to 737. FREDERICK LAIST, Anaconda, Mont.-I am going to tell you of some of the results we have been getting in Anaconda during the past two or three months in a large plant which was finished in May. We commenced work in Anaconda a year and a half ago on the construction of a leaching plant which was to have a capacity of 2,000 tons per day. The plant was to treat tailings from the concentrator, containing about 12 1b. of copper to the ton. During the past year we changed our plans and decided to use the flotation process on the tailings from the concentrator, which contained no oxidized copper, and apply the leaching process only to tailings which had accumulated in a large dump below the works. This dump contains about 15,000,000 tons of tailings, and since some of the copper in it is oxidized, we felt that the application of the flotation process would result in the loss of too much of the oxidized copper, particularly as time went on. In starting up we had a number of difficulties to overcome, as is usually the case. They were not of a serious character. The results obtained, so far, have been decidedly encouraging. During July the plant treated a total of 50,000 tons of tailings, or an average of 1,610 tons per clay. The extraction was about 83 per cent., which, on material of the grade treated, meant a. tailing assaying under 0.1 per cent. copper. The acid consumption was about 65 lb. per ton, and the fuel percentage in. roasting was about 4 ¼ . We expect to cut the fuel percentage in the next month or two to about 3 per cent., the high percentage during July being clue to starting up and shutting clown furnaces. We find that iron builds up in the solution to a marked degree. This is not a serious platter with us, because we have cheap sulphuric acid and can reject solution whenever it gets too foul. The extraction of silver has been remarkably good in the large plant. It has averaged better than 75 per cent. It seems that so long as we maintain salt in the solution to a percentage of 10 per cent., the extraction is good. We allowed the salt to fall off in order to find how low a percentage we could use. At about 7 per cent. the silver extraction fell to 65 per cent. This was to be expected, because silver chloride is soluble in strong brine, but not in weak brine.

Jan 12, 1915

By Gordon W. Parsons, Ross E. Sampson

"THIS PAPER will trace the work done in bringing the Munro underground ""A"" •Orebody into production to replace the open pit, which was scheduled to be completed early in 1959. Included will be an outline of the exploration work and early planning, and of the final decisions on mining methods. Some of the more detailed work will be described and reasons will be given for the decisions made regarding development work, mine ventilation, ground support, and equipment. Brief mention will be made of open pit operations, as these have had some influence on underground development. Also, some of the main geological features of the ore occurrence will be de-scri0bed, as these had to be taken into consideration when making decisions on ore development and mining methods.LOCATION AND HISTORYhe Munro mine of Canadian Johns-Manville is in Ontario, approximately 50 miles east of Timmins and 40 miles west of the Que-bec-Ontari-0 boundary. The producing orebody is in the southwestern part of Munro township. Property controlled by the Company extends nortl1westerly about 2¥2 miles into Beatty township, on which two other interesting asbestos-bearing zones have been partially expl-0red. Active exploration work on the property was started in March, 194.9, and continued until the summer of 1950."

Jan 1, 1960

By Marcus Digre

The autogenous grinding method has been progressively employed in mineral dressing plants during the last 15 years. The term has been used with somewhat different meanings (1), (2), (3). In this paper the author will use it in the most restricted way, for processes where run-of-mine ore (rock) in one step is reduced to a grind product by the action of the ore itself without any other grinding media present. The pebble grinding process where the major part of the ore enters the mill as finely crushed product which is ground further with selected coarse ore pieces acting as grinding media, is not considered autogenous grinding. Processes where a minor amount extraneous media as steel-balls is added to supplement an autogenous mill charge will be called semiautogenous. Other terms need also to be defined. "Mill charge" will be used about the active part of the mill content which performs the grinding, that is the steel balls in ball grinding and the coarse ore pieces in pebble and autogenous grinding. The interstitial nearly finished material is not included in the term "mill charge", and for the wet grinding operations is called the "mill pulp' The term "pebble" will be used for any rounded ore or rock piece in the mill charge whether it is an autogenous or a pebble grinding operation.

Jan 1, 1970

By E. A. Metz

It has been approximately four years since the International Agency for Research on Cancer (IARC) reclassified crystalline silica as a "group one" substance. Since then, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease, and several aggressive campaigns have been developed to increase awareness of silica-dust-related problems in the industrial environment. New analytical techniques are now being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper discusses the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By N Cusworth

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines û mining, metallurgical, chemical, civil, electrical, mechanical and environmental û as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies û and hence no two development projects û are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource projectÆs development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as ædoing a feasibility studyÆ. But the principal purpose of a æfeasibility studyÆ is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant û they are a prerequisite to the demonstration of a projectÆs viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of æfeasibility studiesÆ and provide guidance to minimum standards and best practice.

Jan 1, 2007

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By F. L. Sizer

THE mining regulations of British Columbia and Mexico present some features which might well be copied in the United States, if we are to have a complete revision of the laws governing mining titles. 1. First and foremost is the "square" location, which would mean the abolition of extralateral rights. This is a condition in both of the countries above named which has seemed to work no hardship upon any one, and certainly the limitation of underground rights by vertical planes through all lines makes a locator's rights clear. In view of the long and costly litigation which has involved so seriously many of our most important mining districts, it would seem to be the part of wisdom to avoid a repetition of similar trouble on titles of lode mining claims, by the enactment of a law similar to that in force in British Columbia. Objections have been raised by representatives of English companies to the investment of large amounts of money in mining operations in the United States, because of the insecurity of title under the present apex law; and the statement has been made to me personally by one of the largest English operators, that he would never again consent to the purchase of mines in the United States, preferring Mexico with all its revolutionary troubles to the danger of encroachment upon his underground rights by an unscrupulous neighbor. Without going into further argument as to the desirability of the "square location," it should be sufficient to say to those who are inclined to "let well enough alone." and still stick to the "law of the apex" that there have never been any serious objections raised to this feature of the square location in either British Columbia or Mexico. There are well founded and logical reasons for abandoning the doctrine of extralateral rights since it is so difficult of interpretation; the most natural substitute being a law similar to that of British Columbia, giving to each locator an area 1,500 ft. square.

Jan 3, 1914

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By R. S. Bradley

WHAT are known as insulating firebrick are lightweight firebrick with low thermal conductivity designed primarily for use in direct contact with furnace gases. These are a recent development in the refractories industry, and are really an outgrowth of the type of insulating brick suitable for use behind refractory walls developed by the insulation manufacturers. To differentiate between these two types of brick, the manufacturers have recently agreed upon the use of the term "Insulating Firebrick" to apply to the type of brick suited for use in direct contact with furnace gases, and the term "Insulating Brick" for the type suitable for use behind refractory walls. Insulation was applied to steam pipes as far back as 1900. This was a low-temperature insulation, the most common type being magnesia blocks. The next development was applying insulation to the outside of furnace walls, a service which necessitated an insulating material of higher temperature resistance. Natural diatomaceous earth, both in the powdered and brick form, was used; this was efficient and is still used extensively for backing up refractory walls where the inner surface temperature of the insulation does not exceed 1600° F.

Jan 1, 1937

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By W Stange, N Hanson

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction û primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007

By Robert L. Sundeen, Richard V. Wenberg

Service vehicles, often called support vehicles or auxiliary vehicles, are used in secondary functions to support production activities such as loading, drilling, and timbering. Probably the most common support vehicles are the personnel carriers used to move miners to and from work areas. Utility designs are used to transport supplies and various less mobile equipment. Specific application designs are used for special work such as explosives transportation and loading, equipment maintenance, and equipment lubrication. PERSONNEL CARRIERS Personnel carriers are available in a wide variety of sizes and configurations. Some are two-wheel drive, though most are four-wheel drive. Smaller versions carry at least two men and usually have sufficient capacity to carry a small payload of supplies or equip¬ment. The American Motor's 05 Jeep, equipped with an optional diesel engine, has been adapted successfully for this light duty. Larger personnel carriers with ca¬pacities of 12 to 20 or more men currently are available, as shown in Fig. 1. The designs often are customized to the operating characteristics of each mine. All meet the latest federal requirements for rollover protection, emergency brake systems, etc. UTILITY VEHICLES Utility vehicles are adaptable to numerous duties. Probably the most common are ordinary haulers with a flat bed or low-sided box. They are used for hauling supplies and equipment from one point to another. Some occasionally are used for towing and may pull one or more trailers. Fig. 2 shows a typical utility truck. SPECIAL-APPLICATION VEHICLES Special-application vehicles are possibly the most important of all support types since these vehicles di¬rectly support and maintain production equipment. Such vehicles are available in a wide variety of sizes, mechanical functions, and operating specifications. Most versions are four-wheel drive and articulated. Among the more common vehicles are explosive haulers and loaders, mechanic's trucks, lubrication trucks (Fig. 3), and special carriers. TYPICAL APPLICATIONS Development Utility haulers are essential in trackless operations to bring supplies to advancing headings. Some utility haulers may be dedicated to bringing in steel sets and may be equipped with boom lifts to unload heavy sup¬ports or even place them as required. A rockbolt hauler may have a boom-mounted operator's basket which can be used for bolt installation or inspection. Various mechanic's trucks and pipe trucks service the heading to keep power, air, water, and ventilation at the face and to keep face equipment at maximum utilization. Production Production operations require a variety of support equipment. Because of the larger crew size brought about by the addition of the production force, personnel carriers play a greater role. Correspondingly, steel¬support hauling equipment and bolting trucks usually see limited application. PRODUCTION UNITS Capacity Personnel carriers are available to carry almost any number of people desired. Likewise, other types of carriers or haulers can and are built to fit specific re¬quirements. Physical size, capacity, and operating char¬acteristics can be varied to fit any size of opening and operating condition. Generally, articulated models offer greater maneuverability than straight frame-axle steer designs. Most vehicles of this type are lower in power than production units, generally under 74.6 kW (100 hp). Operating performance still compares favorably to that of production equipment, i.e., the support vehicles can travel at equivalent speeds on the various mine gradients. Manpower Auxiliary vehicles should require only a single opera¬tor. Specific application vehicles may require more than one person. For example, ventilation trucks usually require a crew of two where pipe must be installed.

Jan 1, 1982

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010