Search Documents

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By David L. Veith

This Bureau of Mines bibliography of U.S. and Canadian literature pertaining to revegetating coal-mined lands contains 805 references published from 1977 to 1984. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate only those dealing with the coal mining region and subject of interest. All references are annotated. Other sources of information are given, including Office of Surface Mining (OSM) and State reclamation agencies and other published bibliographies.

Jan 1, 1985

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By M Flis

The Razorback Iron Ore Project is a high tonnage, low-grade magnetite deposit that defines a new iron ore district in South Australia. Known since the 1960s, the deposit has come into its own as the iron hungry world demands not only larger tonnages, but higher grade and cleaner magnetite concentrate ores that counterbalance the increasingly dirty haematite ores that are coming into production.Razorback is hosted by the Neoproterozoic Braemar Iron Formation, a tillitic unit that is part of the Adelaidean Geosyncline sedimentary sequence. At Razorback, this formation forms the southern limb of the Pualco Syncline, dipping at 42° to the north and outcropping along a prominent ridge. The formation consists of a series of alternating bedded tillitic and interbedded magnetite units that represent cycles of glacial advances and retreats. Seven cycles, resulting in seven stratigraphic members, are recognised. Members B, D, and G are the thickest, at 30 - 70 m each, and are the target of current investigations. While the bedded magnetite has the highest iron content, typically 35 per cent Fe, the tillitic unit, at typically 26 per cent Fe, has similar iron content in the ground mass but is diluted by the inclusion of iron-poor granite and metasedimentary dropstones. The mineralisation forms a simple dipping tabular body with only minor faulting, folding and intrusives. Grades, thickness, dip, and outcropping geometry remain very consistent over kilometres of strike, presenting an excellent mining proposition.Razorback differentiates itself from other Australian magnetite projects in a number of important ways. It is not a banded iron formation (BIF); it will have low crushing and grinding costs; and it is located in an infrastructure-rich area close to open-access, high capacity rail, to a selection of ports and to gas, electricity, labour and engineering services. Royal Resources has announced an Inferred resource of 277 Mt @ 25.9 per cent Fe. The company is targeting a resource of 500 - 1000 Mt to support a 10 Mt per year concentrate production. Davis Tube Recovery work shows that the ore is capable of producing a concentrate of over 68 per cent Fe with very low deleterious elements. Metallurgical testing confi rms the ore is soft, and with near-zero initial stripping ratio the project will have a low opex. With access to existing critical infrastructure, capex will also be low, ensuring Razorback will be a highly competitive iron producer in this emergent mining district.

Jul 11, 2011

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By L Dyer, A Keith, G D. Corder

As mining activity moves to remote and less developed locations globally, a holistic approach to mine development is fundamental for achieving a balance between strong financial returns and corporate social responsibility and transparency. Key inter-related fundamentals such as social licence to operate, life-of-mine operational planning, minimising environmental impacts and, most importantly, attractive investment returns for the mining company all contribute to the viability of any new mining project.However, the typical practice in the mining industry is often to treat environmental and social/community aspects as separate compliance issues that are dealt with at minimum cost and disruption to the project and resulting operation. This often results in less than optimum environmental and social outcomes, and presents considerable liabilities at the time of closure when rehabilitation programs continue to require funding when all revenue has ceased.The five capitals model seeks to identify each of the key contributors to sustainable development as financial, manufactured/physical, social, human and natural to formulate a type of triple bottom line approach balancing these often competing project factors. The SUSOP® sustainability risks and opportunities framework, developed by the mining industry, bases its approach on the five capitals model and proposes an approach that breaks down enterprise silos to identify innovative solutions for life-of-mine sustainability. This framework has been developed with the nature of mining projects in mind in order to produce approaches and outcomes relevant throughout the life cycle from the planning phases, through project design and construction into operation and closure.This paper argues the need for a more holistic approach to the development and operation of mining projects, and presents case studies where a holistic approach has been applied, in whole or part, and discusses the lessons learned from these case studies.CITATION:Corder, G D, Keith, A and Dyer, L, 2014. A capitals based approach – leading innovation in planning for life-of-mine sustainability, in Proceedings Life-of-Mine 2014, pp 499–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By R. Barbaroux, J. -M. Lalancette, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"Arsenic released from the lithosphere by mining and metallurgical activities is a growing global environmental concern. Dundee sustainable technologies (“DST”) has developed a processing technology to sequester arsenic by means of vitrification. This method can effectively sequester arsenic trioxide without the need to oxidize from As (III) to As (V). Arsenic oxide is incorporated within a silica glass matrix that is stable as per the Toxicity Leaching Characteristic Procedure (“TCLP”) or EPA Method 1311. In this paper, the conventional treatment of arsenopyrite, commonly referred to as “two-stage roasting”, is discussed along with the options traditionally available for the remediation of the arsenic trioxide by-product. The drawbacks limiting the adoption of this processing flowsheet are discussed and a new processing route is presented for the treatment of arsenopyrite. This new flowsheet outputs an auriferous aluminosilicate highly amenable to gold extraction (> 96%) while eliminating the sulfur dioxide production associated with the second-stage roasting of pyrrhotite and ultimately uses vitrification as a definitive sequestration solution to arsenic trioxide.INTRODUCTION Faced with the depletion of conventional gold ores, the gold industry has witnessed a trend towards the exploitation of arsenical deposits. Arsenic is a naturally occurring metalloid often found in mineralogical association with gold. Many northern Canadian regions, from the Northwest Territories to Northern Manitoba, Northern Ontario and the Abitibi region are facing significant arsenic challenges. Projects are deemed uneconomic or prevented from going into operations due to the costs associated with handling arsenic material and there are penalties imposed to complex concentrates by smelters. In addition, Canadian mining operations have left an environmental legacy of gold tailings with grades typically of up to 9 grams per tonne with no processing solution as they also contain significant arsenic contamination at grades of up to 20%. Table 1 presents a list of Canadian deposits known to contain arsenic."

Jan 1, 2017

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015