Search Documents

By C. H. Tiernon

"This paper was' prepared to emphasize the part that coal washing tables can play in the development of many of the reserves of coking coals in Western Canada_ It covers a brief history of the development of the coal washing table through the present third-generation unit, which suspends from overhead steel beams and is driven by a counter-rotating gear mechanism. The design and operation of this unique table are covered in detail.An analysis of actual operating data is included, with explicit statistical breakdowns of the table products. The data used were actually produced by operating coal companies, and also produced by the United States Bureau of Mines while gathering data for a research investigation. Table feed capacity is discussed, as well as performance criteria and the parameters of relative table performance. Several typical table flowsheets are described, emphasizing the specific reasons for their use. The paper covers the past and present value of the table to the United States coal industry, and makes mention of the newest addition to the family of suspended, multiple-deck, counter-rotating, gear-driven, coal washing tables, the CONCENCO ""88"" Deister table."

Jan 1, 1973

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By S. M. Runke

An earlier Bureau of Mines report4/ reviewed and summarized all reports of investigations dealing with the coarse grained pegmatites of the Black Hills of South Dakota to dune 1951. It was proposed, and the hope was expressed in this report, that future progress in the development of the technology of the mining and beneficiation of the pegmatite deposits would be rapid enough to make it possible to issue annual progress reports. Although notable progress has been made in the treatment of pegmatite material, it has not been rapid enough to justify annual reports

Jan 1, 1954

By John Hickey

Management teams at mining companies begin to ask themselves whether to take a company public and, if so, how to do it as they approach the normal threshold for going public in terms of revenue and operating performance. Today, the expense of going public generally suggests the company has at least $20 million in annual revenue and at least $2 million in cash. The revenue number can be lower for mining companies with large reserves. In order to properly attract the investing public, the company must also be operationally strong with robust prospects. The company should have a strong management team and a consistent history of double-digit growth that will continue into the foreseeable future. Assuming the thresholds are met, a company?s management needs to weigh the pros and cons of going public.

Jan 1, 2012

By E. Govender-Opitz, L. Lelia

The South African mining industry plays a significant role in the economy of the country. Nonetheless, the negative impacts on the environment continue to prevail. In regions where mining exists in proximity to communities, mining activities have led to the disruption of modality. Rural communities are mostly affected as they depend on land use for agriculture to sustain their livelihoods. The conversion of land for mining activities often leaves the communities vulnerable when mines close because of the limited life span of mines. An ongoing discourse focuses on how the mining industry can contribute to sustainable development of the communities in which they operate. Post-mining transformation offers an approach for the mining companies to contribute to sustainable livelihoods post-mine closure by strengthening rural-urban linkages, which ensures inclusive development of both rural and urban areas. The paper employs a case study approach to Richards Bay Minerals and the adjacent rural communities of Sokhulu and Mbonambi. It sets out to understand the post-mining transformation employed by RBM and explore the rural-urban linkages that manifest as a result. Findings show that sand dune rehabilitation employed by RBM is successful in restoring soil fertility and establishing the natural ecosystem. The casuarina planted to rehabilitate the dunes is used to spur an alternative charcoal industry post-closure. The main rural-urban linkages that manifest are flows of people due to job opportunities and flows of goods from the sale of charcoal produced. However, there is a lack of communication and lack of authority to ensure responsible management of the casuarina plantation and equitable sharing of benefits. The paper recommends that other post-mining transformation strategies such as eco-tourism should be explored and that the government, at both national and local level, the community and the mine should be involved to ensure overall success and sustainability of the strategy. Keywords Post-mining transformation, rural-urban linkages, alternative land use

Jan 1, 2020

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man's varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930's when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years' duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry's basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada's historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country's major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

Prof. Henry S. Jacoby, Cornell University,Ithaca, N.Y. (communication to the Secretary): When a simple beam supports any given load, the lower fibers me in tension while the upper fibers are in compression, and if its cross-section is rectangular the neutral surface, where the stresses pass through zero from tension to compression, is at mid-depth, provided the elastic limit is not exceeded. In addition to the longitudinal stresses, there are horizontal shearing-stresses between the fibers which have their maximum value in the neutral surface, and which equal zero at the upper and lower surfaces, while there are also vertical shearing-stresses. Let another beam of the same dimensions be placed on top of this one, and the load be doubled, it then produces stresses in each beam of the same character, magnitude and distribution as in the preceding case, provided there be no friction between the adjacent surfaces of the beams. Next let these two beams be so firmly united that there will be no motion between them when the same load is again applied. All the fibers in the upper beam are now in compression, and those in the lower beam in tension, while the maximum stresses in the outer fibers are only one-half as large as before. The strength of the combined beams is therefore doubled. If, however, some motion occurs between the beams, then the stresses in some of the lower fibers of the upper beam pass from compression to tension, and those in some of the upper fibers of the lower beam from tension to compression, while the stresses in the outer fibers have a magnitude between the two values previously stated. These fundamental facts relating to the flexure of beams indicate the necessity of carefully designing the keys or brace-

Jan 1, 1898

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By M Runkel, J Hammerschmidt, A Holmstr÷m, A Charitos, J Gnntner

"Roasting of sulfide concentrates and refractory ores is an important process step in the production of metals and chemicals. Sulfides of iron, zinc, copper and other metals are oxidised with air between 600 and 1000¦C into metal oxides or sulfates and gaseous sulfur dioxide. Roasting of gold concentrates and ores is a typical processing step used to produce a porous calcine suitable for cyanide leaching. During roasting, elements posing problems are removed through: oxidation (carbon, sulfur, arsenic and antimony) or volatilisation (mercury, chlorides and tellurides, as well as arsenic and antimony).This paper focuses on the environmental aspect of roasting using fluidised bed technology. The approach is to show that roasting is an attractive solution for refractory ore pretreatment since, on the one hand, it is an efficient technique yielding high gold recovery rates, while on the other it is able to comply with current stringent international environmental regulations. In that respect, roasting is compared to alternative processes, ie pressure oxidation (POX), bio-oxidation (BIOX) and ultra-fine grinding (UFG). Roaster high gold recovery rates are ensured through roasting-leaching test work, which allows the derivation of respective roasting parameters that are easily achieved in an industrial plant. On the other hand, key elements of the roasting process are analysed, which make it an efficient and sustainable technology, ie the possibility for energy recovery, the removal of off-gas impurities during the different gas cleaning steps (handling of arsenic, mercury emissions and further hazardous dust and gas emissions) and the treatment of the SO2-gas in order to produce sulfuric acid, and finally the treatment of the effluent produced. The processÆs environmental aspects are summarised by listing roasting emission values that comply with international regulations.CITATION:Charitos, A, Runkel, M, Gnntner, J, Holmstr÷m, A and Hammerschmidt, J, 2013. Roasting - a study on environmental aspects, off-gas, effluents and residue treatment, in Proceedings World Gold 2013, pp 509-518 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By Xinhua Wang, Qiangqiang Wang, Yubin Li, Shusen Li, Lifeng Zhang

"Numerical simulation on the fluid flow in a Flow-Control Mold (FC-Mold) were performed. The motion of inclusions were calculated. With FC-Mold, the flow pattern and surface velocity become more symmetrical, and at higher casting speed the velocity of liquid steel in the top region of the mold was largely reduced with the highest velocity of the meniscus reducing from 0.65 mis to 0.4 mis, and the meniscus shape became flatter. With FC-Mold, more inclusions approached to the surface of the slab and the amount of inclusion in the center of mold became fewer. Larger inclusions were easier to remove, however, the EM filed of the FC-Mold could hardly improve the removal of inclusions from the molten steel.IntroductionElectromagnetic brake technology is an effective method to control the flow pattern within continuous casting mold, together with other casting parameters, nozzle design and mold geometry [1-5]. Due to the interaction between the applied magnetic flux and the conductive molten steel inside the mold cavity, a force is generated in the direction opposite to the jet flow, which can decelerate the high speed steel jet from the SEN ports. The potential benefits include fewer surface and internal defects, fewer inclusion especially at higher casting speed. However if used imperfectly, electromagnetic forces can have opposite effect [6]. Numerical models are the best tool to optimize electromagnetic flow control. In the current study, numerical simulation was performed to investigate the flow field in a continuous casting FC-Mold, and the effect of different operation parameters on the flow, surface level and velocity in FC-Mold were discussed."

Jan 1, 2013

By George M. Fowler

EVERY year it becomes more difficult to find new mining districts and new ore deposits. Nearly all of the important discoveries so far can be attributed to surface manifestations overlying the ore deposit. In the future greater skill will be necessary to find ore deposits that give little or no indication of their presence. Mining geology is making progress by broadening its attack upon mineralized regions, by including in its investigations studies of the relation of physical-chemical processes to ore precipitation and various phenomena that heretofore have not always been looked upon as major factors in the problems. Such, for example, are petrographic peculiarities that will help determine structure, aspects of strata or formations favorable or unfavorable to structural deformation or mineralization, and renewed studies of chert and dolomite. This broadening attack is not necessarily being directed to the study of large areas, but rather by doing extremely detailed work in three dimensions in relatively small critical areas to find the key to the structure, reasons for the manner of rock deformation, composition and texture of the rock, and other con¬trolling factors in the larger areas.

Jan 1, 1935

By Oliver Bowles

ASBESTOS is a name applied to a group of naturally fibrous minerals. As indicated in a later section devoted to a detailed discussion of the early history of asbestos, the tern may be defined as a. fibrous form of serpentine or amphibole. It does not include fibrous forms of other minerals, such as wollastonite, nemalite (fibrous brucite), or the fibrous forms of calcite or gypsum. A material that has the characteristics of silk or cotton and at the same time will not burn is unique. Because it combines these qualities with other advantageous properties, asbestos has specialized uses for which no substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products and their manufacture constitutes a vast industry. The United States leads all countries in the manufacture of asbestos products. The value of such commodities manufactured in 1952 exceeded $332 million. They are not only of vast importance to budding construction and industry but axe absolutely, essential to certain important fields of use, for example, steam packings and friction materials, such as brake-band linings on automobiles.

Jan 1, 1955

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By D. N. Madge

The use and development of industrial process control computers in the mineral industry during the 1970's has been sluggish. This cautious approach is due to lack of commitment by senior management. The lack of commitment is due to several reasons: variable mineral processes and technologies, market fluctuations, and excessive costs and inadequacies of applicable products supplied by computer vendors.

Jan 1, 1979

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937