Search Documents

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

JAMES A. BARR Consulting Engineer Mt. Pleasant. Tennessee Washington. D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Callf.

Jan 1, 1952

[JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Montieello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

JAMES A. BARR Consulting Engineer Mt. Pleasant; Tennessee Washington, D.C. BEHRE DOLBEAR G COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia LENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.

Jan 1, 1952

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2016 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY), and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2016 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported. The SNL data summarize budget estimates for worldwide exploration activities in 2016 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup platinumgroup metals (PGMs) and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash) and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2016 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data and government-funded exploration activities."

Jan 5, 2017

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By Soule&apos, John H.

Although known since 1902, the Capitan iron deposits have not been tined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-4, visited the property; as a result, preliminary sampling of the property was done in 1943.2/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944. Equipment available at that time was limited in the depths that could be reached; and as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.

Jan 1, 1949

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By G. J. S. Govett

World mineral production is dominated by six countries - the U.S., the U.S.S.R , Canada, South Africa, Australia and China - which also hold most of the reserves of the world?s minerals. For the developed and centrally planned countries, there is a strong positive correlation between the mineral production of a country and its land area: there is no correlation between mineral production and land area for the less developed countries. These facts imply that, after taking due account of geological controlling factors, a country may expect to produce minerals in approximate proportion to its land are a provided that political, economic, and historical factors are conducive to mineral exploration and mining. Contrary to popular political belief in many parts of the world, the developed countries are the major source of mineral imports for the industrialized countries. Moreover, exports of ores and minerals account for a relatively small par t of world trade, and are an important factor in the export picture of only a few of the less-developed countries. The looming resource confrontation between the developed and the less-developed countries is based largely on the false premise that the industrialized countries of the world are minerals-poor and owe their wealth to cheap minerals from the less-developed countries. The data presented refute this. Geological controls are relatively minor in the present distribution of world mineral production; political and economic factors are dominant. It is argued that an expansion of world trade in minerals - based on increased exploration and new forms of finance for mining ventures - rather than cartels, price-fixing and trade restrictions is by far the preferable solution to the problem of redressing the legitimate grievances of the poor countries of the world.

Jan 1, 1977

By Donald B. Lindsay

This report presents the findings of an investigation into the characteristics of a number of techniques for cleaning ambient air with special emphasis on their applicability to the removal of the short-lived radioactive decay products of 222-radon, the so-called " radon daughters" that have been identified with the induction of lung cancer in underground uranium miners. The purpose of the study was to review the requirements for control of radon daughter concentrations in mine air, and to examine all techniques whose feasibility has been demonstrated in principle and which in our judgment would be capable of meeting those requirements. The study has included a review of all pertinent literature, both technical and proprietary, on the subject of the control of miner exposure to the radon daughters and in the area of potentially applicable air cleaning technology. Information about the nature of the problem and about the experience of the uranium mining industry in applying air cleaning methods to its solution was obtained by visiting mines where such methods are in use, and by written correspondence and telephone conversations with other industry sources. Information on performance characteristics and costs of applicable air cleaning methods and equipment was obtained from the experience of our own engineering staff and by visits, interviews, and correspondence with manufacturers of industrial air cleaning equipment.

Jan 1, 1978

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915