Search Documents

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By D. Randolph Berry

This report describes a study to develop a detailed set of guidelines and equipment recommendations to be used as a guide for mine operators, mine inspectors, and equipment manufacturers in implementing the emergency escapeway standards for metal and nonmetal underground mines. It was sponsored by the United States Bureau of Mines. The first part of this report reviews the historical background of metal and nonmetal mine fires and the development of present and proposed mandatory standards. This is followed by a discussion of the survey of representative mines and how the proposed standard effects these mines. The remainder of the report covers technical discussions of each escapeway component including a comprehensive computer simulation of mine evacuation. Following the technical discussion of each group of escapeway components is a list of the pertinent guidelines. The major escapeway components discussed are the following: Escaperoutes Refuge Chambers Hoisting System. Escapeway Signs Ventilation Fuel Storage Fire Retardants Warning Systems Auxiliary Transportation

Jan 1, 1976

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

The Menominee Range of northern Michigan was a major producer of direct shipping iron ore for nearly a century. When the last underground mine on the Range ceased operation in 1978, it marked the end of an era. For since the start of mining in the early 1880's the district has gone through a Lull cycle from the start-up of mining through close-down. During this period over 200 million long tons of iron ore were produced and shipped from nearly 100 mining operations. This development and production spanned the time from when the United States advanced from an essentially rural-agriculatural society through the industrial revolution and into the beginnings of the computer and space age. There are many lessons that can be learned from such a rich history. This report attempts to provide ouch a lesson. Through the use of case histories, deficiencies in past mining practices and mine closure procedures that have resulted in current mine related problems are documented. These problems -an be grouped into three areas; 1) subsidence 2) hydrological or drainage problems and 3) problems related to inadequate mine shaft sealing and capping practices.

Jan 1, 1983

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By Ferron A. Olson

Natural bornite (Cu5FeS4) leached in ferric chloride or in sulfuric or hydrochloric acid solutions with oxygen showed several differences. In ferric chloride 80 of the copper was leached in two stages. The first (30 copper removal) requiring one minute was controlled by mixed kinetics (liquid ferric ion diffusion and chemical surface reaction). The second was controlled by formation of a surface sulfur layer and then diffusion through the sulfur. With oxygen in sulfuric acid reaction was slow and only the first stage was studied. Copper removal had an induction period. The bornite structure disappeared at 12% copper removal (also found with ferric chloride) and covellite formed on the surface with a species inside the particles having an x-ray structure similar to CuFeS2 but with composition Cu3FeS4 (also with ferric chloride). Copper removal was controlled by iron dissolution. Surface iron vacancies filled with Cu+ to give CuS while interior copper dissolution produced Cu3FeS4. Preliminary results with oxygen and hydrochloric acid showed 80% copper removal and sulfur as end products (similar to ferric chloride).

Jan 1, 1982

1.1 DEVELOPMENT OF INDUCTANCE MATRICES The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available either from handbooks or from the manufacturer's published data. Thus, it is useful to summarize the derivation of the origin of the inductance matrix from basic principles. 1.1.1 Flux Around a Cylindrical Conductor The flux pattern around a cylindrical current carrying conductor can be found by using symmetry in conjunction with Ampere's Law. From symmetry it is clear that the flux lines which always close on themselves must be concentric circles. Thus, from symmetry alone one can get a qualitative picture of the magnetic field. This is shown in Fig. 1.1 where the inner circle represents the solid round conductor and the outer circle represents a flux line. The quantitative picture will now be developed using Ampere's Law.

Jan 1, 1973

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By W. E. Schroeder

Two underground installations of the sprayfan system are described and evaluated. The spray fan proves capable of reducing by 1300 percent downtime due to high methane. Spray fan face ventilation at 20 ft brattice setback is shown to give improved methane control over conventional sprays at 10 ft setback. In addition, this report describes: ? A simple method for determining the most economical application of ventilation for face methane control ? The effect of place variables (primary ventilation, auxiliary ventilation, seam height, etc.) on methane concentrations ? The correlation of methane concentrations with brattice setback. These results are utilized to suggest a safer and more economical approach to face methane control.

Jan 1, 1981

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977