Search Documents

By Walter E. Vanderpool

Three drilled foundations for an elevated water-tank were instrumented, tested and monitored during construction and the first two years in service. One shaft was load tested by the Osterberg method. A void was detected in one shaft by cross-hole sonic logging, pulse-echo logging and concrete coring. The void was instrumented, hydrostatically tested and pressure grouted. The shaft was ?abandoned? and replaced by two smaller shafts with a straddle beam cap. One of the replacement shafts and the cap were instrumented. The strain that appeared in the abandoned shaft, the replacement shaft and the cap were monitored during the remainder of the construction, through the commissioning test and the first two years of service. The results demonstrate the precision and sensitivity of the vibrating wire strain gage.

Jan 1, 2004

By E. D. Doney

The Kerr-McGee Coal Corporation's Galatia Mine's first longwall mining system was implemented on May 3; 1989. Start-up of the longwall face represnted the successful conclusion of an effort begun nearly four years earlier. This paper-presents a case history of the processes that led to the longwall's implementation, and the subsequent mining of the first 7,900 foot long panel.

Jan 1, 1990

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By Albert H. Fay

The first data compiled by the Bureau of Mines relating to coal- mine accidents in the United States were published in Bulletin 69," in which the total fatalities by years and States were tabulated from 1896 to 1912. Since the publication of Bulletin 69, further research has been conducted, with the result that the bureau is now able to publish for the first time all of the fatal accidents described in the State inspectors' reports by States, causes, and calendar years, from the beginning of inspection service to date. For the anthracite mines of Pennsylvania, there is a continuous record since 1870; the records of the Pennsylvania bituminous mines are continuous from 1877, and, with the exception of one year, the Ohio records are complete from 1874 to date. In fact, the records of all of the States, with few exceptions, are complete; and incomplete data for any year may generally be attributed to the fact that no report was published during that year. The magnitude of the coal-mining industry in the United States is such that too much stress can not be placed on the need of safeguard- ing the three-quarters of a million men employed. Although the figures given herein show an appalling record for past years, they are not published for the purpose of proclaiming the high fatality rate of the past. They are a record of experience covering a period of 45 years, showing causes and results of many accidents in the coal mines of the United States. They represent a diagnosis of the hazard of the mining industry, pointing out the principal physical causes of accidents, and make available a body of uniform facts that will serve as a basis of preventive measures for use in future operations. It is with these great purposes in view that the Bureau of Mines presents the classified data in this report. Classification and study of mine accidents on the basis of number of persons killed is common and very old, but fails to throw enough light upon the problem involved. Many serious accidents in mines have no fatal results, hence in a tabulation of fatalities they are overlooked and the real hazard of the industry is not made clear. An accident does not necessarily include an injury that may result therefrom. Such accidents as the breaking of a hoisting cable, an explosion of powder, gas, or dust, a runaway car or motor are all serious. Although no loss of life results, they should be recorded, investigated, and studied to prevent their repetition. No accurate data for the United States are available showing how far the personal element as related to the miner and his co-worker, the mine foreman, or to the superintendent and others in authority, contributes to accidents. Many accidents are due to inexperience on the part of the miner, his failure to heed orders, a misunderstanding of instructions and last, but not least, carelessness of himself or his fellow worker. A foreman or superintendent may fail to give proper warning regarding the conditions of certain parts of the mine; he may not have inspected certain rooms or entries on the day of a mine accident; the mine may not be properly equipped, or the operator may neglect to comply with the inspector's recommendations. There is, therefore, a personal element on the part of both the operator and the miner that must be considered. Legislation and the enactment of compensation laws will make the operator realize the seriousness of the mine-accident situation, when fatalities and injuries are to be paid for in legal tender of the realm. The miner must be educated and made to realize the dangers he encounters; he must learn that self-preservation and the safety of his fellow workmen should receive his first attention; he should cooperate with his employer, his asso- ciates, and the State mine inspector to the end that the mine hazard may be reduced to a minimum. "Cooperation for safety" should be the watchwords of the operator, miner, State inspectors, and all others in any way interested in the mining industry.

Jan 1, 1916

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

Researchers, medical organizations, statisticians, and others often use data on the nature and rate of occurrence of occupational diseases in directing their efforts and plans. Very often this information is developed from the reports of the States which describe the nature of work¬men's compensation claims and awards and the frequency with which they are made. To be meaningful, the statis¬tical information must be viewed in the context of the State laws involved. There is considerable variation among the laws of the different States. The Bureau of Mines has responsibilities for protecting the health of persons employed in the mineral industries and for the development of useful mineral products. To assist the Bureau in the accomplishment of its objectives, this compilation has been undertaken. For the benefit of the mineral industries, and any others who may have a similar interest, this volume is made available. An earlier compilation of the Bureau of Mines on this subject was published in 1952.4 However, during the intervening years, sufficient changes have been made in State laws to warrant completely recompiling the information. This publication includes the laws of the States, the District of Columbia, Puerto Rico, and the Virgin Is¬lands through 1964. Only those portions of the workmen's compensation laws which apply to or as ' related to occupational diseases are presented, and in each case enacted additions to and deletions from the basic law have been incorporated into the text of the law, thus snak¬ing it unnecessary to search out the various amendments made each year.

Jan 1, 1967

By David Conover

Technological advancements in electronic sensors and mine-wide monitoring systems have improved remote monitoring and analysis of underground mining information. The effective use of . these systems for ground control applications, however, remains a challenge facing the mining industry. The U.S. Department of Interior, Bureau of Mines is conducting research, utilizing real-time acquisition of rock mechanics data, to provide mine operators the means to rapidly identify and manage potentially hazardous ground conditions. The Bureau has installed a remote monitoring network in a Colorado coal mine to record Pressures from instruments installed in the roof and pi1lars of gateroads and from transducers on shield-legs along the face. The field data are being monitored at the Denver Research Center, 150 mi from the mine. A computer at the Center analyzes the field data and generates graphic displays, which permit detailed examination of mine-wide ground conditions in real-time. For the first time, Bureau researchers are able to perform real-time monitoring and analysis of rock mechanics data while mining is in progress. The data collection and display capabilities of the system were effectively used to identify and evaluate face stability problems at the mine.

Jan 1, 1990

This paper presents the near-field rock damage owing to production blasting in limestone quarry in the western region of Japan. The study's purpose is to learn the mechanism of crack development due to blast vibration. In this study, blast vibration's magnitude was expressed with peak particle velocity (PPV) which was obtained based on seismographs recorded database. In attempt to pursue a research's purpose of this study, there were two considerable interests: near-field blast vibration propagation and prediction, and crack observed and prediction. Furthermore, with regards to considerable interest of the study, there were three essential aspects which were challenged, such as: monitoring and interpretation of seismic wave propagation in a rock mass near large explosive charge of production blast scale, measurement of blast rock damage in adjacent to blasthole, and determine critical value of PPV which may produce significant rock damage. In order to determine precision critical PPV, understanding correlation between rock damage with vibration level is firstly important to be done. This paper also discusses how to measure, detect and quantify near-field blast vibration and blast rock damage in adjacent to blasthole.

Dec 6, 2010

Identifying Opportunities to Reduce the Consumption of Energy Across Mineral Processing Plants

Sep 13, 2010

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By S. D. Hill, G. E. McClelland

To maximize productivity and improve minerals processing technology, the U. S. Department of the Interior, Bureau of Mines, is investigating a particle agglomeration technique as a means of increasing the percolation rate of leaching solutions through heaps of clayey or finely crushed, low- grade, gold-silver ores. Bench-scale and pilot-scale experiments conducted on different ores indicated that the percolation rate of cyanide leaching solution was enhanced markedly by mixing the ore with a binder, such as lime or portland cement, moistening the mixture, then mechanically agglomerating and aging the feed prior to heap building and leaching. In addition, the rate of silver and gold extraction markedly increased without sacrificing total recovery of values. The use of concentrated cyanide solution instead of water during the agglomeration procedure substantially decreased the leaching time required to obtain maximum recovery. Results from bench-scale and pilot-scale experiments using the particle agglomeration technique are discussed.

Jan 1, 1981

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961