Search Documents

By Sylvain Pirson

THE main value of earth magnetic measurements, outside of certain mining problems, resides in the study of deeply buried tectonic phe-nomena related to regional and local geology. Magnetic surveys are a necessary complement of gravimetric measurements, especially of pen-dulum surveys. To date, magnetometer, prospecting has been used chiefly in the study of sedimentary basins where petroleum structures are associated with the uplifted basement rocks. There are, in the literature, innumerable articles dealing with such surveys as applied to oil geology but few treat of broad geological features related to regional magnetic disturbances of the earth field. An important piece of coordina-tion work has been made by Jean Jung1 for the magnetic and gravimetric measurements made in France and their geologic significance. A similar attempt at correlation of the known geology with the anomalies of the vertical component of the earth magnetic field has been made for the United States by George B. Somers2. Taking the magnetic vector as a whole, W. P. Jenny' made a coordination of magnetism and geology for the main producing oil states of the United States. A more detailed study along the same lines is published by A. Van Weelden4 for southern Oklahoma and northern Texas; in this work magnetic and gravimetric measurements taken at stations as close as one mile apart are compiled and compared to the regional geology of the Ouachita-Amarillo uplifted area. From the literature mentioned, it is evident that reliable interpretation of magnetic anomalies can be arrived at only when the magnetic stations are numerous and cover the area in a close net of measurements, therefore the works of Somers and Jenny, based on sparsely distributed Government measurements, can be regarded only as preliminary programs indicating lines along which further work should be done, whereas the coordination made by Van Weelden is an example of the contribution to the knowledge of regional geology that can be arrived at by the use of applied geophysics.

Jan 1, 1935

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By Jonathan G. Price

Silver-copper-lead deposits In Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore in overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulflide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1984

By Tomek Ulatowski

This article discusses principal areas relevant to financing natural resource projects using as an example a hypothetical newly proposed direct reduction facility. The issues most directly affecting the project from the standpoint of financing are categorized in four groups: 1. Lenders' differing requirements with respect to projected cashflows; 2. The impact of leveraging on project viability; 3. The importance of appropriate debt structure; 4. The significance of accurate and complete capital cost estimates. The findings emphasize that the economics and the financing of a project are not only inseparable, but that they should also be viewed as directly interactive during the project planning process.

Jan 1, 1981

Beyond the industrial suburbs of Melbourne to the southeast are brown coal deposits just under the fertile soil of the Latrobe Valley. These deposits rank as one of the wonders of the world. The manner in which this resource is put to use is one of the great engineering accomplishments of our time and also a prime example of Australian elan. The brown coal, with over 60% water content, occurs in beds from 200 to 400 ft thick, under 50 ft of cover. Fifty thousand tons of coal per day move in a nearly continuous stream from mining face to boilers. The power plants supply two thirds of the State of Victoria's requirements, about 800 megawatts. Surge capacity between mine and power plant is sufficient for 12 hr steaming time! Victorian brown coals have been known since the middle of the 19th century. However, it took a strike of bituminous coal miners in 1915 to bring brown coal permanently into the picture as a fuel for power generation. In Australia, power generation is a State function. The great development of brown coals has been under the State Electricity Commission of Victoria.

Jan 10, 1964

By H. M. Wolflin

SOMEWHAT more than a year ago the writer collected some extensive notes on metal-mine fires and a paper on metal-mine fire prevention and fighting, a summary of these notes, was hastily pre-pared, with the assistance of G. Chester Brown, chief mining engineer, Industrial Accident Commission for the National Safety Council meeting. This summary, which is admittedly incomplete, is submitted in the hope that it will evoke some discussion that may result in a reduction in metal-mine fire hazard along the line. To accomplish such a reduction does not require the application of complicated scien-tific data. The use of just a little care, a small amount of thoughtfulness and a bit of common sense will work wonders. UNDERGROUND FIRE FIGHTING There may be some interest in a short list of con-clusions of a rather general nature that were reached in connection with some recent mine-fire fighting opera-tions. No effort has been made to cover the field; the items have been jotted down loosely, and very hastily, in the order in which they occurred to the writer. Originality is claimed for, only a few of them. 1. Temperature readings and analyses of mine-air samples, systematically taken, are invaluable aids to effective metal-mine fire fighting and recovery opera-tions. The analysis of the return-air samples fre-quently gives a surprisingly accurate indication of conditions existing underground. 2. Employees must be thoroughly trained in the use, of mine rescue apparatus, because a relatively slight difference in the amount of training makes a vast difference in the amount of work they can per-form under oxygen. In general, slender, wiry men make better apparatus men than those of heavy, more muscular physique, although there are frequent excep-tions to any such general statement. 3: Surprisingly high temperatures, up to 165° F. or 170° F. pan be endured for short periods by wearers of mine rescue apparatus if the air is dry, but lower temperatures, 135° to 140° F. are almost unbearable if the air is very moist.

Jan 2, 1922

By J. L. Gillson

In this past year of our Institute's life, February 1960 to February 1961, we had some major problems to face, as did our members, since businesses in which they were engaged were feeling the recession. The major problems confronting us during this past year were: 1) Financing the new Engineering Center. 2) Keeping our three almost autonomous societies working together and toward a stronger AIME. 3) Cooperation with other engineering societies the Functional Plan. 4) Licensing and registration, and the Model Law. 5) The reorganization of the Council of Section Delegates. 6) Combatting the slump in the appeal of engineering to the young students.

Jan 4, 1961

By G. Knight

In most mines the major contribution to the dust exposure of miners arises from rock hand- ling. Scooptrams are frequently used and produce 8 to 1300 mg of respirable dust for each ton of ore loaded. It is shown that sprays at drawpoints are not fully effective in wetting the rock and suggestions for improved wetting techniques are given. Techniques for improved dust control by ventilation and local filtration are described. The problem of dust from ore- passes and dumps on tramming levels are outlined.

Jan 1, 1981

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982

A. M. CANDY,* Pittsburgh, Pa.-According to the tables on page 532, the deposit obtained with Roebling cold-rolled steel, and Toucan electrodes contained considerably less carbon and manganese than the original electrodes; whereas very little carbon is lost in the case of the hot-rolled steel electrode. When using the hot-rolled steel electrodes, the metal apparently has a tendency, probably due to greater surface tension, to pass through the arc in larger particles than the other electrode materials. This affords greater protection against oxidation, and thereby prevents much loss of carbon. The larger globules tend to increase the arc fluctuations due to greater partial short-circuiting of the arc. Actual oscillographic records show that with the hot-rolled steel electrodes the current peaks were 70 per cent. above normal whereas the peaks for the other electrodes were only about 25 per cent. -above normal. Probably due to the larger globules, a greater proportion of slag in the electrode was carried into the weld. Some four or five test pieces made with the hot-rolled steel electrodes were all considerably below the tensile strength of the samples welded with the other electrodes. These facts indicate that an electrode may not be satisfactory even though of approximately the proper chemical composition. For example; the hot-rolled steel and Roebling electrodes are quite similar in chemical analysis.

Jan 4, 1919

By H. J. Maguire

(Presented by invitation at a meeting of the Spokane Local Section, Feb. 17, 1912.) THOSE familiar with mill-practice understand the work required of an average bucket-elevator, but I wish to call special attention to the wear on the buckets. I have been studying in what manner the life and service of the bucket might be improved, and I feel that an adjustable lip, attachable to each bucket without the aid of rivets, will be of material advantage. For illustration, consider the feed-elevator of a typical mill in the Cur d'Alène district. The ore is carried by water in a launder from the feed-rolls and dumped in the "boot" of the elevator, directly in front of the ascending bucket. Middlings from the return-rolls are similarly handled. Under this condition the bucket not only carries the ore, but also picks it up, and this latter requirement determines the life and service of the bucket. It might be said that it would be better practice to convey the feed to the elevator and dump it directly into the bucket, but at one mill at which this plan was tried the results were disappointing and the rubber belt was badly worn. The wear of the bucket is confined to the lip and the corners which have to pick up the material. When the lip on a corner of a 7- by 12-in. malleable cast-iron bucket is worn down about 3 in., the bucket is of no further value as a carrier and has to be replaced. The worn bucket, containing about three¬quarters by weight of the metal of the original bucket, has a scrap value of about 10 per cent. of that of a new bucket. To the cost of the bucket, however, should be added the time-cost of replacing the old bucket by a new one. This time-cost is considerable when the loss per hour, to cease operating the mill, is about $200. It is out of the question to put lips on a bucket unless the latter was originally fitted with this device. For if it is attempted to fit lips upon buckets not originally provided with

Sep 1, 1912

By Georges Millot

USUALLY the search for clays is left to chance in unexplored areas. A local working by the inhabitants or an outcrop is often the only guide. If the conditions of genesis of clays were always known, a set of general rules could be drawn up that would apply to this search. For example, a certain type of clay might be found wherever the sediment indicated a favorable environment. This paper sums up the considerable amount of knowledge that has been accumulated about the genesis of sedimentary days and offers some rules to be observed in prospecting for new clays. ANALYTICAL STUDY OF SEDIMENTARY CLAYS Clays may be found in many formations, both recent and ancient. All the intermediums exist between the deep-sea deposit and the mud deposited by a stream. In order to find out whether the nature of clay deposits depends on the environments in which they were formed, the samples used in the investigation described herein were very carefully chosen from: (1) ancient sedimentary series (a few from recent ones), (2) zones where conditions of genesis are typical. Ancient Formations Ancient formations were chosen because they are less difficult to sample than the bottom sediments of present-day lakes and seas. Moreover, a geo- logical section makes it possible to define the conditions of genesis of a deposit based on its facies, fossils, stratigraphic relations, and paleography. A present-day deposit is defined only by its aspect at the moment. Its previous history may have caused mixtures, alterations, and changes of environment, which escape detection. Typical Conditions of Genesis Samples from ancient deposits were taken from zones where typical conditions of genesis prevailed. Only clays from marine, lagoonal, and lacustrine environs are concerned in this study because the nature of the original en- vironments could be affirmed. In this way an inventory of the nature of sedimentary clays has been made for rocks formed in typical and individual environments; therefore the extent of the results that may be drawn from such a study will need discussion.

Jan 1, 1952

By AIME AIME

I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability.

Jan 1, 1967

By George S. Rice

The extremely valuable papers and discussions on coal-cluat explosions by Bache,' Eavenson, Shurick, Mannakee,* and Raymond are of unusual interest to me, since it has been my duty to carry on investigations on this and allied subjects for the Technologic Branch of the United States Geological Survey during the past year, and to make a series of coal-dust tests in the explosion-gallery at Pittsburg during a short periocl when its use could be diverted from the pressing work of testing explosives. In several of the discussions mentioned, it has been assumecl that the Technologic Branch of the Survey mas not paying attention to certain phases of the general problem, or to the specific question of temperature and humidity of mine-air in its effect upon the explosibility of coal-dust. This assumption is not correct, since from the time of the establishment of the " Mine-Accident Division," with its subdivisions of explosives, rescue-work, and mine-investigation, the mining engineer.; of the last-named section have made the subject one of chief consideration. Their general duties, including mine-sampling for governmeilt purposes, emergency-calls for rescue-work, and esplosion investigations, have prevented undivided attention, but all of them have been supplied with instruments for such determinations, and special report-forms have been in use and a great many observations made in mining-districts to which the mining engineers have gone. With the idea of obtaining a uniform system of reporting these data, and in the hope that the work may be of service to mining engineers in the field, the collecting blanks in use are shown in Forrns 1 and 2.

Jan 1, 1911

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By W. A. Bruce

THIS paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to sell-spacing problems are shown.

Jan 1, 1942

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By L. D. Frink

THOSE actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be clone in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which, permits it to be put up or taken clown in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

THE Council of the Geological Society of America has named its gold medal after R. A. F. Penrose, Jr., who recognized the need of such an award and supplied the endowment. The medal is to be awarded for achievement in pure science and may be given to a worker of any race or nation. Mr. Penrose, whose own professional work has been mainly in applied geology, had previously established a medal fund for the Society of Economic Geologists. This was awarded to T. C. Chamberlin at the meet-ing of that Society at Cornell University in 1924. The new medal is to be given on the recommendation of the G. S. A. Council, but not necessarily every year.

Jan 4, 1927

By Marvin L. Kay

In the spring of 1950, just two years after the inauguration of the domestic uranium program by the U. S. Atomic Energy Commission, the company entered the uranium mining and milling business through a newly formed subsidiary, Climax Uranium Co. This was the first venture into a new field of mining for Climax, which became the first old-time mining company, other than the vanadium producers, to become active in the embryo uranium industry. Twenty-five years earlier, Arthur Bunker, president of Climax Molybdenum, organized and operated the U. S. Vanadium Co. at Rifle, Colo. With this background, he viewed the budding industry of the Colorado Plateau with much interest. Upon its formation, the new subsidiary entered into a con- tract with the U. S. Government and the potential uranium-vanadium properties of Minerals Engineering Co. were assigned to Climax Uranium Co. Funds for the construction of a processing plant and working capital were advanced by Climax Molybdenum Co. The old sugar mill building of the Holly Sugar Co. in Grand Junction was leased to house the extractive plant. Construction of facilities, which were based upon a new process developed for the treatment of both uranium and vanadium ores, was completed and the mill was placed in operation early in 1951. Subsequent to that time several alterations were made and the capacity of the plant increased. In terms of recoveries, the plant has proved to be one of the most efficient on the Colorado Plateau

Aug 1, 1955