Search Documents

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By N. Shiarella, Coleman D. Hunter, I. B. Browning

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By I. B. Browning, N. Shiarella, Coleman D. Hunter

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By Thomas L. Garwood, F. C. Menk

IT is generally accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sues contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in I both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segregate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of coal in handling and shooting in the mine gives this small-size coal good coking characteristics-producing a strong, fingery coke structure. Deduster dust from Illinois coal has been

Jan 1, 1950

Jan 1, 1914

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

Assaying, mineralogy, and geology appear in ancient records as early as mathematics, physics, and chemistry. Agricola was the first author to unify the earth sciences, the mineral extractive industries and the mineral processing industries. His text, De Re Metallica, published in Latin in 1556, is recognized as the first technical literature. In 1702 mining instruction was started at Freiberg, Germany. The purpose of this school was to train skilled workers, a program corresponding to present-day, on-job, vocational-technical, upgrading extension training. Formal instruction in mining engineering began at Schemnitz, Hungary, in 1763, at Freiberg, Germany, in 1766, and at St. Petersburg, Russia, in 1773. It is interesting to note that these three schools initiated instruction in mining engineering before formal instruction in civil engineering began at Paris, France, in 1775. Early mining engineering, 1763-1900, was expected to cover all eventualities in the mineral industries. Optional curricula were offered early in the 20th Century but did not reach into all branches until after World War I. Specialization crystallized during World War II under three organic units: (1) Earth Sciences; (2) Mineral Engineering; (3) Mineral Technology, the three together constituting the mineral arts and sciences of the modern world (Fig. 10).

Jan 1, 1950

By Roger K. Clifford, Gary W. Hudiburgh

The amine flotation of feldspar from a magnetite concentrate produced at a domestic concentrator was investigated using zeta potential measurements, Hallimond tube flotation tests, and laboratory-scale flotation tests. The point of zero charge of six feldspars (microcline, orthoclase, albite, anorthite, anorthoclase, and oligoclase) range from pH 1.4 to 2.5. Hallimond tube flotation tests using amine flotation reagents were performed on these feldspars and on gangue material (quartz, albite, and microcline) from the magnetite concentrating plant. Laboratory-scale (623 g and 2500 g) flotation tests were performed on the magnetite concentrate to float the feldspar. The effects of three different collectors, two levels of collector concentration, three pH levels, starch, HF acid and regrind were investigated.

Jan 1, 1977

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which lie had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1878

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

The National Labor Board, on June 25, ended its activities preparatory to final, dissolution by the President. No new cases will be heard nor new applications received. Controversies, jointly submitted, that could not be concluded prior to June 30, were assigned to the joint chairmen or a section of the board for disposition. The conclusion of the board's activities marks the passing of. one of the governmental agencies created during the war to further production of war materials. The board was organized under a Presidential proclamation with former President Taft and Frank P. Walsh of Kansas City as joint Chairmen, and with five members representing labor, five employers' representatives, and two members acting for the public. Mr. Walsh resigned soon after the signing of the armistice and was succeeded by Basil M. Manly of Washington. During the year that ended May 31, the hoard received 1245 cases, made awards in 462 cases, dismissed 391 for various cases, referred 315 to specified agencies, and suspended one case. Fifty-three cases remained on the docket because the hoard could not agree, and 23 cases were pending.

Jan 8, 1919

By Albert G. Anderson

I'm sure many of you have wondered what the term "Cross Flow Filtration" means. I shall explain it so that you more clearly understand it, and I hope you will be able to make it a useful tool for you in the future. In the simplest form of cross flow filtration contaminated fluid. or feed stream, is fed at a high velocity down the center of a porous tube, clear fluid weeps through the porous wall of the tube while the suspended solids concentrate in and are swept away by the feed stream. (See figure A). The high velocity flow of the feed stream tends to keep the inside of the tube free from a build up of contamination. By utilizing this cross flow approach to filtration, we have been able to concentrate such things as paint pigments, titanium dioxide, iron oxide, precipitated metals such as uranium yellowcake or silver, cadmium, some metal hydroxides, as well as gelatinous particles such as yeast cells. You will recognize that cross flow filtration lends itself to a recirculation loop system due to the necessity of maintaining a high velocity on the inside of the tube. This means that we generally have a storage tank from which we are recirculating, and the solids will concentrate in the storage tank. (See figure B). The storage tank design becomes an integral part of the total system and is very important to the total function of the system. The cross flow filter system requires only low pressure, and will work with centrifugal pumps, diaphram pumps or in some cases no pump at all. As an example, if we wanted to filter a 10 GPM (37.8 liters/min.) stream that contained 1% of submicronic particulate, we would flow the 10 GPM (37.8 liters/min.) into the storage tank and recirculate through the filter at a flow of anywhere from 30 GPM to 100 GPM (113.6 to 378.5 liters/min.) depending upon the filterability of the particles from the liquid. As the contaminated fluid recirculates, the solids will build up in the storage tank and loop until they reach a level, which is dependent upon the design of the tank. Then the settling rate in the tank becomes equal to the amount of the solids being fed to the tank, and as a result you reach an equilibrium in the amount of solids being presented to the inside of the porous tubing. We have in effect created a dynamic settling tank or thickener. A flow of 10 GPM (37.8 liters/min.) of clear filtrate comes off for either recycle or disposal with periodic removal of thick mud from the bottom of the tank. The thick mud can be either processed through a centrifuge, a rotary drum filter. a flat bed pressure type filter, or other means. Often the small volume of filtrate from the mud de-watering stream can be recycled back into the recirculation tank so that any fines in the feedback are again concentrated, thus closing the loop on the continuous process 100% removal system. Cross flow filtration will not do efficient molecular separation. We work primarily with discrete solids but we do separate them totally from the liquid carrier fluid. I know some of you will raise your eyebrows when I say that we remove 100% of the particulate, but in measurement tests, we have measured the filtrate cleanliness with instruments that record as low as .05 ppm and the instruments read zero, so that it is less than .05 ppm.

Jan 1, 1980

ALABAMA Anniston.-Bretz, J A Carnngton, F G Gerber, A B Ashland -Barton J Sturdevant, J C Bessemer -Abbott, C E Ball, T L Ferguson, V Salmon, H S Schaber, C F Thompson, N E Whatley, W J Birmingham.-Adams, J H -Aldrich, T H Aldrich, T H , Jr ALASKA Anchorage -Dyer, B W. Parker, H C Smith, S S Chichagof.-Baumann, H N , Jr Copper River.-Douglass, W C Cordova.-Hazelet, G C Fairbanks -Davis, J A Hyder -Pitt, D L Juneau -Jackson, G. T Murphy, R E R..11 ti At i

Jan 1, 1923

By R. C. Patterson

IN view of the circumstance that very few important changes have been made within the last 15 or 20 years in the equipment of rod and wire mills, the description of a new process introduced by Grenville Mellen, of Llewellyn Park, N. J., to take the place of the present laborious system of producing rods of lead, zinc, brass, copper, aluminum, etc., may be interesting to members of the Institute. This new process consists in the production of cast rods at one operation in a small continuous casting machine. The hot liquid metal is transferred from the melting crucibles directly into an endless chain of mold blocks in the machine, where solidification takes place, and the rod comes out continuously in a solid form at one end as long as the molten metal is supplied. The operation of these mold blocks so as to produce a solid rod of uniform structure constitutes an important part of Mr. Mellen's invention. The machine (Figs. 1 and 2), 12 ft. in height over all, 2 by 3 ft. in horizontal- cross-sectional area, and 6,000 11). in weight, has a framework of cast iron, holding in position two endless chains of mold blocks, which are made in sections and join in center alignment. The mold orifice is made up of these mold sections, into which the liquid metal flows. The molding chains are composed of steel blocks, grooved on one face to form the molding cavity, and linked together with flexible joints. Each block is carried on four rollers which guide the chain around the end sprockets and carry it in its course through the machine. The accuracy of alignment requisite to the production of a perfect rod in the mold groove formed by these sections is secured by careful machine work, and by building the four ways, down which the alignment takes place, so that two of the sides are fixed permanently, while the opposite sides are held to their position by spring pressure. The guides carrying the molds, while in casting position, are water-cooled square tubes.

Jan 5, 1915

By Thomas L. Garwood, F. C. Menk

IT is generally, accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segr6gate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of .coal in handling and shooting in the mine gives this small-size coal good

Jan 1, 1943

Steps were taken for a permanent organization of the scientific and technical employees of the Government at their mass meeting on May 8. This was the result of an informal meeting on Apr. 23 of thirty representative Government scientists and technical men who organized the preliminary committee and called the mass meeting. This subject has been widely discussed during the last year and was brought acutely to the fore by the work of the Joint Congressional Reclassification Commission, because that Commission has stated that it wished to deal with employees only through organizations. Rodney H. True of the Department of Agriculture was Acting Chairman. He pointed out that the principal advantages that were expected to be derived from such an organization were: (1) Improvement of conditions and facilities for more effective scientific and technical work; (2) adequate presentation of the needs. and results of such work to the public and to legislative and administrative officers; (3) -greater freedom in both official and non-official activities; (4) just and reasonable salaries based on service performed and the economic and social conditions which prevail; (5) greater public recognition of the aims and purposes of research; (6) advancement of science and technology as an essential element of national life. Three plans of organization were offered to the meeting, which covered the fundamental principles which could be utilized by these Government employees. The first plan would have permitted the new organization to work only through existing scientific organizations. This is the plan that scientific and technical Government employees in England have adopted and an outline of the English plan was read to the meeting.

Jan 6, 1919

Jan 1, 1939

Jan 1, 1939

Jan 1, 1913