Search Documents

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By K. M. Busen, J. Lindmayer

A heterojunction model is suggested for descrihzng the electronic conditions at oxide -semiconductor interfaces. Detailed study of the silicon oxide-silicon interface shows that the heterojunction model explains many experimental facts; however, it is necessary to assume that a transition layer exists at the interface. It will he demonstrated that ionic contrbution way also he present. Extended low-temperature heating stabilizes the oxide to a charge carrier density in the order of 10' cln-: determined by the heterojuncton model. OXIDIZED semiconductor surfaces are widely used, since they offer technological advantages and "passivate" the surfaces of semiconductor devices. However, it has been recognized that there are always n-type inversion layers formed in the silicon oxide-silicon system, which must be regarded as a definite disadvantage. An added complication is the "instability" of these inversion layers;' the inversion layer appears to vary with the processing and they change at temperatures as low as 100" to 200°C This paper will point out that the inversion layer is a result of the dissimilarity of the contacting materials and therefore must always be present. The dissimilarity is the essence of the heterojunction or electronic model and involves directly the structure of the materials involved. In addition, one finds the contribution from ions; this disturbance, however. can be eliminated for the case of silicon oxide-silicon interface. The strength of the inversion layer or channel will be expressed in terms of the density of elementary charges per square centimeter, N*, maintaining the channel. The next section contains the formulation of the heterojunction model by assuming a contact between two homogeneous materials. This calculation should not imply that silicon oxide is homogeneous; it serves only to point out the general properties of the electronic model. Following the electronic model, the practical case of the silicon oxide-silicon interface will be discussed. I) THE HETEROJUNCTION MODEL Contacting an oxide with a semiconductor, a work-function difference must be accommodated. Fig. 1 represents the oxide and the semiconductor before and after contact. When the contact has been made, one finds that qVi + qV, = A@; i.e., the work-function difference is distributed between the oxide and the semiconductor. Normally, the work-function difference appears on the wide-bandgap material, but in the present case the oxide is thin and far from being a single crystal. Accordingly, a significant fraction of the work-function difference must appear on the semiconductor. The work function of silicon2 is about 4.8 ev, but we shall not assign any particular work function for the oxide as it may vary. However, oxides usually have lower work functions and therefore the potentials must build up in the manner shown in Fig. 1. Such an argument predicts that the inversion layer must be n type, as opposed to the clean surface which is p type. Another important factor to be considered is that the oxide is disorderly and therefore contains many trapping levels. As a result, the charges in the oxide arise primarily from the change in trap occupation, while on the semiconductor side the space charge is composed of mobile free electrons. The consequence of this fact is that a change to another thermal equilibrium will require some time, dictated by the traps in the oxide. The conditions can easily be calculated on the semiconductor side. Assuming an intrinsic semiconductor, Poisson's equation is

Jan 1, 1965

By J. H. Wernick, J. E. Kunzler

HIGHLY pure metals are needed for low-temperature electron transport studies in progress. Recent improvements in purification techniques, such as zone refining, have made it possible to obtain metals with improved purity. For some metals, the improvement has been to the extent that ordinary analytical techniques are inadequate and special methods are needed.1 For other metals purification is more difficult, so that simple but rapid analytical methods are desirable as an aid in evaluating the effectiveness of purification procedures. Furthermore, it is desirable to be able to determine the impurity level of the sample or ingot with the minimum of physical disturbance of the material. In order to aid in the preparation of purer metals, techniques involving the measurement of electrical resistance at liquid-helium temperatures have been devised for studying impurity distributions in zone-refined ingots and other bulk samples without destroying the ingot or its geometry. The method yields information on the variations in purity along the length of the ingot or sample and provides a measure of the overall purity of the material. Compared with ordinary analytical methods, the resistivity method is rapid, sensitive, and does not require significant physical disturbance of samples with reasonable shapes. It has the disadvantage that resistance measurements are not specific, i.e., they do not identify the impurity. However, this disadvantage is offset by the advantage of being able to establish a measure of the overall purity so far as electrically active" impurities are concerned. METHOD AND ITS BASIS The method is based on the well-known fact that the resistivity, at Liquid helium temperatures, of a reasonably pure metal containing no regions with additional phases decreases with increasing chemical purity or a decrease in the number of physical defects. It is convenient to separate the total resistivity into three parts: where is the resistivity due to the scattering of the conduction electrons by the lattice vibrations or phonons, p is the contribution due to physical defects, and originates from the effect of chemical impurities in the metal. Insofar as Matthiessen's rule is obeyed,2 pphys and pchem are independent of temperature. Except possiblyin the very purest metals, ptherm is negligible at liquid helium temperatures and For zone-refined metals, which normally are well annealed and consist of large grains, at the chemical purity levels thus far attained the available data indicate that pphys is negligibly small or at least constant throughout the ingot. Assuming that the effect of physical defects is negligible for isotropic metals, This assumption appears consistent with most of

Jan 1, 1959

By Kendall E. Born

PRoduction of crude oil in Tennessee during 1938 was slightly more than 41,000 bbl., an increase of about 5000 bbl. over 1937. The production by counties and by fields is shown in Table 1. The increased production has resulted from continued activity in the Upper Cumberland district, especially in Clay County. The "Mississippi lime" production in Scott and Morgan Counties continued to show a further decline with a 1938 production of 12,379 bbl. as against 14,644 bbl. during 1937. Small scattered production from some half dozen wells in Clay, Pickett, and Fentress Counties, on which there are no accurate figures, is estimated at 500 bbl. during the year. The only natural gas marketed off the lease in Tennessee during 1938 was in Morgan County, where a small amount was furnished for the town of Sunbright and immediate vicinity. The gas occurs with the oil in the Boone Camp field and small amounts were put on the line from the near-by Coon Hollow and Seabolt pools. Developments There were 88 wells spudded in during 1938, of which 10 were drilling or only temporarily shut down on Dec. 31, 1938. Eighty wells were completed during the year; 16 produced oil and 3 were gas wells of undetermined quantity. The total footage drilled on 1938 completions was 63,385 ft. Flush production during the year totaled 850 bbl. per day. The more important wildcats are listed in Table 2; the distribution of oil and gas tests drilled during the year, according to physiographic divisions, is given in Table 3. Cumberland Plateau There were no completions in the producing pools in Scott and Morgan Counties. The decline in production in these areas has been steady for the past several years. In an effort to revive production, present plans include a repressuring program in the Boone Camp field in Morgan County early in 1939. There was one completion in Morgan

Jan 1, 1939

By Kendall E. Born

PRoduction of crude oil in Tennessee during 1938 was slightly more than 41,000 bbl., an increase of about 5000 bbl. over 1937. The production by counties and by fields is shown in Table 1. The increased production has resulted from continued activity in the Upper Cumberland district, especially in Clay County. The "Mississippi lime" production in Scott and Morgan Counties continued to show a further decline with a 1938 production of 12,379 bbl. as against 14,644 bbl. during 1937. Small scattered production from some half dozen wells in Clay, Pickett, and Fentress Counties, on which there are no accurate figures, is estimated at 500 bbl. during the year. The only natural gas marketed off the lease in Tennessee during 1938 was in Morgan County, where a small amount was furnished for the town of Sunbright and immediate vicinity. The gas occurs with the oil in the Boone Camp field and small amounts were put on the line from the near-by Coon Hollow and Seabolt pools. Developments There were 88 wells spudded in during 1938, of which 10 were drilling or only temporarily shut down on Dec. 31, 1938. Eighty wells were completed during the year; 16 produced oil and 3 were gas wells of undetermined quantity. The total footage drilled on 1938 completions was 63,385 ft. Flush production during the year totaled 850 bbl. per day. The more important wildcats are listed in Table 2; the distribution of oil and gas tests drilled during the year, according to physiographic divisions, is given in Table 3. Cumberland Plateau There were no completions in the producing pools in Scott and Morgan Counties. The decline in production in these areas has been steady for the past several years. In an effort to revive production, present plans include a repressuring program in the Boone Camp field in Morgan County early in 1939. There was one completion in Morgan

Jan 1, 1939

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By H. D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. Rut discrepancies arise. Every maker and every User of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By Henry D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

By Ralph Arnold

Since 1915, when Elk Basin field was brought in, eight oil fields have been developed in Montana and the production has arisen from 50,000 bbl. in 1916 to 8,000,000 bbl. in 1926. The production for 1927 was 5,121,600 bbl. and the total up to the end of 1927 was 27,138,239 barrels. The eight fields, with their year of discovery are: Elk Basin, Carbon County (1915); Devil's Basin, Petroleum County (1919); Cat Creek, Petroleum County (1920); Soap Creek, Big Horn County (1921); Kevin-Sunburst, Toole County (1922); Lake Basin, Stillwater County (1924); Pondera, Pondera and Teton counties (1927); and Bannatyne, Pondera and Teton counties (1927). About 170 wildcat wells have been drilled in the state of which 8 were successful and 162 gas wells or dry. Hence, only one out of 21, or 5 per cent. of the wildcats have been successful. The average depth of the wells has been 1600 ft. and the average cost $32,000 apiece. • Up to Jan. 1, 1927, a total of 1376 wells have been drilled in the producing oil and gas fields of the state, of which 904, or 66 per cent., were successful oil wells; 82, or 6 per cent. were gas; and 390, or 28 per cent, were dry. The percentage of dry wells is excessive as compared to the wells in other states, due to the uncertainties of limestone reservoir rocks. The total production of oil to Jan. 1, 1927, has been 22,016,639 bbl. and of gas 7,265,330,000 cu. ft. The average price at the well for the oil has been $1.47 per bbl. and for gas about 4 c. per 1000 cu. ft. The value at the point of consumption has been about 23 c. per 1000 cu. ft. The total revenue derived from crude oil has been $32,277,119, and from gas 8350,613, or a total income to the producer of $32,727,832. Each well drilled in the state has already (to Jan. 1, 1927) averaged a return of over $21,000. The total number of domestic (Montana) oil and gas companies organized, since the first in 1885, has been 844, of which 702 are still alive and 142 dead. Oil and gas companies registered for operation within the state to Jan. 1, 1927, but with outside charters, are 143, of which 66 are alive and 77 are dead. Outside the few distributing companies, which are included in these figures, the grand total of 997 companies which have

Jan 1, 1928

H. M. HOWE, Bedford Hills, N. Y.-One wonders, whether it might not be well to check, by a rather simple and direct way, the inferences that would be drawn from this investigation. Suppose we quench, in these various liquids cylinders of steel, selecting material that is not likely to split in hardening, and then examine their cross-sections micro-scopically. If the cylinder is of any size, you will find a series of concentric bands, a very hard band, a softer band, and a hard band-but it seems that here would be a way of checking the inferences from the cooling curves by comparing these waves of hardness obtained in similar speci-mens quenched in different liquids. One would think that there would be great promise in that way. One's first thought is to quench similar pieces of steel, similarly heated, in different liquids and determine their hardness. I suppose many of us have tried that. We then meet the-difficulty that it is not the most rapid cooling that gives the greatest hardness. There is an intermediate rate of cooling that gives maximum hardness so that you can not by any simple method as that check this cooling method. But it seems possible

Jan 12, 1919

By P. Somasundaran

Flotation of minerals has usually been discussed in terms of solid-liquid interfacial phenomena. This paper discusses the relative importance of phenomena such as collector adsorption at other interfaces formed between the bubble, liquid and solid. Adsorption of collector ions of various chain lengths at liquid-gas and solid-gas interfaces has been obtained. The data have been analyzed under conditions corresponding to those of flotation to show the significant role of collector adsorbed on the bubble surface in determining the bubble-mineral attachment required for flotation, and consequently to suggest consideration of this role in the development of better flotation conditions. Vacuum flotation of quartz with alkyl ammonium acetate reported in the foregoing paper1 showed that the collector chain length has an effect on flotation even at concentrations below those necessary for hemi-micelle association of the hydrocarbon chains at a solid-liquid interface. This chain length effect might be explained by the following arguments: Hydrocarbon chains find it energetically favorable to be in a medium of low dielectric constant. Considering the possibility of an iceberg structure at the solid-liquid interface, such a structure would produce a region of lower dielectric constant at the solid-liquid interface than in the liquid phase, because the dielectric constant of ice is 2 to 3,2 while that of water is 80. Depending on chain length, this difference will certainly cause even individual ions to adsorb in higher quantities at the solid-liquid interface. Another mechanism to consider is the possible formation of dimers, trimers, etc and chain length would influence this formation. But, above all, the chain length effect on flotation at concentrations of low adsorption at the solid-liquid interface could be due to the significant but often-neglected role of the collector adsorption at the bub- ble surface. Collector ions or molecules are adsorbed both at the solid-liquid interface and the liquid-gas interface. Below the concentration for hemi-micelle association at the Stern plane adjacent to the surface, the bulk of the collector ions adsorbed at the solid-liquid interface are in the diffuse part of the double layer. If such systems, where there is a gas bubble coming in contact with the solid surface, are to achieve some degree of electroneutrality, those collector ions would have to migrate from the diffuse part of the double layer to the region directly adjacent to the surface during the induction period when the bubble is making contact with the solid. The time necessary for this migration would contribute to the induction period required for creation of the solid-gas interface. It seems reasonable that the induction period could be reduced sufficiently for flotation to occur if these collector ions were carried to the surface by the bubble. In an attempt to ascertain whether or not the bubble could possibly have sufficient collector ions at its surface to meet the requirement mentioned above, the adsorption density of the collector ions at the liquid-air interface was determined. For this purpose, the surface tension of alkyl ammonium acetate solutions was determined as a function of concentration. Adsorption densities of the collector at the liquid-gas interface were calculated using the Gibbs adsorption equation: where y is the interfacial tension and ri and pi are the adsorption density and the chemical potential, respectively, of the chemical species, i. Using the convention that the adsorption density of water at the interface is zero, the following relationship is obtained for the liquid-gas interface where lg refers to liquid-gas interface and RA+ refers to the alkyl ammonium ions. For dilute solutions, rf^-wri^&rfwW [3] where C is the concentration of the collector ions in solution. l?:: can now be evaluated using Eq. 3 and surface tension measurements.

Jan 1, 1969

By J. J. Taber

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By S. S. Cole, D. L. Armant

The smelting of titaniferous ores for the past hundred years has not been successful because of thickening of the slags in the furnaces. The interest in the utilization of these iron bearing materials has been due to the extensive deposits which have been found in various parts of the world.1 The literature contains references2 to the use of titaniferous ores in blast furnaces. None of these attempts has met with success due to the lack of sufficient information as to the cause of failures and to economic considerations. Evaluation of the published information, as to the probable cause of failure in various attempts, has indicated that the presence of lower valence titanium oxide and formation of titanium carbide contributed to the failure. It was apparent that severe reducing conditions which are present in a blast furnace had been one of the factors for such failures. The previous smelting operations had as a primary objective the recovery of iron from these ores. Under these conditions the highest recovery of iron could only occur with severe reducing conditions. Application of Melting Point Data The application of the melting point data, from the system CaO-MgO-Al2O3-TiO2 reported in another paper,3 to the smelting of titaniferous ores required an extrapolation of these melting points due to the presence of other impurities from the ores. Likewise, a study of the effect of varying FeO and reduced titanium content of the slag was necessary before the data could be fully applied. The melting point data under oxidizing conditions had clearly indicated that a fluid slag with a melting point in the temperature range of 1370°C could be obtained. The smelting of a titaniferous ore had as a primary objective the production of a high titanium slag which was fluid and substantially free of iron and low in trivalent titanium. Since production of a high titanium slag was of primary importance, rather than the recovery of iron from these ores, the smelting concept could be altered to a marked degree. The ferrous oxide could be maintained at higher levels than is the normal practice in iron ores slags without being detrimental to the slags, although a loss in iron recovery resulted. During the reduction of the molten mixtures of ferrous iron and titanium, carbon acts as the reductant for changing the valence of the titanium and iron. The reaction can go further than in the case of the reduction which occurs in iron-titanium solutions. The formation of metallic iron removes iron from the system, so that the titanium oxide can be reduced to trivalent and divalent titanium oxides and also form titanium carbide which removes the titanium from the slags as a soluble constituent. The problem, therefore, resolves itself into maintaining the proper amount of ferrous iron in the slag thereby avoiding the formation of appreciable amounts of trivalent titanium and no divalent titanium oxide or titanium carbide. The latter two have been found in the viscous

Jan 1, 1950

By Henry Hibbard

AT THE beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as .it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By Cyril Smith

SEVERAL investigators, mainly concerned with the mechanical proper-ties of the alloys, have studied the so-called aluminum bronzes after various quenching and reheating treatments. Of these works, perhaps the most complete is that of Bouldoires,1 who studied changes of length, electrical conductivity, thermoelectric force, hardness and micro-structure oh tempering quenched alloys containing 5 to 20 per cent of aluminum, although the work of Carpenter and Edwards,2 Curry,3 Greenwood,4 Braesco,5 Matsuda;6,7 Grard8 and others has added much to our knowledge of the changes occurring during tempering. The so-called acicular ß decomposes on tempering at temperatures between 350° C. and the eutectoid, giving rise to a Widmanstätten structure of a needles in a matrix of d or fine a + d, associated with an increase in hardness and almost complete loss of ductility. Matsuda, studied the' eutectoid transformation by means of dilatation and electrical "conductivity measurements during cooling at different rates. He found that on cooling at the rate of 10° C. per minute there was a decrease in electrical resistance and in length instead of the usual increase which occurred with slow rates of cooling. On tempering the rapidly cooled samples, the increase commenced at about 400° C. and at 520° C. the resistance and length had reached the equilibrium values. These peculiarities he accounted for as being due to a transitional phase ß' being formed, ß having an electrical resistance and volume less than either ß or a + d.

Jan 1, 1933