Search Documents

By F. C. Blake

THE test of the English cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in me of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set, into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

By John S. Rinehart, Norman Ahlquist

The model which Birkimer has developed to explain the increase in fracture strength of brittle, rock-like materials with increasing rate of loading may have some applicability. It should be noted that since his analysis presupposes elastic behavior he could equally well express his result as an increase of stress to fracture with increasing strain rate, a fact which is well known. Certainly his experimental results do not contradict his strain rate to the one third power law. On the other hand, we do feel that the data are insufficient and inadequate to establish the relation- ship definitely. 'In metals, the whole fracture picture is greatly complicated by concomitant plastic flow and, in rocks, by the presence of macroscopic flaws and inhomogeneties. Both lead to uncertainties as to the state of stress during the fracture process. He quotes in support of his theory Rinehartfs results on rock in which the latter found that under impulsive loading by explosives, rocks appear to be many times stronger than under static loading. We suspect that the observed increase has little specific relevance to the theory which Birkimer puts forward. Rinehart's measurements were made by spalling rocks using a sawtooth shaped stress wave of known intensity and duration. The rise time of such a pulse is essentially zero, certainly less than 0.1 microseconds, so that it is not possible to apply Birkimerfs theory quantitatively. We favor attributing the increase in fracture strength to two factors. First, the action takes place very quickly in an exceedingly thin region so that statistically the probability is small of encountering one or more of the large flaws that contribute so significantly to the reduction of strength of most rocks under tension. It is also conceivable that the compressive wave that has just passed by the region of fracture has strengthened the rock by collapsing some of the larger flaws. Second, the state of stress obtaining at the time of fracture is not all that existing when the

Jan 1, 1971

By Gilbert L. Eggert

The effects of reactor irradiation on age hardening in a Cu-2 wt pct Be alloy have been investigated in two neutron-energy ranges. During some of the irradiations, specimens were exposed to high-energy fission neutrons which passed through a boron-10 shield; during other bombardments, the boron-10 was omitted and specimens were irradiated in a reactor thermal column, or the fuel configuration was modified to increase the thermal-neutron flux at a location in the core. Differences in length, X-ray diffraction angle, and hardness indicated that low-energy neutron irradiation made a small contribution to changes in the measured properties. The influence of defects generated by knock-om with less than the Brinkman critical energy or by prompt (n,y) recoil is suggested as the cause of this effect. EXPERIMENTS designed to test the effects of reactor irradiation on the properties of age-hardening alloys have to the present time employed fluxes un-differentiated according to neutron energy. Billing-ton and Siegell in 1950 were the first to perform such an experiment and to compare the results with those obtained by thermal aging. These authors concluded that precipitation in a Cu-2 wt pct Be alloy was not enhanced by the radiation. However, 4 years later, Murray and Taylor,2 working with specimens of the same Cu-2 wt pct Be alloy, reported that an increase in density, hardness, and resistivity which followed reactor irradiation resembled changes associated with thermal aging at about 100°C. (It should be noted that these authors reported that higher aging temperatures caused a decrease in resistivity.) cupp3 reported hardness results similar to those of Murray and Taylor. Koppenaal4 showed that irradiation-enhanced precipitation and irradiation defect hardening were not simply additive but that they acted separately in an irradiated alloy. Kernohan et a1.,5 working with Ni-Be, offered evidence that beryllium was removed from solid solution by reactor irradiation and suggested that the mechanism was one of increased diffusion through the use of vacancies in the structure. piercy6 also found that more precipitate particles were formed by fission-neutron irradiation of a Cu-Co alloy which contained a small amount of particles before irradiation. He proposed that the additional particles were caused by an appreciable amount of diffusion during the final cooling of displacement spikes. The retrogression of extant precipitate particles found by Murray and Taylor2 and Boltax7 as well as piercy6 indicated that nuclei were dissolved within a high-energy spike region and, upon resolidification of the perturbed volume, new nuclei precipitate and grow by enhanced diffusion. Bleiberg et al.' and Konobeevski et al.' explained phase changes obtained by irradiating fissionable alloys in terms of retrogression and re-precipitation in regions of high-energy spikes. Parsons and Balluffi10 used electron microscopy to verify that crystallization did indeed occur in displacement spikes which were formed in amorphous germanium by fast-neutron irradiation. The concept that low-energy neutron irradiation might cause structure-sensitive property changes in semiconductors by atomic recoil associated with the (n, y) reaction was first proposed by Schweinler" and walker." This thesis was tested by Cleland and crawford" and found to be valid. Coltman et al.14 exposed a variety of pure metals to thermal-neutron irradiation at cryogenic temperatures and attributed the resulting resistivity changes to the action of defects created by (n, y) recoil. The present work was undertaken to extend the concepts of Schweinler," walker," and Coltman et al.I4 to the case of an age-hardening alloy and to determine whether or not the action of defects produced by thermal-neutron irradiation would en-hance age hardening. EXPERIMENTAL PROCEDURE Omeea West Reactor Irradiations.* Thermal-

Jan 1, 1965

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.' Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By F. H. Callaway, W. O. Keller

The various theories as to the well spacing-recovery relationship are reviewed in considerable detail and these theories analyzed in terms of their consistency with modern reservoir engineering concepts. It is concluded that the well spacing problem must be analyzed in terms of recovery efficiency and that a positive answer to the relation between well density and recovery efficiency is not available from direct comparisons of the production histories of wells and fields. The results of an engineering analysis designed to permit approximate calculation of recovery efficiencies as a function of well spacing in a depletion type reservoir from basic reservoir data is presented. Results of this type analysis indicate that the effect of well spacing on recovery efficiency in depletion type reservoirs can be expected to be very small. Limitations of this approach are pointed out, particularly with respect to its application in lenticular reservoirs. Testing techniques are outlined which should indicate whether or not a reservoir is continuous between wells and whether or not satisfactory drainage is being obtained with present spacings. A mass of data of this type indicates continuity to exist in most fields. INTRODUCTION The purpose of this paper is to review critically the engineering aspects of the well spacing problem, both from the standpoint of certain concepts and from the standpoint of reservoir mechanics. The well spacing problem is primarily an economic problem in which the optimum well density for a particular field is that density which will yield the greatest oil recovery consistent with justifiable development costs. The well spacing answer in terms of economic conditions, however, is extremely sensitive to the variation in recovery efficiency with well density. The variation in recovery efficiency with 'References given at end of paper. Manuscript received at the office of the Petroleum Branch October 2, 1949. Paper presented at the Petroleum Branch Meeting in San Antonio. Texas, October 5-7. 1949. well density is properly an engineering problem. Different opinions as to the correct answer to this engineering problem is the basis for most of the wide difference in opinion among various members of the industry as to optimum well spacing. This paper will be confined to the engineering problem of the relation between well density and ultimate oil recovery; economic considerations necessary for the evaluation of optimum well density for any particular field will not be discussed. The paper can be logically divided into two parts. The first part deals with a critical examination of the background and logic of the Cutler Rule and of similar studies by other authors and of related well spacing concepts. It is indicated that the variations in recoveries with well density* observed by Cutler and. others can be logically attributed to regional migration. Theoretical justification of the Cutler type relation wherein observed variations in recovery with well density in the same field is attributed to variations in recovery effiiency, in terms of energy relations, is refuted. The second part consists of a review of concepts of reservoir mechanics with regard to the well density-recovery relation. It is indicated that little variation of recovery efficiency with well density can be expected in a depletion type reservoir, unless lenticular conditions prevent communication between wells. The significance of field test data with regard to the existence or non-existence of lenticular conditions is pointed out. THE CUTLER RULE The first published article concerning the engineering aspects of the well spacing problem to receive wide attention was the work of W. W. Cutler' of the U. S. Bureau of Mines, published in 1924. In a study of decline curves from a large *The expression "well density" as utilized herein refers to the number of acres attributed to each well in a uniform well pattern, and is expressed in acres per well. The term "well spacing" Is utilized to denote the average distance between adjacent wells in a uniform well pattern. †Although the Cutler rule is treated critically in this discussion the authors intend no personal criticism of W. W. Cutler or of his hark The currently accepted concepts of reservoir mechanics were no": existent at the time of Cutler's work, as were even the moat basic tools (such as the bottom hole pressure bomb) for observing reservoir behavior.

Jan 1, 1950

By John D. Erickson, Thomas R. Carlson, Milton T. Pana, Daniel T. O’Brian

Computer use in mine planning has evolved from theory to practical application at the Bingham mine of Kennecott Copper Corp.’s Utah Copper Division. Traditional mine planning methods have been combined with computer technology to produce a more realistic calculation of ore reserves and mining plans. The techniques used are not revolutionary but are an expansion of previous mine planning methods using the calculating power of the computer. These methods can readily be adapted for planning use by practical mining men.

Jan 5, 1966

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.1 It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to be drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the ?' phase," CuA12." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in ?' lying parallel to this plane are roughly similar to those opposite it in the matrix.' The formation of ?', however, is preceded by the formation of a transition lattice ?', which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly perfect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.4-8 Particles of ?' may be recognized microscopically and form a well-defined Widmanstätten figure.* The ?' lattice is recognized by the occurrence of diffraction lines on powder photograms or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6.7,1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a few hundred atoms in diameter, probably of the composition of "CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact merely ?' in a high state of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By P. G. Mason

The upswing in the price of gold in 1979 prompted renewed interest in the Mercur gold property by Getty Oil Company, owner and operator, and Gold Standard Inc. of Salt Lake City, Utah, currently retaining a 15% net profits interest. Extensive geological exploration work resumed to delineate the ore reserves, and metallurgical test work was initiated under the direction of A.H. Ross & Associates. This led to the development of an aqueous pressure oxidation process suitable for treatment of the refractory ores. Subsequent geostatistical studies revealed that the distribution of high refractory ore was less than previously estimated, and thus a higher return on investment could be realized if a direct carbon-in-leach process were used despite a sacrifice in overall recovery. This paper reviews the geological and metallurgical studies that led to this final process selection.

Jan 1, 1984

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Herbert H. Uhlig

Although the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldla summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.I5 per cent carbon. He noted: From these comparisons it wil! be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable.lb His data showed that alloys containing 4 to 10 per cent manganese water-quenched from Iooo°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 87o°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loring2 reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 54o°C. (Iooo°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to &apos; 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.I5 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <o.ooI per cent P). In this paper it is shown that of the low-carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from IOOO°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

By Bruce W. Gonser

TIN is not yet classed as a rare metal, but it has taken a long stride in that direction in the last ten months. It is now in Group 1 of the War Production Board&apos;s critical list, along with such company as magnesium aluminum, and nickel. This is in sharp contrast with the position a year ago when the supply well exceeded demand, and tin was used when feasible in place of really scarce metals. The geographical sources of tin production in recent years are shown in Table 1. Preponderance of former production in southeastern Asia, particularly Malaya and the Netherlands Indies (but all now controlled by the Japanese). is entirely too marked to be funny. Of the 1940 known world production of 237,000 long tons nearly all was controlled by the United States, Great Britain, and their friends. Now their supply is from countries that produced only 28 per cent of that amount. This excludes China and Australia, which because of shipping difficulties and local consumption, cannot be expected to export much tin. In spite of some expected increase in production, therefore, the supply is, and will continue to stay for at least several years, way below that desired for even normal uses. Although deliveries to consumers in the United States alone

Jan 1, 1942

Roger A. Markle was sworn in as director of the US Bureau of Mines on September 27, 1978, ending a 20-month period during which the Bureau was without a leader. Some Bureau observers wondered out loud if this delay was a signal that Interior was slowly pulling the rug out from under the agency. When Markle was finally tapped for the director&apos;s position-coal industry executive to lead an agency that had been stripped of its fossil fuel R&D functions as well as its safety and health enforcement role--the speculation was fast and furious: One camp had it that Markle was brought in to phase out the Bureau; others said that Markle&apos;s directive was to revitalize the organization by charting a new Bureau course. In March, with the proposed Department of Natural Resources making headlines, ME went to Washington to interview Markle about his first six months as director and the goals he has set for the Bureau&apos;s future.

Jan 4, 1979

By O. W. Ellis

THE question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,1 Iwasé,2 Lobley and Jepson3 stand preeminent. SOLUBILITY OF . GASES IN. COPPER Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate-possibly 30° to 60° C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts&apos; most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1928

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By G. H. Ashley

THE Pittsburgh coal bed stands today: as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? To the present it has contributed more than 2,530,000,000 tons of high-grade coal from Pennsylvania alone, worth nearly $4,000,000,000. Since 1910 it has added more than $2,500,000,000 to the value of Pennsylvania&apos;s mineral output. There is estimated to be about three times as much coal still in this bed as has been mined. To realize the full value of this wonderful bed it must be remembered that the figures given are for one State only. To them should be added the figures for the same bed from West Virginia, Ohio and Maryland. Furthermore, as known by man, this great deposit is only a fraction of its original whole. Outliers in Somerset County, Pa., indicate that its original extent in Pennsylvania in an east and west direction was more than two times its present extent. Add to that the northward extension as indicated by outliers in northern Allegheny, Armstrong and Indiana counties,, and it seems safe to say that its original extent was not less than three times the area at present underlain by it. And as the subjacent beds of the Allegheny group are found still further eastward and northward, it is at least a possibility that it originally covered an area many times its present area.

Jan 10, 1926

By M. G. F. Sohnlein

IN a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. +20 8.0 +40 36.5 +60 9.0 +80 10.5 +100 5.5 +150 4.51 -150 25.0 99.0 Loss 1.0 IN the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.1 This remodeled classifier consists of a truncated pyramidal wooden hooper A with an attachment of cast iron

Jan 4, 1916