Search Documents

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By J. S. Aronofsky

The first step in a quantitative analysis ot the mechanism of oil displacement by water in a fractured reservoir is usually conceded to be the solution of the differential equation describing the saturation distribution of two immiscible fluids flowing in a porous medium, where the capillary pressure is taken into account. In such a system the production mechanism may consist of displacement of oil both by the flow of water due to natural or artificially imposed pressure gradients and by imbibition, which implies a flow of water not due to external pressure gradients. Owing to the presence of the two oil displacement mechanisms, the mathematical model given by the differential equation intended to describe the system may not properly represent the behavior of the physical system. In fact, in the reservoir the rate of water advance may be very slow, and in the case of a fractured reservoir with a great number of large fractures, the pressure difference determining the flow of water through the matrix may be much less than 1 lb/'psi over lengths of a few feet. In such a case, imbi-bition (the exchange between oil in the matrix and water in the fractures resulting from capillary forces) may become, with time. a significant element of the production mechanism. It occurred Lo the authors, however, that without going into a physical analysis of the process of production, it might be possible by means of simple abstract reasoning to throw some light on the variation of recovery with time under conditions occurring in a highly fractured oil reservoir with rising water table. The object of this paper is to present both the reasoning and its application to a reservoir of the highly fractured type. Specifically, the analysis given here was undertaken to try to explain the increase of recovery (as defined later) with time as observed in this reservoir, without having to assume unlikely variations in the reservoir parameters with depth. This attempt has been successful as will become clear upon comparison of the computed recoveries with the actual field data. ABSTRACT MODEL Let us consider a small volume. of porous matrix saturated with oil at time, t = 0. Let the process of oil displacement by water start at time, t = t,,. At some time, t, the process will have terminated. Then a volume of oil equal to or smaller than the original oil contained in the matrix will have been produced. The first basic assumption that describes the model and guides the forthcoming reasoning is that the oil production from the small volume. dv, is a continuous monotonic function of time and that it converges to a finite limit. Such an assumption is not inconsistent with the results of laboratory waterflood tests as well as with results of imbibition tests where this is, in fact, observed. The second basic assumption is that none of the properties which determine the rate of convergence change sufficiently during the process to affect this rate or the limit. Let it be assumed that the form of the function of time relative to production from the matrix volume. dv, is given by where V,(t) is the volume of oil produced up to that time t. R is the limit toward which the recovery converges, A is a constant giving the rate of convergence, and V,(t) is the volume of oil originally in place in the volume, dv. It should be noted that recovery at time I will be understood here to he It follows that r. tends to R as t tends to infinity. CONSTRUCTION OF RESERVOIR FROM ABSTRACT MODEL Let the reservoir consist of a series of identical blocks of porous matrix stacked vertically and separated by fractures. Let each of these blocks satisfy the conditions of our abstract model. These conditions are: (1) that recovery is a continuous mono-tonic function of time converging to finite limit, and (2) none of the properties that determine the rate of convergence change sufficiently to affect the rate or the limit. Let water be rising in fractures so that oil production from any part of the block starts when the water comes in conLact with it. TOTAL RECOVERY FROM THE RESERVOIR COMPARED TO RECOVERY FROM A SINGLE MODEL ELEMENT As stipulated in Eq. 1, in the case of the abstract model,

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.' The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898' C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.' The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898' C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By Irwin Roman

PART I. INTRODUCTION THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years, but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and. engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1931

By R. M. Treco

THE purpose of this work has been to investigate recrystallization characteristics of zirconium after cold working and annealing. In order to do this, hafnium-contain ing crystal bars of Foote Mineral Co. iodide zirconium were selected for high purity. maximum diameter (about ½ in.), brightness of surface, and absence of core wire. A typical lot analysis is shown in Table I. In order to obtain uniformity of starting material, all bars were cold-swaged to 0.310 in. diam, annealed for 2 hr at 1000°C, and furnace cooled.

Jan 1, 1957

By R. W. Heckel, R. E. Trabocco

The recovery process in 400 Monel filings was followed, principally, by using the Warren-Averbach technique of X-ray peak profile analysis. The deformation fault probability, a, was 0.006 in samples of unannealed filings. a , the twin fault Probability , was approximately 0.002 in samples of unannealed filings. Both a and 0 were found to "anneal out" at 600°F. The effective particle size and mzs strain increased and decreased in the (111) direction, respectively, with increasing annealing temperature. The actual particle size was found to be almost equivalent to the effective particle size. Tile small values of deformation and twin fault probabilities accounted for the similarity in values of the effective and actual particle sizes. Stored strain energy and dislocation density calculations based on rms strain decreased with increasing annealing temperature. The dislocation density decreased from 10" per sq cm in the unannealed filings to 10' per sq cm in the partially re-crystallized filings. The square root of the dislocation density based on strain to that based on particle size indicated a random dislocation distribution in the unannealed filings. The dislocation arrangement changed to one with dislocations in cell walls with increasing annealing temperature. THE recovery processes which occur in metals are generally thought to be a redistribution and/or annihilation of defects.' Investigators' have shown that recovery processes can be characterized by X-ray line-broadening analyses. Michell and Haig4 measured the stored energy of nickel powder by calori-metry and found the value to be greater by a factor of 2.5 than that from X-ray data obtained by the Warren-Averbach technique.= Minor increases in particle size occurred up to 752°F (recovery), while above 752°F the particle size increased greatly due to recrystalliza-tion. X-ray microstrain values decreased between room temperature and 392"F, remained constant from 392" to 752"F, and decreased from 752°F to a negligible value at 1112°F. Faulkner developed an equation for calculating stored strain energy based on X-ray line-broadening data which gave a closer correlation of measured and calculated stored strain energy based on the data of Michell and Haig. The stored strain energy released during recovery is predominately dependent on the decrease in dislocation density which was p-enerated from cold work.7 Stored energy has been measured8 in alkali halides during recovery and recrystallization and 80 pct of the stored energy was found to be released during recovery. Dislocation distributions have been studiedg in a number of fcc metals by thin-film electron microscopy. Howie and Swann" found the stacking fault energy of copper and nickel to be 40 and 150 ergs per sq cm, respectively. ~rown" has pointed out that these stacking fault energy values should be corrected to 92 and 345 ergs per sq cm, respectively. The dislocation distribution of a metal is directly dependent on the stacking fault energy of the system. Metals of high stacking fault energy such as aluminum cross-slip readily and do not form planar arrays of dislocations. Metals of lower stacking fault energy such as stainless steels" do not cross-slip readily. Cold-worked nickel has been found to form a cellular dislocation structure after annealing.13 The relatively high stacking fault energy of nickel and copperlo to a lesser extent favor cellular structures of dislocations rather than planar arrays after deformation. The present study of recovery was carried out on a Ni-Cu alloy (Monel 400) to compare with prior studies for pure nickel and pure copper. X-ray line-broadening techniques were used to measure the effect of recovery temperature on rms strain and particle size and the results were compared with previous studies on copper'4-'7 and nickel., Calculations were also made on stacking fault probabilities, dislocation density, dislocation distribution, and stored strain energy as affected by temperature. EXPERIMENTAL PROCEDURE The nominal analysis of the Monel 400 used in this investigation was: 66.0 pct Ni, 31.5 pct Cu, 0.12 pct C, 0.90 pct Mn, 1.35 pct Fe, 0.005 pct S, 0.15 pct Si. The annealed material was cold-reduced in two batches, one 50 pct and the other 80 pct. It was originally planned to conduct line-broadening studies of these bulk samples; however, rolling textures that developed produced low-intensity peaks which were not suitable for line-broadening analysis. Filings were prepared at room temperature from both the 50 and 80 pct cold-reduced specimens, series A and series B, respectively, and were not screened prior to heat treatment or X-ray studies. Heating to the annealing temperature, 200" to 120O°F, was accomplished in a matter of minutes in a hydrogen atmosphere. Following heat treatment, some of the filings were mounted and polished for microhardness measurements with a Bergsman microhardness tester, using a 10-g load. A G.E. XRD-5 diffractometer using nickel-filtered Cum radiation was used to obtain all diffraction patterns. Only (111)- (222) line-broadenin data were used in the present study since the {400f peaks were too weak to use. The Fourier analysis of the (111) and (222) peak

Jan 1, 1969

By Richard L. Stowe

Four NX-diameter holes were diamond-drilled in competent granite. Samples of the recovered core were used in laboratory tests. A borehole, plate-bearing device known as a Goodman jack was used to perform load deformation tests on the rock in the core hole. The majority of samples used in the laboratory tests were taken from depths in the hole at or within 5 ft of those at which the plate bearing tests were made. Borehole camera records, compressional and shear wave velocities, and densities were measured. Dynamic elastic constants were computed for the in-situ material, while comparative data (except camera records) were obtained in the laboratory. These data were examined to evaluate the significance of the in-situ modulus of deformation (Ed), the value computed from Goodman jack tests. Average test results show an excellent correlation between in-situ and laboratory data. The ratio of laboratory to field deformation modulus ranges from 9.82 to 7.21 for 3,000 and 9,000-psi stress levels, respectively. The dynamic modulus ratio, ED field/Ep lab, is 1.02; the compressional wave velocity ratio, V8 field/V8 lab, is 0.94; the shear wave velocity ratio, V, field/V, lab, is 1.12; and the density ratio, field [y/y] lab, is 0.95.

Jan 1, 1973

THOSE NOT MARKED ARE MEMBERS; MARKED THUS ?ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP JUNIOR MEMBERS ARE MARKED ' . THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD See Honor Roll. '05 ? AARONSON, ALFRED E Pres., Tuloma Oil Co., Unity Bldg., Tulsa, Okla. '18 ABADIE, EMILE R., Min. En r Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Fujitagumi Taiwan Office, Taipeh, Formosa, Japan. '14 ABBY, HIROSHI Min. & Met. Engr., Mitsubishi Co., Tokyo, Japan. '17 ||ABOUCHAR, S. S., Cia. de Minerales y Metales, S. A., Minas Viejas, Villaldama, N. L., Mexico. '17 ABRAHAMS, A. I 1391 Madison Ave., New York, N. Y. '14 ?ACKER, E. O'C., Met.,128 East Washington Lane, Germantown, Philadelphia, Pa. '86 ? ACKERMAN, ERNEST R., Pres., Lawrence Portland Cement Co., Plainfield, Union Co., N. J. '15 ACOSTA, J. N., Min. Engr., Cons. Engr Hotel Brewster, San Diego, Cal. '15 ADACHI, JINZOO 11 Shiba Park, Shiba-Ku, Tokyo, Japan. '88 ADAMI, CHARLES J., Min. Engr., Gen'l Supt., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12 ADAMS, ARTHUR K., Min. Geol., Andes Copper Min. Co., Casilla 230, Antofagasta, Chile. '06

Jan 1, 1923

By George W. Mitchell

THE property of Eureka Corp. Ltd. is located in the approximate geographic center of Nevada, 2 miles from Eureka, the county seat. The great sources of power, the Colorado, Snake, and Salmon Rivers and the rivers of northern California, are 300 to 500 miles distant, and no lines serve areas closer than 150 miles. Fuel for diesel and steam generation is available in Utah, 300 to 400 miles to the east. Eureka's railhead is 80 miles north where two trunk lines cross the county. A spur line serves Ely, 77 miles east. Good highways connect Eureka to the railheads.

Jan 8, 1953

By C. W. Goodale

As an appendix to the above-mentioned paper, a drawing of the vertical projection of the Knoxville mine workings is here given. In my paper it was stated that the ore-chimneys are found along a crack or plane of cleavage in the limestone ; and as this crack is not parallel with the strata, it is safe to assume that the manganese was not deposited where it is now found before the tilting-up of the strata, but rather that the crack was caused by the folding, and that tile formation of the ore was entirely subsequent to the change of position of the limestone. There are here four chimneys, which have produced, as far as explored, over 12,000 tons of ore, containing at least 7000 tons of manganese oxides, and it is very difficult to apply Prof. W. P. Blake's theory of segregation from the surrounding limestone in accounting for the origin of this ore, as cross-cuts and drifts in the countryrock, even at short distances from the ore-chimneys, have not shown manganese in appreciable quantities. It is easier to believe that, in the language of .Mr. S. F. Emmons, in speaking of Leadville ore-deposits, there was a metasomatic interchange between the minerals brought in in solution and the limestone, and not a deposition in already existing cavities. This in-

Jan 1, 1890

By Frank Fahrenwald

INTRODUCTORY A COMPLETE list of the elements as given for 1915 includes 18 that melt above 1,700° C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure .metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures* and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,1 of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation.

Jan 6, 1916

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965

By P. A. Beck, Hsun Hu

As described by means of quantitative pole figures, the annealing texture of highly rolled aluminum consists of the four retained components of the rolling texture near (123) [121], rather more sharply developed, and of a cube texture component. Local reorientation corresponds fairly well to 40 rotation around a [111] axis. In copper strip rolled 96 pct, the annealing texture is mainly the cube texture, with the four twin orientations as minor components. The annealing texture of highly rolled brass strip consists of four components of the (225) [734] type. REVIEWS by Wassermann,' Barrett,' Dunn,3 and Richards' give detailed accounts of the numerous publications dealing with annealing textures in rolled polycrystalline metals. Although a considerable amount of information of an empirical nature has been available for many years, even relatively recently the state of recrystallization-texture theory was considered uncertain. The reviews referred to above deal mainly with the description of experimental results, without developing generally applicable principles, suitable for explaining the observed annealing textures. The investigations of Burgers and Louwerse5 and Barrett6 showed that in deformed single crystals of aluminum the orientation of the recrystallized grains deviates drastically from that of the deformed matrix. According to Barrett and to Beck and Hu,7 the relationship between the two orientations can be best described as a rotation of about 40° around a [111] axis. Recent investigations led to similar orientation relationships for various face-centered cubic metals with a simple texture, regardless of whether the annealing process was recrystallization (strain-free grains growing in a highly deformed large crystal of aluminum' or copper: or in deformed cube texture copper") or coarsening (strain-free grains growing at the expense of an essentially strain-free, fine grained, polycrystalline matrix of single orientation texture copper,'" aluminum,' or nickel-iron). Barrett" pointed out the possibility that this orientation relationship may be a result of the orientation dependence of the rate of grain boundary migration. More recently, considerable evidence became available in favor of this view.12,13 In apparent contradiction to the above results, it has been known for a long time that the recrystallization texture of polycrystalline metals is often similar to the deformation texture. This was found, in particular, for the fiber textures obtained by wire drawing, compression, or compression rolling.' Following a suggestion by Barrett,2 Kronberg and Wilson and Beck and Hu7 described a mechanism by which a [Ill] fiber texture, resulting from plastic deformation, may be retained upon recrystallization, even though the orientation of individual recrystallized grains differs from that of the local area of the matrix in which they grow. This mechanism assumes that the reorientation corresponds to a rotation around the [1ll] axis, which is also the fiber axis. The present investigation was undertaken to examine in detail the orientation relationship between deformation texture and recrystallization texture in rolled face-centered cubic metals, using the quantitative methods of texture determination that have recently become available.", '" Quantitative pole figures for the rolling textures of such metals were reported recently." Quantitative pole figures for annealing textures are given in the present paper. It was planned to investigate whether or not the orientation relationship previously found for the recrystallization of deformed single crystals, and for coarsening of single-orientation texture material, is capable of accounting for the observed, often complex, annealing textures in rolled polycrystalline metals. The question whether local reorientation is predominant, even in the early phases of the annealing process, was to be studied with high purity aluminum. by making use of an oxide film and sensitive tint illum-

Jan 1, 1953

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944