Search Documents

By Arthur F. Taggart

RECENT jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out of the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely different ways, depending upon the relative sizes of the grains presented to it and those composing it. EXPERIMENTAL The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. C. Dorenfeld, a student in the Mining Department at Columbia. Spheres of different metallic alloys, Y8-in. diameter, were cast with a short piece of fine copper wire frozen in to serve for suspension. A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs. 2 and 3. DEFINITIONS The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a shorlrange product is one closely sized. A bed is loaded when operating with continuous feed

Jan 1, 1943

By O. N. Carlson, K. E. Solie

The brittle-ductile transition temperatures of single and poly crystalline chromium metal were studied as a function of nitrogen concentration and chromium nitride distribution. It was observed that In recent years there has been an increasing interest in chromium-base alloys for high-temperature applications. The principal disadvantages, however, have been the difficulties of fabrication and the design problems associated with a material of such limited ductility. Various studies have been the effects noted in the poly crystalline material are essentially reversed in the single crystals. These observations are discussed in terms of existing theories for the brittleness of chromium. conducted recently directed toward a determination of the cause of this brittleness and to find ways for minimizing its effects. Allen et al.,' Wain Abrahamson and rant,' and weaver4 have carried out studies on the effects of interstitial impurities on the brittle-ductile transition of chromium metal of various degrees of purity. These investigations have shown that oxygen has little or no effect on the transition temperature of chromium in all conditions studied but that carbon increases the transition temperature under all conditions tested. Nitrogen was found to increase the transition temperature in the wrought condition and in the quenched or cast conditionS but reportedly has no effect in the furnace-cooled condition.

Jan 1, 1964

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By Douglas Bunting

The first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel. Although, as far as we know, the accidents of the past have not resulted in the loss of life, except in two instances, yet nearly all were attended with more or less miraculous escapes of men working in the vicinity of the breaks, so that the probable existence of pot holes, etc.,

Jan 1, 1915

The following list comprises the names of those persons who became members during the period Sept. 10, 1919, to Oct. 10, 1919. ADAMS, R. L Chief Min. Engr., Old Ben Coal Corpn., Mine 12, Christopher, Ill. Arizumi, Hiroshi The Kuhara Min. Co., Ltd., Tokyo, Japan. BAILY, T. F Pres. & Gen'l Mgr., Electric Furnace Co., Alliance, 0. BALDWIN, A. J., Min. Engr Box 145, Pikeville, Kentucky. BALTZELL, WILL H., Chief Engr., Canadian Steel Corpn., Ltd., Ojibway, Essex Co., Ont., Canada. BANON, E. MAGAWLY, Examining Engr., Dawes Bros., Inc. 108 So. LaSalle St., Chicago, Ill. BARNES, W., Mech. Engr., Excavating Dept., Ruston & Hornsby, Ltd., Lincoln, England. BASHORE, E. GORGAS, Head Chem., The Babcock & Wilcox Co., Bayonne, N. J. BASS, A. L Supt., Hobson Silver Lead Co., Ltd., Ymir, B. C., Canada. BORN, SIDNEY, Chief Chem., Empire Gas & Fuel Co. & Associated Companies, 1100 Cherokee Ave., Bartlesville, Okla. BRADLEY, J. G,, Coal Operator, Pres.,& Gen'l Mgr., Elk River Coal & Lumber Co., Dundon, W. Va. BENNETT, G. W., Min. Engr., Sales Engr., Taylor-Wharton Iron &- Steel Co., High Bridge,. N. J. BRUFF, CHARLES E., Member firm Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. COLLINS, FRANK W., Chief Engr., Bradley, Bruff & Labarthe, 85 Second St., San Francisco, Cal. CONNELL, F. M., Min. Engr., Eastern Alin. & Mill. Co., Ltd., 905 Bank of Hamilton Bldg., Toronto, Ont., Canada. CooK, HARRY H., Vice-pres., Valley Mould & Iron Corgn., 137 Shenango St., Sharpsville, Pa.

Jan 11, 1919

By Walther Mathesus

INTRODUCTION THE use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100° F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800° and 1,000° F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available.

Jan 3, 1915

By G. S. Hume

The largest development program in the history of Alberta was undertaken in 1941 in an effort to increase oil production. The drilling record is as follows: In Alberta there was the largest exploratory campaign for oil in the history of the Province, although drilling of wildcat wells was somewhat less than in the previous year. A great deal of geophysical work was done. This included three gravimetric and five seismic parties as well as a number of geological survey parties by the major oil companies and by the Geological Survey of Canada. Seismic work was done by one party in southern Saskatchewan. The production of petroleum in Canada is shown in Table I. About 98 per cent of the total production comes from Alberta and the yield of the various fields is shown in Table 2. The greatest developments in Turner Valley have been in the north end. In 1941 about two miles of new productive area was proved by drilling, extending the field to a length of 20 miles. The wells at the

Jan 1, 1942

By G. S. Hume

The largest development program in the history of Alberta was undertaken in 1941 in an effort to increase oil production. The drilling record is as follows: In Alberta there was the largest exploratory campaign for oil in the history of the Province, although drilling of wildcat wells was somewhat less than in the previous year. A great deal of geophysical work was done. This included three gravimetric and five seismic parties as well as a number of geological survey parties by the major oil companies and by the Geological Survey of Canada. Seismic work was done by one party in southern Saskatchewan. The production of petroleum in Canada is shown in Table I. About 98 per cent of the total production comes from Alberta and the yield of the various fields is shown in Table 2. The greatest developments in Turner Valley have been in the north end. In 1941 about two miles of new productive area was proved by drilling, extending the field to a length of 20 miles. The wells at the

Jan 1, 1942

Because common salt, sodium chloride, is necessary to all animal and much plant life, it is probably the most widely used of all mineral commodities, except for water. Nevertheless, of the total salt consumed, only 7% is used for food, including animal food. Two-thirds of the total is used as chemical raw material, principally for making such basic chemicals as chlorine, caustic soda, and soda ash. Other uses are for road thawing (16%) and water softening. Some 162.5 million tons of salt were used, worldwide, in 1972 (Table 15.4F.1). Production is from bedded salt deposits, salt domes, and evaporation of brines, including solar evaporation of seawater. Production is worldwide from at least 20 countries, of which the United States, China, USSR, the United Kingdom, and West Germany are the leaders. Consumption increases about 7 % annually. Reserves are plentiful: Other important sodium salts are soda ash (sodium carbonate) and salt cake (sodium sulfate). Soda ash comes mainly from the Solvay process (70% ) , which uses salt, limestone, and ammonia as raw materials. A large and growing portion of United States production is from mining large bedded deposits of trona, a natural hydrated sodium carbonate and bicarbonate found in Wyoming, and from brine evaporation in California. Soda ash is used for glassmaking, phenol, soap, detergents, and bleaches. Half of the United States salt cake used is a byproduct from rayon manufacturing. The other half comes from brines and playa lakes in California, Texas, and Wyoming. Salt cake is used mainly for papermaking. ACKNOWLEDGMENT Appreciation is expressed to William B. Dickson, president, Salt Institute. [ ]

Jan 1, 1976

Jan 1, 1920

By V. R. Garrias, R. V. Whetsel, J. W. Ristori

World consumption of petroleum and its substitutes in 1940, which, except for the United States, does not include consumption for military purposes even in peacetime, is estimated at 2,006,000,000 bbl., or approximately 21,000,000 bbl. less than in 1939. As consumption figures for belligerent countries and those affected by the war are unavailable, in order to arrive at a gross approximation the assumption has been made that the rate of civil consumption in these countries has declined 80 per cent since the German occupation or the effect of the war made itself felt. In 1940 the total consumption in the United States increased 94,000,000 bbl. over the previous year, while the civil consumption in the countries directly affected by the war—some of them occupied during the last half of the year—decreased 126,000,000 bbl. In the rest of the world consumption increased II,000,000 bbl., resulting in an over-all decrease in world civil consumption grossly estimated at 21,000,-000 barrels. Although no reliable information is available regarding military consumption in foreign countries before or during the war, military consumption and/or addition to stocks in foreign countries in 1940, as

Jan 1, 1941

By J. W. Ristori, R. V. Whetsel, V. R. Garrias

World consumption of petroleum and its substitutes in 1940, which, except for the United States, does not include consumption for military purposes even in peacetime, is estimated at 2,006,000,000 bbl., or approximately 21,000,000 bbl. less than in 1939. As consumption figures for belligerent countries and those affected by the war are unavailable, in order to arrive at a gross approximation the assumption has been made that the rate of civil consumption in these countries has declined 80 per cent since the German occupation or the effect of the war made itself felt. In 1940 the total consumption in the United States increased 94,000,000 bbl. over the previous year, while the civil consumption in the countries directly affected by the war—some of them occupied during the last half of the year—decreased 126,000,000 bbl. In the rest of the world consumption increased II,000,000 bbl., resulting in an over-all decrease in world civil consumption grossly estimated at 21,000,-000 barrels. Although no reliable information is available regarding military consumption in foreign countries before or during the war, military consumption and/or addition to stocks in foreign countries in 1940, as

Jan 1, 1941

By John E. Sherborne, William M. Newton

THE relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resistivity of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity.

Jan 1, 1942

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By C. R. Woodcock, J. S. Mason

In almost any situation where particulate or granular bulk solids have to be conveyed, whether for a distance of a few metres or for many hundreds of metres, a pneumatic conveying system may be considered. Conveying by pipeline is convenient and clean, but running costs may be substantial because of the heavy air consumption and the trend has therefore been towards dense-phase transport in which the ratio of conveyed solids to conveying air is kept high. This paper concentrates on air-float conveying, which can be regarded as an extreme form of dense-phase conveying where the bulk solid is fluidised in a channel and then caused to flow, either by inclining the channel or creating a pressure gradient along 'it. Various designs of air-float conveyor for upward, horizontal and down- ward transport of powders are discussed, with special emphasis on the latter case. In situations where a continuous downward slope can be provided, the combination of air-fluidisation and gravity flow results in a conveying system that, for many kinds of bulk particulate solid, would be hard to better in terms of convenience, reliability and economy. The paper is concluded with a discussion of design features and performance of practical air-gravity conveyors, involving the handling of various bulk particulate solids, both in research and in full-scale industria1 applications.

Jan 1, 1980

C. P. SANDBERG, LONDON, ENG : † I think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr., Dudley, for spending so much time and money in order to solve an important question ; nor are we less indebted to the public spirit which leads them to impart the experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; but even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails-tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper, a paper which follows very much upon the same lines of argument as the first read three years ago, upon which I have previously touched in my paper on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken more pains to prove that he was correct in his first formula for the best chemical composition of steel rails. But I have seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by samples. If Dr. Dudley would only give up his formula, which would not suit any country-not even America- * For the convenience of members it has bees thought best to insert the continuation of this discussion at the Virginia meeting in tide place, rather than to delay its permanent publication until the issue of Volume X, Transactions, where it would properly belong. T. M. D., Sec'y, † Sent to the secretary in manuscript.

Jan 1, 1881

By Bob J. Rawicki

TYPES OF WET DUST COLLECTORS Basically, there are two types of wettype dust collectors. One is mechanical, incorporating pumps, motors, fans, sprays, filters, or flooded beds. These come in many forms, but their operating principle is basically the same. The screen or flooded bed is wetted by a series of sprays. Polluted air is drawn in through a fan; here the dust particles impinge on the screen and are flushed off into a settlement tank. The air then passes through spray eliminators to the atmosphere. A great deal of time and money has been spent developing this type of collector. In laboratory tests where clean water at constant pressure, air at constant volume, and dust at low but constant mass to volume were applied, these collectors gave high percentage dust collection efficiencies. Theoretically and technically, they are very good. In practice, however, under rugged mining conditions where there are no constants, and dust load, particle size, water pressure, and volume of air vary with time, their efficiency varies dramatically. Some of the most common problems are: 1. clogging of screens 2. blocking of nozzles 3. replacement. of damaged pump stators Any of the above result in loss of air flow and dust collection efficiency. Generally, there are so many mechanical moving parts, something is always breaking down. This type of collector is very expensive in parts and labor to maintain. The second type of dust collector, which I personally developed, with the help of the British National Coal Board of Great Britain, has none of the above mentioned problems and it works on a completely different principle. My collector, the Mark III Precipitaire Wet-Type Dust Collector, (an improved version of previously successful models) has no internal moving parts, no flooded beds, screens, spray nozzles, etc. It is highly efficient - 99.8% efficiency on total collected dust and 97% on respirable dust. The pressure drop through the collector is constant, hence, air flow remains constant. There is no maintenance expenditure, be it labor or parts. The only maintenance that there is, is desludging. This, of course, varies with the dust load. With a low dust load, desludqinq may only be required every 4 weeks, but this is a very simple operation that can be handled by unskilled men and it takes only a very short time. My collector is powered by a ventilation fan that is placed on the clean air side for a longer fan and motor life. Dust is extracted solely by water action. The collector's operating principle is: Dust laden air is drawn in along ducting into a tapered scrubber section, shaped to create a self-induced curtain of water. This action washes the dust particles from the air and the collected dust settles into the bottom of the tank. Cleaned air is then exhausted via a series of spray eliminators where it is completely dried and on into the atmosphere. These collectors have been sold in Great Britain, to the National Coal Board, and throughout Europe. They have been working very well for many years now. GENERAL APPLICATIONS Dust is very dangerous; silicosis and black lung kill and disable many workers each year. Many of the mine explosions can be attributed to coal dust. By the use and application of dust collectors, these deaths and disasters can be avoided. There really is no excuse. However good and efficient a dust collector may be, it's positioning and installation arrangement is critical. The collector may remove 99% of dust supplied to it, but it takes the skill and experience of a dust control engineer to design and fit ducting, hoods, etc. to remove polluted air at source and deliver it to the collector. In some cases this is very simple; in the case of longwall machines, it is very difficult. In general, dust collectors should be used to collect dust at every point of dust generation. I have noted a great reliance on dilution as a means of dust control. I personally think this is a dangerous and unreliable method. As mines become deeper and the use of larger and more productive equipment becomes more common, reliance on dilution will be impossible and dust collectors will be essential.

Jan 1, 1982

By G. H. Rowe, A. N. Stroh, D. P. Gregory

The magnitude and variation with strain of the parameters activation volume, V*; activation energy, H; and frequency factor, A, in the Arrhenius equation for strain rate are determined for colunlbium single crystals and polycrgstals. Comparison of dislocation structures in deformed columbium crystals as determined by transmission electron microscopy with the rate IF deformation of a metal crystal is a thermally activated process, rate theory can be used as a powerful tool in the study of dislocation mechanisms. seeger1 develops the following expression for plastic deformation governed by a single thermally-activated theory results suggests thai formation of lattice vacancies at jogs in screw dislocations is responsible for thermally activated deformation of poly crystalline columbium. Single crystals appear to deform by a different mechanism. Work hardening in fully recrystallized fine grain columbium is found to result from simultaneous decrease in activation volume and in the number of mobile dislocations with increasing strain. Work hardening in recovered polycrystals is found to result from decrease in activation volume with strain only. dislocation mechanism. His equation for strain rate is where N is the number of mobile dislocations per unit volume held up at energy barriers, v is the frequency with which the dislocations "try" the energy barriers, b is the Burgers vector, a is the area a dislocation loop sweeps out after overcoming a barrier, V* is the activation volume which will be defined more completely later, and t* is the thermal component of stress equal to (Ta-Ti), where Ta is applied shear stress and Ti is internal stress of the dislocation network17' given by

Jan 1, 1963