Search Documents

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By William B. Plank

ENGINEERING students to the number of 73,269 had been enrolled in United States and Canadian schools on Nov. 5, 1945, but, as shown in the following tables, even this sizable number will not greatly remedy the 150,000 deficit reported by Vannevar Bush, director of the U. S. Office of Scientific Research and Development, to exist in the engineering and scientific man-power supply. These figures were received in advance from the Society for the Promotion of Engineering Education, and are given in detail in the January 1946 issue of the Journal of Engineering Education. Although the enrollment on Nov. 5 was an increase of 76% over the low of 41,632 in 1944-45, it was still 36% below the peak enrollment in 1941-42 of 115, 228. These figures include both undergraduate students and graduate students in the schools of the United States and Canada and are therefore comparable. As was to be expected, almost half of this enrollment is in the first or freshman year and 25% of the total are veterans. Also, 1,850, or about 2.5%, are women. A measure of the seriousness of the engineering graduate supply in these two countries is indicated by the trend of the number of first degrees that have been conferred during this period of scarcity:

Jan 1, 1946

By Charles H. Behre

KEYNOTE of the mining geology sessions was the preparation for an extensive war with all that this implies as to the need for strategic minerals, both metallic and nonmetallic. Nevertheless the sessions also included many papers of less urgent, more theoretical interest. The stress of wartime production had the effect of giving an unusually full and rich program, the longest in recent years, with sessions continuing virtually throughout the meeting. Some papers dealt with geophysical prospecting as applied to mining geology; others were concerned with the grand strategy of mineral reserves and thus involved the industrial minerals; such "borderline" subjects were presented before sessions held jointly with the Geophysics Committee or the Industrial Minerals Division.

Jan 1, 1942

By AIME AIME

A THOROUGHLY satisfactory crowd turned out at the fall meeting of the Industrial Minerals Division and took an active part in the entire program. On Thursday afternoon, Sept. 24, a limestone plant was inspected, technical sessions occupying the attention of the visitors all day Friday and Saturday morning. Headquarters were at the Nittany Lion Inn, an attractive hostel on the Penn State campus, at State College, right in the center of Pennsylvania. We are still in the dark, despite inquiries, as to just what breed of lions Nittany lions are. As nearly as we could find out, Nittany is not a Biblical name, as it sounded to us, but a corruption of the name of an Indian princess, or maiden, or maybe just girl that haunted those parts in bygone times and after whom a near-by mountain was named. Penn State athletes are "lions" and there you are. The meeting was supposed to be a joint one with the American Ceramic Society's Materials and Equipment Division; but it was quite evident that the Institute had a much better publicity agent than the Society, which bothered Ross. Purdy, the aggressive secretary of the ceramic people, no end. However, Secretary Purdy saw to it that everyone present fully understood that the Ceramic Society was present, so that that contingent all but stole the show, its representatives presiding at every meeting. The Pittsburgh Section of the American Ceramic Society was also supposed to be holding its fall meeting there at the same time, but made no trouble at all for anybody, as one of the speakers remarked.

Jan 1, 1936

By Harold F. Unger, Byron S. Snowden, William H. Engelmann

The effects of using surfactant solutions while diamond drilling in amygdaloidal basalt of the Upper Michigan copper mining district were investigated. Nonionic, anionic, and cationic surfactant solutions, all biodegradable, were tested with size AX surface-set bits mounted on a drill instrumented for continuous recording of thrust, rotational speed, and torque levels. Water flow and penetrations rates were also recorded. A drilling study was carried out, testing two rotational speed levels, two diamond bit grade levels, and four flushing agents (including water as a control). Comparison of all low-speed/high-thrust groups of tests shows that the non-ionic surfactant produced a 35% overall average increase in penetration rate over water, the anionic a 29% increase, and the cationic a 28% increase. These increases in, penetration rates resulted in a 22 to 26% reduction in cost over flushing with water alone. With the high-speed/low-thrust combination, the surfactants produced less benefits in penetration rate increases over water (14% increase for nonionic, 14% decrease for anionic, and 2% decrease for cationic type). Particle size analyses were run on drill cuttings produced by the three surfactant solutions and by water. All surfactant solutions showed a 20 to 50% increase in solids content over that of water alone. Since flushing rates were constant, these increases in solids content agree well with the penetration rate changes. The diamonds were recovered from each bit by matrix dissolution, and bit wear was measured in terms of total loss of weight. Flushing with surfactant solutions showed a savings in bit wear in most cases. The drill team noted also that surfactant flushing improved recovery of drill core by allowing easier removal of the core from the barrel.

Jan 1, 1976

By AIME AIME

EVEN the weather man joined in a friendly conspiracy to make the fall meeting of the Industrial Minerals Division at Rolla, Mo., Oct. 23-25. the splendid surges that it was. Following weeks of rain, the foliage of the Ozarks was still green, merely enlivened here and there by splashes of autumn coloring. In contrast to the tranquil beauty of the School of Mines campus under smiling Indian summer skies, the pace of the meeting was lively. Registration was larger than at any previous meeting and included an unusual number of prominent names and delegates from all over the country. From 125 to 150 were present throughout the three technical sessions, at the Thursday evening smoker, and also at the banquet on Friday; when students trooped in to the technical sessions the audience was augmented occasionally to over 200.

Jan 1, 1941

By Kent R. Van Horn, W. P. Sykes

Since Honda and Murakamil in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450° C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450" and 1000" C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000" C. and heated for 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt's second intermediate phase. While Takeda failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200" and 1450" C. no evidence of the second phase (Fe2W) was observed 'either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1933

By WILFRED SYKES

IT is with particular pleasure that I welcome the members of the Open-hearth Conference of the I American Institute of Mining and Metallurgical Engineers to this meeting, as I feel this is one of the most useful activities of the Institute in the field of ferrous metallurgy. For the information of our other members I might say the Open-hearth Conference was organized by Mr. Reynders when he was president, and is made up of open-hearth superintendents and metallurgists. All the plants are invited to send representatives, and practically all do, with the exception of the U. S. Steel Corporation. It meets twice a year to discuss various problems in connection with the manufacture of steel, and its minutes are published for the benefit of those attending, the expense being defrayed by the participating companies. This conference, .1 believe, should be a model for activities in the other branches of the work covered by this Institute. It works, not by reading formal papers, which we all know is not a very satisfactory method to bring out the experience of others, but rather by a round-table method of discussion. The spirit of the meetings is such that each member feels perfectly free to state his experience, and he gets as much as he gives. A series of topics for, discussion is brought to the attention of the chairman and after one is exhausted the next point is taken up. In this way there is a real interchange of ideas and experiences which cannot fail l to be of the greatest benefit to those attending. That these meetings are beneficial is evidenced by the "continued growing attendance and lively discussions at these half-yearly meetings.

Jan 1, 1930

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By J. French Robinson

A review of production in the Eastern District for 1930 is necessarily brief. Drilling operations were curtailed, due to economic conditions, which in turn reduced production. However, in spite of these conditions, there have been a few outstanding developments which surpass any of recent years. The development of a field in Chautauqua and Cattaraugus counties, New York, has been rapid and probably reached its peak of production in 1930. The gas in this field comes from the White Medina Sand (Silurian), at an average depth of 2600 ft. Some of the wells had an open flow of 20,000,000 cu. ft. of gas per day,' with an original rock pressure of 965 pounds2 per square inch. Another area developed during 1930 was the Tyrone field, in Tyrone Township, Schuyler County, New York. This field was discovered 2nd is practically controlled by the Belmont Quadrangle Drilling Corpn. of New York. The production is from the Oriskany Sand (Devonian), which is found at an average depth of 2100 ft. The field covers approximately 2000 acres, and to date has 14 producing gas wells. The largest well had an open flow of 15,000,000 cu. ft. and an original rock pressure of 740 Ib. The gas from this field is impregnated with sulfur, and requires washing before it is marketed. Because little is known of the Oriskany Sand, a brief description may be of interest. This sand outcrops at Oriskany Falls, New York, and has a thickness of 10 to 12 ft. Its texture is coarse grained, it is composed mostly of quartz and is a regularly bedded sandstone. At Yauger's Wood, in Cayuga County, New York, it is exposed and shows a thickness of 26 feet. The discovery of the Tyrone field led to much prospecting in the New York and the northern part of Pennsylvania, and as a result of this search, the Allegany Gas Co. struck a large gas well in Farmington Township, Tioga County, Pennsylvania, which created considerable excitement through the Eastern District. The gas was encountered at a depth of 4010 ft., and tested 20,000,000 cu. ft. open flow, with a shut-in pressure

Jan 1, 1931

By Francis A. Thomson

IN reviewing mineral industry education a year ago, occasion was taken to congratulate the Institute in general and to felicitate the Education Di- vision in particular on "the most gratifying growth which is taking place in Institute consciousness in regard to its responsibility for the recruitment and adequate training of student personnel and for the successful bridging of the difficult gap between graduation and achievement of professional status." Continuation of this growth of interest throughout 1939 is a recognition of the validity of the splendid statement of George Otis Smith that the mining students of today are the ore reserve of the Institute for the future. In this connection one recalls the equally apt expression of another distinguished geologist, George M. Fowler, who, speaking of exploration for ore deposits, says, "The place to look for elephants is where elephants have been found."

Jan 1, 1940

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Gerhard Derge, Harold Markus

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By Harold Markus, Gerhard Derge

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By AIME AIME

IN ORDER to carry on its work most effectively, the Committee on Industrial Organization (now known as the Committee on Industrial Relations) consists, of .a number of sub-committees, each composed of a chairman and members who are especially fitted to carry out the work designated by its title. With only one or two exceptions, all of these committees made reports at the New York meeting of the Institute, in February of this year, abstracts of which follow.

Jan 1, 1920

By E. A. Gulbransen, W. S. Wysong

The behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance. The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotec-tive nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance studyl, 2 of the following problems: (I) the oxidation kinetics in the temperature range of 250°to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films; and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 2 50°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide Moo3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics: time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation. The general interpretation of many of these factors has been previously discussed. Literature The oxidation of molybdenum has not been studied critically. Although many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Gulbransen." Their results showed that Moo2 is the oxide which is stable in contact with the metallic substrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Moos is no longer observed, MoO2 being the only oxide found. Hagg and Magneli6 have shown from an X ray study that the a-phase, orthor-hombic Moo3 is stable up to 1050°C. Two other phases, ß and ß with compositions close to MoO2.90 are also obtained. The formula for the 0 phase is not given but that of the ß phase is defined as Mo9O26 The 0' phase is found to be built upon a monoclinic unit cell. A ?-phase is isolated from a preparation MoO2.75 heated for 17 hrs at 670°C. This phase is

Jan 1, 1949