Search Documents

By Kenyon E. Richard, James H. Courtright

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial de- lineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper.

Jan 11, 1954

By A. F. Brock

The cut-and-fill mining methods in use in the mines of The International Nickel Company of Canada Limited, at Falconbridge Nickel Mines Limited, in the Sudbury District, and at McIntyre Porcupine Mines Limited in the Porcupine District, are typical of the general cut-and-fill practice in both the base-metal mines and the gold mines in the Province of Ontario. The following pages describe the methods in use. HORIZONTAL CUT-AND-FILL STOPING Horizontal cut-and-fill stoping, as practiced in the mines of The International Nickel Company of Canada Limited, falls into two main classifications: (I) transverse cut-and-fill stoping, where ground conditions or wide ore bodies make it necessary to establish narrow stopes and pillars across the width of the ore body; (2) longitudinal cut-and-fill stoping where ore body widths and ground conditions allow safe mining of the full width of the ore body. Transverse Cut-and-fill StopiNg General Stoping Layouts Stope and Pillar Widths.—For transverse stoping, experience has indicated that narrow stopes and pillars, 27 ft. 6 in and 22 ft., respectively, are most satisfactory. These width are multiples of 5 ft. 6 in., which is the center to center dimension of a standard square set. Thus any stope, or block of stopes, can be readily converted from cut-and-fill to square set-and-fill if ground conditions should warrant such a change. Formerly, pillars were established 16 ft. 6 in. wide, the equivalent of the width of three square sets, with the intention of extracting the pillars by mining an overhand slice one set wide and an underhand slice two sets wide. However, subsequent experience proved that a two-set overhand slice is so much more efficiently mined than a one-set slice, and 22-ft. pillars have been made standard. Chutes.—The stope chutes are established on the longitudinal center line of the stopes and are spaced at 22-ft. centers from footwall to hanging wall. The footwall chute is usually from 5 to 10 it. from the footwall of the stope. It is offset where necessary at an angle of 52° and vertical chutes are carried from the offset at 22-ft. centers. In sections of the ore body where a flat hanging wall would cut off hanging-wall chutes within a few cuts of the sill, it has proved to be more economical to use temporary chutes or slushers, or both, for these first few cuts, rather than to el permanent chutes at the hanging wall.

Jan 1, 1946

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condi-tion, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organiza-tions of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements.

Jan 1, 1938

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-The most important criterion on which judgment of the quality of manganese bronze can be based is its freedom from lead. Not over 0.03 per cent. of lead should be present in a good grade of manganese bronze. While it is not questioned that manganese bronze with a high tensile strength and considerable ductility can be made .from materials that will give a lead content of possibly 2 to 3 per cent., there is no doubt that such material, while it may machine readily, will be found to withstand the impact test very poorly, and hence be unsuited for high-grade engineering work. When lead is present in considerable amounts, it forms in small pools in the alloy and the material has little strength at these points; in fact, such spots in the metal are equivalent to nicks in a test bar as far as their effect on tensile strength is concerned. A further objection to a high lead content is the ease with which it oxidizes and its consequent tendency to produce dross. A second characteristic of a high-grade manganese bronze is a low content of manganese. This should not exceed 0.05 per cent.; in fact, very many of the best grades of manganese bronze show, on analysis, only a trace of manganese or no manganese whatever. Manganese is a deoxidizer and its ready oxidation protects the other metals of the alloy; but if it is present in large amounts it will produce considerable manganese dioxide, which does not separate readily from the molten alloy and may produce black specks or drossy spots and render the obtaining of clean castings difficult. Aluminum should be present in a good grade of manganese bronze in only very small amounts. A content of 0.10 per cent. aluminum is ample. Larger amounts have a tendency to increase the shrinkage of the alloy, to give the ingots and castings a white, scruffy appearance, and to prevent the beautiful, golden, oxidization color characteristic of high-grade manganese bronze and a most excellent indication of quality. The work that the author of the paper has done is valuable from a con- servation standpoint, and it will supplement, in a marked degree, the advances that have been made by a number of manufacturers of manganese bronze in utilizing the turnings from this material. A number of firms have succeeded in making a very good grade of ingot metal from turnings and other light scrap, obtaining a tensile strength and elongation

Jan 4, 1919

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930

By W. E. Gaby

SINce the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. , The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,' Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the " Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down. The investigation was based on specimens furnished by B. Magnus, former general manager of the mine, and notes on the areal geology by

Jan 1, 1917

By J. L. Brimhall

Slip-line formation during bending has been studied on neutron-irradiated molybdenum single crystals. For equivalent strains, the slip lines are coarse and distinct in the irradiated molybdenum and not resolvable in the unirradiated molybdenum. The slip lines have been directly correlated with dislocation channels present in the irradiated and deformed thin foils. The heterogeneous distribution of the dislocations during deformation in the irradiated material results from dislocation interaction with the dejects produced during irradiation. Impurities , in the form of' carbides, affected the dislocation channeling Principally by acting as dislocation sources. ALTHOUGH the mechanical behavior of irradiated materials has been studied extensively, the precise mechanism of irradiation hardening has not been established. Some information on the microstructural species responsible for hardening of irradiated materials has been derived from direct and indirect observations. The direct observation of the structure of deformed irradiated metals, particularly by transmission electron microscopy, is a relatively new and unexplored area. Slip-line studies in fcc metals have been restricted primarily to copper.1-3 Very coarse slip lines, representing slip on many closely spaced planes, have been observed in deformed, irradiated copper. Coarse slip lines have also been observed in irradiated aluminum.4 Clear channels in irradiated copper caused by dislocation motion through the defect structure have been seen by transmission electron microscopy and correlated with slip lines.5-6 To date, little work has been reported on the irradiated bcc metals. Eyre described the slip lines around hardness indentations on irradiated iron and found them to be more distinct than lines in unirradiated material.' Mastel et al.' have observed channels in deformed irradiated molybdenum similar to those reported in copper. As part of a program concerned with the effect of neutron irradiation on metals, the slip-line

Jan 1, 1965

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators '-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By Kendall E. Born

Production of crude oil in Tennessee during 1942 was approximately 8600 bbl., a decrease of 6500 bbl. from the production of 1941, and the lowest since 1934. As usual, the greater part of the production was from the Mississippian limestone pools in Scott and Morgan Counties. Some half dozen wells in Fentress and Clay Counties pumped intermittently produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas respectively. Figures are not available for the Morgan County production but 7,378,000 cu. ft. of natural gas was produced in the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Developments Drilling activities reached the lowest ebb since 1933. Only 10 wells were spudded during the year, one of which was drilling on Dec. 31, 1942. Of the nine completions, two were gas wells in the proven area south of Jamestown in Fentress County and seven were dry holes. The total footage drilled during the year was 14,198 ft.; the average depth of wells was 1578 ft. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 4219 ft., the second deepest well in the state, in Campbell County. The test was in the highly disturbed Valley and Ridge Province, an area long considered the most unfavorable in the state for the accumulation of oil and gas. Cumberland Plateau.-—There were no completions in the Cumberland Plateau area, although an old well drilled deeper found oil from 935 to 965 ft. in the Mississippi lime. This test has created a considerable amount of interest in the area and an active leasing campaign was underway early in 1943. Eastern Highland Rim.—Five completions on the Eastern Highland Rim brought in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area were drilled to the upper part of the Knox dolomite group. The most significant test during the year was the Stanolind Oil and Gas Company's test in Putnam County. This well, on a well-defined surface structure, was abandoned in the upper Knox dolomite group at 2130 ft. A show of oil was logged in the Knox at 1653 to 1661 ft. Northern Highland Rim.—Three tests widely separated in the Northern Highland Rim were dry.

Jan 1, 1943

By Kendall E. Born

Production of crude oil in Tennessee during 1942 was approximately 8600 bbl., a decrease of 6500 bbl. from the production of 1941, and the lowest since 1934. As usual, the greater part of the production was from the Mississippian limestone pools in Scott and Morgan Counties. Some half dozen wells in Fentress and Clay Counties pumped intermittently produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas respectively. Figures are not available for the Morgan County production but 7,378,000 cu. ft. of natural gas was produced in the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Developments Drilling activities reached the lowest ebb since 1933. Only 10 wells were spudded during the year, one of which was drilling on Dec. 31, 1942. Of the nine completions, two were gas wells in the proven area south of Jamestown in Fentress County and seven were dry holes. The total footage drilled during the year was 14,198 ft.; the average depth of wells was 1578 ft. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 4219 ft., the second deepest well in the state, in Campbell County. The test was in the highly disturbed Valley and Ridge Province, an area long considered the most unfavorable in the state for the accumulation of oil and gas. Cumberland Plateau.-—There were no completions in the Cumberland Plateau area, although an old well drilled deeper found oil from 935 to 965 ft. in the Mississippi lime. This test has created a considerable amount of interest in the area and an active leasing campaign was underway early in 1943. Eastern Highland Rim.—Five completions on the Eastern Highland Rim brought in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area were drilled to the upper part of the Knox dolomite group. The most significant test during the year was the Stanolind Oil and Gas Company's test in Putnam County. This well, on a well-defined surface structure, was abandoned in the upper Knox dolomite group at 2130 ft. A show of oil was logged in the Knox at 1653 to 1661 ft. Northern Highland Rim.—Three tests widely separated in the Northern Highland Rim were dry.

Jan 1, 1943

By Ben E. Lusk

During the past five years, the surface mining industry in Appalachia has launched itself into a technological revolution, which has never been equaled during a similar period of time. Operators have begun to realize that effectively restoring land to a useful purpose, to the satisfaction of all concerned, has to start at the beginning of the operation and be an integrated part of it throughout. In order to insure continued mining in the mountainous areas, with protection of aesthetic beauty, things really have had to change. And so the new steep slope mining theory of "controlled placement" has been developed. Controlled placement is a broad term which means the placement of spoil in steep areas where its condition can be completely stabilized and revegetated. This includes the head of valley fill, mountain top removal, haulback, over the shoulder, block cut, and any other methods where the over-burden is technically delivered, hauled, or compacted, so that there is no adverse after effects when mining has been completed. [(Fig. 1)] Under controlled placement, our whole approach to mining has changed. Before any displacement of soil or uncovering of the coal seam transpires, a complete drainage system

Jan 1, 1977

By H. G. Botset

ANY information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undis-turbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamina-tion by penetration of drilling water, since this problem has been exten-sively studied by other investigators. 1-3 Furthermore, it was regarded as being outside the scope of the present experiments, which were con-cerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essen-tial and obvious procedure is to vary systematically one factor or condi-tion while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program.

Jan 1, 1939

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By Charles B. Dudley

While working, during the summer of 1877, upon the "Chemical composition and Physical Properties of Steel Rails," the results of which are given in my report with this title, I was struck with the surprising wear which some of the rails, which would ordinarily be called soft rails, had endured. At that time I knew of no chemical measure of softness except low carbon, and I found that a numher of rails with low carbon had endured as high or higher tonnage, with apparently as little loss of metal by wear, as those with higher carbon. My own work on steel rails that summer did not embrace any definite experiments as to the amount of metal worn off the rail per million tons which had passed aver it; and so I could get no more definite answer from that work, to the question at the head of this paper, than was given by comparing the appearance of the worn section of the rail with its tonnage. This comparison, however, served to arouse in my mind the query, whether the commonly received opinion as to the relation between the hardness and wearing power of steel is correct, as applied to steel rails. This opinion, if I am right, is: the harder the steel, the better will be the wear, and the limit of hardness is simply one of safety; hard, brittle steel being, of course, more liable to break than soft, tough steel. The query, although aroused, did not bear any immediate fruit, and, as will be evident to any one reading it, the report above referred to was written with the commonly received opinion in mind. Since that time I hare collected a little information upon this subject, which I should be glad to submit to the Institute, if for no other purpose, for the sake of arousing attention, and directing study to the question of hardness versus wear in steel rails. Before making known this information, howevcr, permit me a few words in reference to hardness. How shall we measure the hardness of steel ? Of the various ways of getting indications as to the hardness of steel, which are known, three mill serve our present purpose. These are: 1st. High carbon. It is generally agreed, I think, that at least within proper limits, the greater the amount of combined carbon in a piece of steel, the harder the steel, and I need not do

Jan 1, 1879

By Chas. B. Dudley

WHILE working, during the summer of 1877, upon the "Chemical Composition and Physical Properties of Steel Rails," the results of which are given in my report with this title, I was struck with the surprising wear which some of the rails, which would ordinarily be called soft rails, had endured. At that time I knew of no chemical measure of softness except low carbon, and I found that a number of rails with low carbon had endured as high or higher tonnage, with apparently as little loss of metal by wear, as those with higher carbon. My own work on steel rails that summer did not embrace any definite experiments as to the amount of metal worn off the rail per million tons which had passed over it; and so I could get no more definite answer from that work, to the question at the head of this paper, than was given by comparing the appearance of the worn section of the rail with its tonnage. This comparison, however, served to arouse in my mind the query, whether the commonly received opinion as to the relation between the hardness and wearing power of steel is correct, as applied to steel rails. This opinion, if I am right, is: the harder the steel, the better will be the wear, and the limit of hardness is simply one of safety ; hard, brittle steel being, of course, more liable to break than soft, tough steel. The query, although aroused, did not bear any immediate fruit, and, as will be evident to any one reading it, the report above referred to was written with the commonly received opinion in mind. Since that time I have collected a little information upon this subject, which I should be glad to submit to the Institute, if for no other purpose, for the sake of arousing attention, and directing study to the question of hardness versus wear in steel rails. Before making known this information, however, permit me a few words in reference to hardness. How shall we measure the hardness of steel ? Of the various ways of getting indications as to the hardness of steel, which are known, three will serve our present purpose. These are: 1st. High carbon. It is generally agreed, I think, that at least within proper limits, the greater the amount of combined carbon in a piece of steel, the harder the steel, and I need not do

Jan 1, 1879

By R. Taggart, R. H. Ericksen, D. H. Polonis

MarTENSITIC a has been observed to form spontaneously from the retained ß phase during the preparation of thin foil specimens of metastable Ti-Cr alloys containing from 6.9 to 20 wt pet Cr. Similar spontaneous martensite reactions have been reported in thin foils of 0 brass' and other alloys.2 4 The absence of retained austenite in iron-based alloys has also been attributed to spontaneous decomposition during thinning.5 The present work indicates that a unique situation occurs during which the spontaneous transformation takes place when the transitional ? phase is present in the as-quenched or partially aged ß phase. Alloys containing 6.9, 7.0, 8.0, 12.0, and 20.0 wt pet Cr were prepared by the levitation melting of "io-chrome" chromium and iodide titanium. The 0.5-in.-diam ingots were vacuum-annealed at 1000oC, and wafers 0.020 in. thick were then cut from the ingots. These wafers were wrapped in molybdenum foil, encapsulated in Vycor under a reduced pressure of purified helium, and then held for 30 min at 1000°C. The specimens were quenched in water to retain the metastable high-temperature ß phase. The quenched alloys were thinned by mechanical grinding to about 0.005 in. thick, then electropolished in a solution of 300 ml methyl alcohol, 175 ml n-butyl alcohol, and 30 ml perchloric acid at a temperature of -40°C. Needle specimens 0.005 to 0.010 in. diam were taken from each ingot and heat-treated with the foil specimens. X-ray diffraction patterns indicated the structure of the 6.9, 7.0, and 8 wt pet alloys to be a

Jan 1, 1968

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, 'however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel ' 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650' C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941