Search Documents

By Valentin Garfias

ALTHOUGH Mexico still ranks second in importance as produce for petroleum, the output in 1924 was 7 ½ per cent. less than in 1923 and 30 per cent. less than the peak production of 1921. The decrease may be partly accounted for by labor troubles and revolutionary activities early in the year, although undoubtedly the main factor was the continuous rise of the salt-water level in the South Fields, causing a decline of 24,000,000 bbl. in the production of light oil. Since the middle of 1923, the production of heavy crude has been greater than that of the lighter grade and, in 1924, the output of heavy crude was 2 ½ times that-of the light oil. DEVELOPMENT Drilling operations in the Mexican fields were probably more active in 1924 than in any other year, the greatest activity taking place in the Cacalilao and neighboring fields; toward the end of the year there was an added number of wells drilling in wildcat areas. The number of wells drilled in proved territory was almost twice that of the previous year, the increase taking place in the heavy-oil fields north of Panuco, as only 78 of the 710 wells completed were drilled in the Southern Fields. The percentage of successful completions decreased from 45 per cent., during 1923, to about 38 per cent., during 1924; there was also a noticeable decrease in the average flush production of the new wells. It is interesting to note that notwithstanding the increased drilling activity, the total production declined over 10,000,000 barrels. In the heavy-oil district, 632 wells were completed but only 231, or 36 ½ per cent., were commercially productive. The develop-ment in the Cacalilao area reached its peak in April and May, or about the time the first serious salt-water encroachments took place. Development in the old Panuco and Topila fields was more active than during the previous year, although the salt-water level continued to rise, the high price of crude making such development advisable especially for companies having to protect large-investments.

Jan 3, 1925

By M. R. Tek

A new method for correlating the data on multiphase flow through vertical pipe is presented. The correlation is based on a "two-phase f factor" concept which was developed and successfully applied to horizontal multiphase flow by Bertuzzi, Tek and Poettmann. Field data previously published on several flowing and gas-lift wells have been used as the basis for the developed correlation. The application of the method to actual two-phase flow problems indicate that this method is capable of predicting the pressure distribution in vertical multiphase flow strings well within the accuracy range usually desired for common engineering and design calculations. A new working chart developed for calculation of two-phase pressure gradients and a graphical step-by-step procedure for the computation of pressure distribution are presented along with an example problem. INTRODUCTION Multiphase flow through vertical pipe is encountered in many engineering installations. In petroleum, chemical process, nuclear engineering and many other industries, problems associated with simultaneous flow of two or more phases through vertical pipe have been of interest for a long time. This interest has increased considerably during recent years due to applications to new processes in petroleum production and refining and to problems of steam generation and heat removal from nuclear reactors. One prominent example of vertical two-phase flow is provided by the gas-lift process where oil, water and gas flow simultaneously. If the pressure profile in a gas-lift well can be predicted within reasonable accuracy, it would be possible to get good estimates of the power required to lift the oil, the optimum depth, the pressure and the rate at which to inject gas. Furthermore, the effect of production rate and tubing sizes on these quantities can be evaluated before any design decision is made on the installation and operation of the flow string. The majority of experimental work available in the literature deals with two-component systems where individual phase flow rates in and out of the pipe remain constant. The general problem of prediction of pressure drops in multiphase flow systems is very complicated. The co-existence of numerous flow patterns of widely different geometry and mechanism, conditions of surface instability and the nature of force fields acting upon the system are among the major difficulties commonly encountered. The classical approach of fluid dynamics which would be based upon the formulation and solution of Navier-Stokes equations has been found by many investigators completely devoid of any hope of success-—not only because of inherent nonlinearities but also because of insurmountable analytical difficulties standirng in the way of setting up the boundary conditions. The presence and effect of interfacial forces on mu1tiphase flow systems further complicate the theoretical approach. For these reasons, many investigators choose to adopt semi-empirical if not purely empirical approaches in order to obtain solutions of engineering utility. A prominent practical solution has been given by Poettmann and Carpenter' in the form of an empirical correlation. In their paper, total flowing densities of fluids and solubility effects of gas in oil have been taken into account for the correlation of field data covering a wide range of operating conditions for oil wells. They treated the gas. oil and water as a single phase of combined propcrties and correlated the multiphase friction factor as a function of the product (pvd), i.e., density X velocity X diameter of the flow string. However, because the product (pvd) is dimensional while the frictior factor is dimensionless, the generality of their result's is somewhat restricted. It seems that the omission 01 viscosity effect may be one of the reasons for the scatter of data as shown in their correlation chart. The concepts of the "two-phase f factor" and the "two-phase Reynolds' number function" were recently developed and successfully applied to correlate horizontal multphase flow by Bertuzzi, Tek and Poettmann.' Recently, two new methods of correlation by Tek and Chan' have been presented on simultaneous flow of liquid and gas through vertical pipe. These two methods of correlation and the working equations in field units necessary for their application are included in this paper. The extension of the conccpt of two-phasc Reynolds' number function successfully developed for horizontal flow into vertical multiphase flow systems, development and evaluation of working charts permitting calculation of two-phase pressure gradients and

By K. F. Veith, R. L. Marovelli, T. S. Chen

An analytical study is made of thermal stress distribution in a thin circular disc subjected to a peripheral thermal shock at various rates of heat transfer. The problem is of importance in predicting the thermal shock response of a rock body of finite size. The theoretical analysis is based on radial heat flow by conduction in the disc and heat exchange by convection between the disc and the surroundings. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks and an average stress theory is formulated. Preliminary experimental verification was obtained from the results of shock tests on thin rock discs insulated on both flat end faces so that heat exchange took place through the exposed peripheral surface. Physical properties vital to the analysis are Young's modulus, tensile strength, coefficient of linear thermal expansion, thermal diffusivity and thermal conductivity. Plots of these properties are presented. Historically, thermal energy has been used for primary rock removal throughout the ages. Although it is not widely known, the fire-setting method of thermal rock fragmentation was still in use 100 years ago in systematic underground mining operations in Scandinavia.' There, the availability of cheap labor and abundant wood fuel made the method competitive with the early blasting powders. By 1880, as high explosives replaced powder, use of the method declined and it was finally abandoned about 1885. Only 40 years ago, some experimental fire-setting methods were used for rock removal underground at Pribram and Zinnwald in Central Europe.2 Compressed air-oil burners replaced the earlier wood fuels. About 15 years ago, gaseous oxygen-oil burners were introduced in the United States and gained acceptance for difficult blasthole drilling and some quarry opera- tions. At present, there is renewed interest in the compressed air-oil burner designs. The literature included information on thermal secondary processes for rock weakening or particle liberation3,4,5,6,7,8 on thermal spallation of rock 9,10,11,12,13 and on the thermal fracture of materials other than rock. The 1955 Symposium on Thermal Fracture14 and the later work of Hassel-man, cover recent developments in thermal shock investigations on brittle ceramics. Although the number of published analytical and experimental investigations conducted on ceramic and refractory materials is large, the literature reveals that there is a lack of information on both the theoretical and actual response of rock to thermal shock. Many of the thermal shock studies on ceramic and refractory bodies are based on the case of heat transfer at the solid's surface by convection in either liquid or air. A similar heat transfer situation was adopted for a theoretical analysis of the thermal stresses in a thin circular disc subjected to a peripheral thermal shock. Experimental thermal shock tests were then conducted on rock specimens to check the analytical results. Specially insulated quartzite, basalt and taconite discs were shocked in either liquid or still air bath at various rates of heat transfer. The work was done in order to resolve the question as to whether theoretically determined tensile stresses are actually realized in a finite rock body undergoing thermal shock. Specifically, if theory predicts that the tensile strength of a rock should be exceeded in a particular type of controlled thermal shock, will fracture occur? This information is needed by Bureau researchers working on thermal and electrical rock fragmentation methods. The object of this paper is to present the main features of the theory and procedure being used in the authors' approach to quantitative prediction of rock response to a thermal shock. THEORETICAL ANALYSIS In the analysis to follow, simple geometry of a thin circular disc is considered. The disc is assumed to be isotropic, homogeneous and perfectly elastic, and to have constant thermal and mechanical properties. The effect of radiation is neglected so that heat is transferred by conduction inside the disc and by convection with its surrounding. In addition, the end

Jan 1, 1967

By J. Weertman

It is shown that conditions suitable for the conversion of straight dislocations into helices are common in crystals hardened either through long-range dislocation interaction or by jog formation on dislocation lines. For dislocations other than screw dislocations or dislocations nearly screw in orientation, helices can be formed with the aid of core difhsion at temperatures low relative to the melting point of the material. It is assumed that, once formed, helices will degenerate into dislocation tangles. THE dislocation tangle is one major dislocation arrangement observed by the transmission electron microscope which had not been predicted previously from dislocation theory. Since first being observed, the tangle itself has become important in applied dislocation theory. The Cambridge school (P. Hirsch) bases part of its theory of work hardening upon this phenomenon.' In spite of the fact that the tangle obviously is a structure of prime importance to a cold-worked crystal, until recently relatively little attention has been paid to the question of exactly why or how tangles arise. It was generally assumed at first that cross slip and perhaps jog formation will lead to tangles. However Wilsdorf and schmitz2 concluded that cross slip cannot markedly contribute to the tangles. The Wilsdorfs and Maddin3'* have proposed that tangles arise by means of prismatic dislocation loops and superjogs which are produced by a precipitation of point defects. Dislocations with superjogs or which have joined with prismatic loops are themselves dislocation sources and they can produce new dislocations, a process they call "mushrooming", which then tangle with each other. There is no question that the Wilsdorfs et al. mechanism as well as the cross slip one can pro- duce tangles. However these may not be the only paths leading to tangle formation. In this paper we wish to consider another way tangles can form. Our work will be based on the theory of dislocation screw We wish to show that whenever a crystal is cold-worked there always is present a "driving force" leading to helix formation and thus to tangle formation. We do not expect to observe well-developed, regular helices in cold-worked metals. Rather we would expect that after a helix is formed random interactions with nearby dislocations will cause a well-developed helical dislocation to go over into an irregular form. A dislocation tangle is, of course, a grouping of dislocations with irregular forms. Therefore we feel that, in accounting for the formation of dislocation tangles, it is sufficient to show that many dislocations in a cold-worked crystal will take on helical form. The crucial step is helix formation. In order to have a straight dislocation assume a helical form, diffusion of vacancies, or interstitials, must occur. Our discussion of tangle formation therefore will be limited to crystals which have been deformed at temperatures ranging from about one fifth to half their absolute melting point. In this tem per a ture range appreciable core diffusion is possible. (There is no problem in explaining tangle formation at temperatures greater than half the melting point. At such temperatures dislocation climb through a bulk diffusion of point defects gives an extra degree of freedom to dislocation motion. This extra freedom of motion makes tangle formation easy.) At temperatures much below one fifth the absolute melting temperature diffusion processes are sufficiently slow that helix formation does not occur. Of course helix or tangle formation could occur in material deformed at very low tempera-tures which was subsequently warmed in order to make the thin specimen necessary for electron-microscope examination. Since within the temperature range of approximately one fifth to half the melting temperature the diffusion of point defects in the core of the dislocation is rapid, we can reasonably assume that within

Jan 1, 1963

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, yet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 99.9 per cent saturated at each temperature. The specimen was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully carburized specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Frank W. Clinard, Oleg D. Sherby

The effect of multiple an transformations on diffusion in a dilute iron alloy was studied. Inter-penetration between iron and an Fe-Co alloy was evaluated, under thermal-cycling conditions chosen so as to transform only the iron-rich side of the diffusion couple. It is shown that a small but consistent diffusion enhancement by a factor of two results when data from the transforming side of thermally cycled specimens are compared with predicted inter diffusion coefficients based on isothermal data. No enhancement is found when data from the mntransforming side of such couples are compared with predicted diffusivities. It is suggested that short-circuiting by moving pain boundaries is the most likely mechanism contributing to the observed diffusion enhancement from multiple phase transJormations in iron. Transformation-induced Point defects, dislocation-pifie short-circuiting, and point defects generated by dislocation motion are less effective in contributing to enhanced diffusion under the experimental conditions utilized. SO far as is known, no studies have been made of the effect of allotropic transformation on diffusion. previous to this investigation. Studies have been made, however, of the influence of transformation on the diffusion-controlled processes of spheroidization and sintering. Cullen1 has described a method of accelerating spheroidization in an AISI 1030 steel. Partial transformation between a and ? phases was uti-

Jan 1, 1965

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

By H. W. McCue

In 1944, in the Texas Panhandle, 245 oil wells were drilled with a total daily initial production of 32,886 bbl., representing an average initial production of 134 bbl, per well. This was an increase over 1943 of 121 wells drilled, and an increased initial production of 13,861 barrels. On Dec. 31, 1944, the field was operating on an allowable of 113,567 bbl. per day, but actually was producing 85,539 bbl. per day from the 5901 oil wells. The tota1 production for the year was 33,439,436 bbl., bringing the cumulative total to 5.04,537,048 barrels. Gas Sixty-three gas wells with a combined open flow of 992 million cu. ft., were drilled during 1944. This was an increase of seven wells over 1943, but a drop of 216 million cu. ft. in initial open flow. The

Jan 1, 1945

By Kendall E. Born

Production of crude oil in Tennessee during 1944 was slightly more than 9500 bbl., about 1300 bbl. more than 1943. Approximately 8000 bbl. was produced from the "Mississippi lime" in Scott and Morgan Counties. Some half dozen wells in Clay, Pickett, and Fentress Counties, pumped intermittently, produced about 1500 bbl. This production is from rocks of Ordovician age ranging in depth from less than 500 ft. to approximately 1000 ft. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production of oil by counties is shown in Table I. Developments There were 20 completions during 1944 totaling 19,615 ft., nearly twice as much as in 1943. One well was drilling on Dec. 31, 1944. Of the 20 completions, one was a small oil well soon abandoned. Three gas wells were completed which are used locally. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Plateau There were five completions in the northern part of Cumberland Plateau. One was a small gas well in the Cooper pool 3 miles west of Oneida, but an attempt to extend the pool to the south resulted in a dry hole. The most active area in the state during 1944 was the northern Cumherland Plateau, especially in Cumberland, Morgan, and Scott Counties. Several blocks, aggregating more than 500,000 acres, were assembled and leasing was continuing in the early part of 1945. Surface work has been, or is being, carried on by at least four companies. While in an area of past oil and gas production from the "Mississippi lime," the principal interest appears to be in the essentially unexplored pre-Mississippian possibilities. The Knox dolomite group of Cambro-Ordovician age is receiving some attention as a possible reservoir. As the year closed one well was drilling on a surface structure near Lantana, 6 miles southwest of Cross-ville. This test will be drilled into the upper part of the Knox. Late in 1944, it was planned to lay a gas line from northern Morgan County to Oneida in Scott County, a distance of approximately 20 miles. Middle Tennessee Fifteen wells were drilled in Middle Tennessee. In the northeastern Highland Rim area there were 11 completions, one

Jan 1, 1945

By A. M. Gaudin

The flotation process has been applied extensively in the mineral and chemical fields. This paper reveals results obtained by an exploration of an application to the biological field. In many ways this study was indeed an exploration since so many factors are different. In the mineral field, the particles, both those floated and those not floated, cover a wide range of sizes and shapes; in the biological field, the particles of one population are primarily of one or two sizes and one or two shapes. This identity in size and in shape gives biological systems the advantage of homogeneity. In the mineral field the particles may be as coarse as a millimeter; in the biological field the size may be a micron, or less. In the mineral field the particles may have a gravity several times that of water so that their apparent gravity is quite substantial. Microorganisms, on the other hand, may have a gravity so near that of the liquor that their settling velocity in the liquor is vanishingly small. These two facts conspire to make bubble-particle encounter in the pulp-body less likely. Finally, microorganisms are living, reproducing, and dying-all of which does not help the experimenter get a balance of materials. The analytical problems, too, are extraordinarily difficult, for the organisms can contain only elements that occur in their environment, although at a different level of concentration. The chemical composition of the surface of microorganisms is readily altered. In spite of these areas of difficulty, microorganisms can be floated to leave practically water-clear tailing, they can be floated from each other and, in fact, the same organism can be fractionated into a float that differs from the sink. SIZES AND SHAPES OF ORGANISMS Most ore pulps are described with reference to the percentage of the pulp that is fine enough to pass a 200-mesh sieve. Thus a copper-ore pulp may be 80% -200 mesh. Since 200 mesh equals 74 µ, a 2000-mesh particle would be 7.4 µ in diameter, and a 20,000-mesh particle would be 0.74 µ. The microorganisms with which this work is concerned are of the order of magnitude of 20,000 mesh. We have worked with Escherichia coli, the colon bacillus, Bacillus cereus, Bacillus subtilis, Bacillus megaterium, and Serratia marcescens. In some pioneer work, Dognonl,2 reported the use

Jan 1, 1962

By B. C. Mariacher, I. Hoffman

In 1952, beneficiated phosphate ore first began to move from the Oron plant of Negev Phosphates Ltd. in the Negev Desert to the super-phosphate plant at Haifa, Israel. Since that time this company has continually sought to overcome its natural handicaps affecting the operating efficiency and quality of the product in an effort to bolster the agricultural program of Israel and the development of an exportable commodity. The most serious deterrent to the development of a beneficiation process was the total absence of water. The Oron plant lies approximately 30 miles south of the irrigated regions of Israel with the nearest producing water well located about 10 miles to the northwest. The urgency of early phosphate production made it necessary to consider only dry processes in the initial operation. Fortunately, the ore was amenable to a dry process which yielded a usable concentrate assaying about 28.5 pct P2O5; but phosphate recovery was low. A description of the characteristics of the Negev ore should help to clarify the principles upon which the dry concentration is based.

Jan 5, 1961

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1939. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns.

Jan 1, 1941

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1939. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns.

Jan 1, 1943

By A. L. Marshall, F. J Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944