Search Documents

By A. W. McReynolds

E. OROWAN*—I observed the phenomenon of jerky yielding many years ago with zinc25 and cadmium single crystals. A significant point was that the jerks occurred not only when the stress was raised but also (sometimes, after a pause of many minutes during which no trace of creep was observable) at constant stress. The phenomenon may be closely linked with the inertia of the testing machine and of the specimen, although the inertia alone cannot account for it. If, during the test, the resistance of the material to plastic deformation suddenly diminishes while the applied force remains constant, a sudden deformation follows until the yield stress has risen, by strain hardening, to the level of the applied stress (= the value of the previous "upper yield point."). When this is reached, the rate of deformation has attained a maximum value because, up to this moment, the applied force was higher than the plastic resistance of the specimen, and the difference was used for accelerating the moving parts of machine and specimen. The kinetic energy accumulated is now transformed into plastic work by further deformation; that is. the deformation overshoots the point at which the plastic resistance equals the applied static force. When the kinetic energy has been used up, therefore, we are left with a specimen the yield stress of which is higher than the applied stress, and no further deformation can occur (apart from a little creep) until either the applied stress has been raised to the new yield stress level, or the yield stress has fallen by thermal recovery to the level of the applied stress. While this occurs, a new upper yield point can develop, for example, by precipitation.26

Jan 1, 1950

September 1 to 6, 1918 COMMITTEE IN CHARGE Spencer Penrose, Chairman. George M. Taylor, Vice-Chairman. A. E. Carlton, Chairman. Finance Committee J. Dawson Hawkins, Secretary DENVER COLORADO SPRINGS CRIPPLE CREEK Finance Finance Thomas B. Crowe T. B. Stearns A. E. Canton , E. P. Arthur, Jr. Richard A. Parker Spencer Penrose N. S. Greensfelder T. B. Burbridge George M. Taylor A. E. Carlton. A. L. Blomfield, Treasurer B. F. Hill Arrangement I F. G. Willis Dave G. Miller Registration Norris E. Eads Frank Bulkley Loren C. Lennox 1V. E. Ryan Geo. E. Collins Horace F. Lunt Fred Jones .1. M. Tippett F. D. Smale Entertainment J. H. Haynes F. H. Bostwick Arrangement and Entertainment L. W. Lennox F. E. Shepard George M. Taylor A. L. Blomfield M. R.. Valentine Howland Bancroft J. D. Hawkins Thomas B. Crowe B. P. Morse A. E. Carlton E. P. Arthur J. G. Perry G. H. Clevenger Etienne A. Ritter Ladies Ladies , PUEBLO Mrs. T. B. Stearns, Mrs. C. M. Taylor, Mrs. C. H. Clevenger J. F. Welborn Chairman. Chairman H. B. Carpenter Mrs. C. Loughridge Mrs. S.-Penrose Mrs. A. E. Carlton L. B. Eames Mrs. H. Bancroft Mrs. J. D. Hawkins Mrs. A. L. Blomfield F. Robinson Mrs. G. Bancroft Mrs. L. C. Lennox Mrs. J. M. Tippett . Mrs. W. D. Leonard Mrs. H. F. Lunt -Mrs. E. C. van Diest Mrs. C. Chase Mrs. E. A. Ritter Mrs. AV. Strieby Mrs. F. H. Bostwick Mrs. L. S. Harner Mrs. C. L. Bailey Mrs. F. Bulkley Miss F. Dickerman Mrs. E. P. Shove Mrs. C. L. Tutt Mrs. F. C. Peck Mrs. F. D. Pastorius

Jan 10, 1918

By ROBERT H. BOOTH

THE happy intra-plant relationships of the Bridgeport Brass Co. are largely attributable to the interest of the management in this important business factor. In furtherance of this development Carl F. Dietz, President of the Company and a member of the Institute, has contributed the novel plan for the objective presentation of business economics, described herein. All of the officers of the corporation are active in its management and they together with many other workers filling both executive and subordinate positions have a substantial financial interest in the enterprise. The viewpoint of this organization is fairly reflected by the following quotation from Roosevelt's "The Foes of Our Own Household."

Jan 1, 1924

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull's suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin's observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin's studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several ' strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r' phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By A. G. Guy

IN the course of a research on steady-state diffusion it became necessary to make diffusion calculations for a finite solid. This problem was found to be sufficiently different from the corresponding problem for the semi-infinite solid for an entirely new approach to be necessary in obtaining a useful solution. The assumption of an exponential variation of the diffusion coefficient with concentration' was no longer a practical necessity, so that the new solution offered the possibility of handling diffusion in semi-infinite solids for arbitrary variations of the diffusion coefficient with concentration. In discussing the principle on which this method of calculation is based, it is convenient to consider the relatively simple problem of one dimensional diffusion into a matrix that initially contains none of the diffusing substance. The solution of the set- ond Fick Law,?C/?t=D0?2C/?x2, for diffusion into a semi-infinite solid is3 C/C=1-F(x/2vD0t [1] where C is the concentration of the diffusing substance at a depth x cm below the surface after dif- A. G. GUY, Member AIME, and M. GOLOMB are Professor of Metollurgicol Engineering and Professor of Mathematics, respectively, Purdue University, Lafayette, Ind., A. S. YUE, formerly with Purdue University, is now with the Research Laboratory, Dow Chemical Co., Midland, Mich. TP 4505E. Manuscript, July 18,1956. fusion has occurred for t seconds; C, is the concentration of the diffusing substance at the surface of the matrix; Do is the diffusion constant, expressed in sq cm per sec; and + represents the Gauss error function. The corresponding solution for diffusion into a finite solid of thickness, 1, is conveniently written for the change in concentration, C+, at a point midway through the matrix and for times, t, great enough for the following equation to be used4 c1/2/C1=(1/2-2/?e-?2D0t/l2) [2] In Eqs. 1 and 2 the diffusion coefficient is represented by the symbol Do (rather than by D) to emphasize that these equations are valid only for constant values of D. To understand how these equations can be modified to take account of actual variations of D, such as that shown in Fig. 1, first consider the fact that for a given time of diffusion theconcentration at a given point is determined, not by the D value alone, but by the ratio x/vD0 in Eq. 1 and by a similar ratio, l2/D0 in Eq. 2. Even though in fact D varies, it is possible to keep this ratio constant by using a special coordinate system, x,, that varies with D in the appropriate manner. The necessary character of this special coordinate system can be easily visualized by imagining that

Jan 1, 1958

By GEO H. DEIKE

NOT much activity has been evident during the past year in the establishment of co-operative scholarships but the interest among the coal-mining companies is more pronounced than ever. This is apparent from the replies received to a letter sent out by the Committee on the Promotion of Student Interest in Coal Mining to over 120 coalmine operating officials. With that letter was forwarded a bulletin issued by the school of mineral industries of The Pennsylvania State College entitled ?Industrial Scholarships ? a Partnership of Industry and Education.? In that circular was outlined the need for trained men in the war and postwar world, and particularly as such demands pertain to the growth of the mineral industries.

Jan 1, 1943

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable ' any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By C. M. White

CITIZENSHIP is a rather abstract subject on which a great deal could be said-a subject on which a great deal is said -and still one which too many of us seldom think about and seldom work at. Too many of us engineers and business men have but a vague idea of citizenship. We think that if we go to the polls on election day and obey the laws scrupulously, with the exception of an occasional traffic violation, we are pretty good citizens and are doing our duty by our city, state, and nation. But when you think it over, that's a very passive observance of the important right of counting oneself a citizen of a country. There is nothing very positive in that attitude. There is nothing that indicates that we have sufficient interest to really go out and do a job for the -welfare of our country, forgetting any personal advantages or inconveniences that might arise. In other words, this type of voting-on-election- day, law-abiding citizenship does not keep us awake a single minute; it does not take any particular thought or require the expenditure of any time or energy.

Jan 1, 1939

By William F. List, Marvin A. Schuster

Monolithic electrooptical mosaics of 2500 photo-transistor elements with internal row and surface column interconnections have been fabricated by epitaxial-planar diffsion techniques. Unique access to any elemed of the mosaic is provided through one of the fifty X and one of the fifty Y external leads. The sensor mosaic can be used for imaging applications and has a 1:1 aspect ratio, a resolution of 100 lines per in., a dynamic range in excess of lo3, a sensitivity of 0.5 per pw, element response within a 2:l range over 75 pct of the mosaic, and a minimum detectable signal of the order of 10-' w. Design considerations which ilnpose particclar fabrication yequirements are disctussed along with some of the problems peculiar to the epitaxial and planar-dijfision techniqes by which this device is fabricated. The solid-state silicon monolith has an imaging area of 0.5 by 0.5 in. and an element center -to- center spacing of 0.010 in. J monolithic solid-state electrooptical device has been developed as the photon-sensing mosaic for use in an image-converter system.' This system is the solid-state equivalent of the vidicon and can image radiation in the visible and near-infrared regions of the spectrum. The electrooptical image converter has the desirable size, weight, reliability, and low-power characteristics inherent in solid-state devices. It is read out by direct-wire means rather than by beam-scan techniques. The packaged unit is shown in Fig. 1. A selection of material for the sensor was based on considerations of both reliable fabrication techniques and material spectral response. Silicon was selected both for its response from the lower end of :he visible to the long-wavelength cut-off above 11,000A and for its well-developed epitaxial planar-diffused technology. The electrical image is composed of M x N discrete information bits with each bit emanating from one of the individual phototransistor sensors. The interconnected mosaic concept was introduced to provide a structure which is both manageable in its number of leads and compatible with conventional viewing systems which accept XY data. Interconnections along the Y direction are provided by internally diffused strips, while interconnections along the X direction are formed by vacuum-deposited metal surface bars. Unique access to any individual element of the M x N mosaic is available through one of the M and one of the N external leads. PHOTOTRANSISTOR DESIGN A phototransistor structure2 was selected for the discrete photon detectors of which the mosaic is com- posed. Basically, the mode of phototransistor operation is such that incident quanta are absorbed in the base area of the element where they generate electron-hole pairs. If the electrons are liberated within a diffusion length of the depletion region around the collector junction, they will diffuse to this depletion region and be swept across the junction where they account for a small component of the photocurrent. Similarly, the holes which are created within a diffusion length of the emitter junction will diffuse to this region where they forward bias the emitter and so induce injection of minority carriers into the base. This accounts for the substantial transistor photocurrent. This mechanism of operation implies several design and fabrication goals for the individual sensor elements: high electrooptical conversion efficiency, sufficient carrier lifetime in the base regions, and a maximum volume in which photons can be absorbed within a diffusion length from the depletion layer about the junction. Moderately high transistor gain is desirable to permit readout at low light levels; however, very high gain has a deleterious effect on mosaic dynamic range. The mosaic must also be characterized by good uniformity of element response as well as by good isolation between elements. The above set of conditions imply that junction depths must be optimized with respect to photon ab-

Jan 1, 1967

Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the metallurgy, fabrication and uses of the nonferrous metals and their alloys; to represent the A. I. M. E. in so far as nonferrous metallurgy is concerned, within the rights given in A. I. M. E. By-law XI., Sec. 1, and not inconsistent with the Constitution and By-laws of the A. I. M. E.; to hold meetings for social intercourse and the discussion of nonferrous metallurgy; to stimulate the writing, presentation and discussion of papers of high quality on nonferrous metallurgy; to reject or accept such papers for presentation before meetings of the Division. Article II—MembeRs Sec. 1. Any Member, Associate, or Junior Associate of the A. I. M. E. in good standing may become a Member, Associate or Junior Associate of this Division upon registering in writing a desire so to do, but without additional dues. Sec. 2. But no one who has been continuously indebted to the A. I. M. E. or to this Division for more than three months shall be entitled to vote or to receive publications to which, as a member of the Division, he would be entitled. Article III—Funds Sec. 1. The expenditure of the funds reccived by the Division shall be authorized by the Executive Committee of the Division. Article IV—Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the A. I. M. E., and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the A. I. M. E. Sec. 2. The annual business meeting for election of officers shall be held within a few days before or after the annual business meeting of the A. I. M. E. Sec. 3. At any meeting of the Division for which notice has been sent to the members of the Division through the regular mail at least one month in advance, a business meeting may be convened by order of the Executive Committee, and any routine business transacted not inconsistent with these By-laws or with the Constitution or By-laws of the A. I. M. E. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. Article V—Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, two Vice-chairInen, Secretary and Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, in so far as is consistent with the By-laws of the Division and the Constitution and By-laws of the A. I. M. E. Institute of Metals Divisiori

Jan 1, 1931

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By F. Robertson Jones

IF the tendency toward extending the scope of the workmen's compensation system to include life, health, accident, old age, and unemployment insurance for workers is not promptly altered, I believe there will be a complete breakdown of that system. This is not because of any objections, there may he to requiring industries to provide these additional forms of protection in whole or in part to their employees. It is rather because our workmen's compensation laws, their scale of benefits, and the administrative procedure under them are not adapted or suited to such situations. If the compensation principle is limited to its own proper sphere and is not enlarged so as to include all the ills that the flesh is heir to, it is practical, "workable, and beneficent. If it invades foreign realms, it is bound to grow into a veritable Frankenstein' which will harm principally those it 'is supposed to aid, and, at the same time, will promote waste, fraud, and Industrial demoralization. Compensation risks will become almost uninsurable; the cost to business will be intolerable; and the development of sound relief measures which will give to labor the protection now sought by the uneconomic device of enlarging the compensation law territory will be retarded.

Jan 1, 1934

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964