Search Documents

By B. H. Sage, W. N. Lacey, W. M. Morris

The volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrelll measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0 to 130 F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70" to 250" F. The specific volume in the gas and liquid region was determined at pressures up to 3000 Ib. per sq. in.? throughout this temperature interval. In addition, the vapor pressures were measured at 30" intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0" and 250" F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100" and 460" F. was carried out with apparatus that has been described in another paper (p. 136, this volume). Materials The isobutane used in this investigation was obtained from the Philgas Division of the Phillips Petroleum Co. That company's special analysis upon this sample indicated it to contain less than 0.03 mol per cent of impurities. In order to avoid traces of noncondensable gases, this hydrocarbon material was subjected to two successive fractionations at a high reflux ratio in a column approximately 4 ft. long and % in. in diameter, which was packed with small glass rings. The middle portion of distillate from the first fractionation was used in the second fraction-ation and a portion of the overhead from this second distillation process was repeatedly condensed at liquid-air temperatures at a pressure only slightly above the sublimation pressure of isobutane at this temperature.

Jan 1, 1940

By W. N. Lacey, B. H. Sage, W. M. Morris

The volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrelll measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0 to 130 F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70" to 250" F. The specific volume in the gas and liquid region was determined at pressures up to 3000 Ib. per sq. in.? throughout this temperature interval. In addition, the vapor pressures were measured at 30" intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0" and 250" F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100" and 460" F. was carried out with apparatus that has been described in another paper (p. 136, this volume). Materials The isobutane used in this investigation was obtained from the Philgas Division of the Phillips Petroleum Co. That company's special analysis upon this sample indicated it to contain less than 0.03 mol per cent of impurities. In order to avoid traces of noncondensable gases, this hydrocarbon material was subjected to two successive fractionations at a high reflux ratio in a column approximately 4 ft. long and % in. in diameter, which was packed with small glass rings. The middle portion of distillate from the first fractionation was used in the second fraction-ation and a portion of the overhead from this second distillation process was repeatedly condensed at liquid-air temperatures at a pressure only slightly above the sublimation pressure of isobutane at this temperature.

Jan 1, 1940

By R. W. Raymond

[NOTE.-This paper was presented at the Pittsburgh meeting in a partially completed form, and I fully expected to obtain, before the period of its publication, both the data and the leisure required for its completion. The hygiene of collieries was to have been separately considered, and the sanitary conditions of various metallurgical industries connected with mining were to receive an extended discussion, while at the same time the points treated in the paper as presented at Pittsburgh were to have more ample illustration from American and European sources. Delay in obtaining expected information, and the continuous pressure of professional work, have prevented hitherto the execution of this plan ; and I can now publish only a portion of what I had designed to contribute to the subject. In the meantime this portion, but slightly changed, has been included as a chapter on the Hygiene of Metal Mines in a work entitled Hygiene and Public Health, edited by Dr. A. H. Buck, of New York. An excellent chapter on the Hygiene of Coal Mines, contributed to the same work by Mr. Henry C. Sheafer, of Pottsville, affords me an opportunity to supply one of the deficiencies above alluded to. Mr. Sheafer's chapter contains much material in the way of explanations not required by professional readers; and he moreover devotes a considerable space to the explosive gases, falls of roof, and other causes of accidents to life or limb-a branch of the subject not belonging strictly to hygiene. I therefore make extracts only from his treatise.-R. W. R] IT is convenient to divide mines, with reference to this subject, into two classes, collieries and metal-mines. Subterranean quarries, rock-salt mines, etc., present no conditions requiring them to be separated from the latter class.

Jan 1, 1880

By W. R. Finlay, W. R. Jr. Hibbard

The key feature of the lattice coherency theory of precipitation hardening1 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.6'6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: rz pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pet copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,~ studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkins~n,~ in 1944, applied tensile creep stresses to a complex copper. nickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1949

FREQUENTLY the careful engineer puts the word porphyry in quotation marks or precedes it with "so-called," when he writes of the Porphyry Copper mines. This is done by way of serving notice that he is aware that the term is not a precise one, though no one who is informed on the subject would in any event misinterpret it. The name originated from the fact that the rock containing the copper at Utah Copper, Morenci, Nevada Consolidated, and Braden-the first four to be developed-was in each instance known as porphyry. The term was convenient; and when Ray, Miami, and inspiration came along they fell into the Porphyry category even though the ore consisted essentially of a rock called schist instead of porphyry. The word is not inclusive enough; nor as a matter of fact is it sufficiently exclusive. Numerous copper deposits occur in porphyry rocks that are not Porphyry Coppers, paradoxical as it may seem. Desiring to be more accurate and at the same time to use a word that is in some degree descriptive, various engineers have adopted the expression "disseminated copper deposits." This alludes to the characteristic scattering of grains or specks of copper minerals more or less uniformly throughout the mass of the rock. Yet here again the implication is not entirely accurate, for the following reason: in some of the ores, the proportion of copper minerals "peppered" in the rock is small, compared with that which coats the walls of cracks and minute fissures; and that which is found as veinlets along planes of fracture. Many geologists have extended their interpretation of the term disseminated to include both types of mineral occurrence. One of the most striking features of the Porphyry ores is the intense shattering and fracturing that the rock underwent at some period or periods prior to the deposition of the copper

Jan 1, 1933

By Richard P. Rothwell

The device to which I desire to call the attention of the members of the Institute consists of a water-tight caisson, which is connected By a stuffing-box with the tube to be laid, and the caisson is pushed forward with hydraulic jacks set against the end of the tube. The tube is of hard white iron, cast in chills in segments. These segments are carried from shore through the tube itself, in which a track is laid as the work progresses, and the segments are bolted together in the caisson, where there is ample room to work and proper appliances for handling heavy weights. As each segment is bolted on, the jacks are set against its forward end, and when the whole ring is complete, the caisson is pushed forward by the jacks, a trench having been dredged out in front of it, or, in very loose ground, jets of water under a heavy pressure can be thrown out to loosen the ground in front of the caisson. The direction in which the caisson is pushed is completely under control, and both the caisson and the tube are loaded to the amount necessary to overcome their buoyancy. I understand that Mr. H. H. Hall, of New York, the inventor, is negotiating for the construction of a 16-foot tunnel of this kind across the Straits of' Northumberland, between Prince Edward Island and the main-land, and for tunnels in several other places. 4 One of the most interesting uses of this system is in laying water mains out into lakes. The work can be carried on without inter-

Jan 1, 1886

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored. In Mexico, ore grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. The problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, with the greatest profit potential within the framework of Mexican mineral economics and that nation's government policies. Socio-economic Posture Mexico, prior to World War II, had suffered from more than one hundred years of intermittent wars and exploitation by internal and foreign elements. Consequently, the basic facilities which today's society takes for granted were scarce or non-existent in most of the country. Travel was largely a matter of negotiating poor dirt roads, riding horseback or walking. Relatively few people were literate and medical facilities were luxuries for the wealthy. Mexico's leaders were, however, determined to improve the lot of their people, within a system of private enterprise and personal freedom. Long-range programs initiated at about the time of World War II to provide infrastructure-education, health and welfare, transportation, power, water, communication-are now established fully or in part for most of the country and are being continually expanded.

Jan 12, 1972

By Percival Roberts

IT may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or paddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By Richard Pearce

IN looking around me for some subject on which to frame an address for this meeting, it has occurred to me that some results of observation and investigation, in regard to the varied conditions under which gold is found, may possibly prove of interest. The subject is one which frequently crops up in discussions at our meetings, but there is always an immense amount of uncertainty expressed as to the actual condition in which the gold exists in any particular ore. It follows, therefore, that any light which might be shed on this rather complex subject, would be of value to science and of service to mining and metallurgical practice. In some investigations which I have, from time to time, been led to make, for the purpose of determining to what extent an ore might be concentrated, I have been astonished at the very varied and apparently inexplicable results encountered, and have been naturally led to inquire into the causes for such seeming inconsistency. The mines of Gilpin county, Colorado, where gold was first discovered in that State, furnish an infinite variety of examples of its occurrence, and it was here that difficulties first presented themselves to the Colorado miners, in the sudden transition from what is called " free-milling gold-ore " to an ore characterized by properties which make the ordinary treatment by amalgamation stamp-mills utterly impracticable. So long as mining was limited to what might be called the zone of oxidation in the veins, just so long might amalgamation be conducted without difficulty; but directly the miner reached a point beyond the influence of the oxidizing power of the surface waters, the gold resisted all attempts at amalgamation, and recourse • was had to smelting.

Jan 1, 1890

By Ralph E. Hartline, Wilfred Tapper

The Strataflow process for locating water entry in producing, wells is now available. This method as now practiced utilizes the fact that fluids of different salinities have different electrical resistivities. By introducing into the well a fluid of a markedly different salinity than that of the fluid being produced, a pronounced resistivity change will occur at the point of entry. By running a Strataflow survey the points of major and minor water entry may be interpreted from changes in the resistivity of fluid in the hole. Strataflow results are obtained with the well operating under almost normal producing conditions, and are a logical primary step in any workover program, having as its purpose shutting off of the water. INTRODUCTION Water production is a serious problem in many producing oil wells. It certainly increases lifting costs and in some cases presents a disposal problem. It often aggravates corrosion problems and can even endanger oil production. With accurate information to guide an effective workover program, many marginal wells could be restored to Profitable Production. The shortcomings of previous meth- ods of water entry location were recognized. The Strataflow process is the result of several years of development and field testing directed toward overcoming these limitations. It represents the continued development of a process reported by Silverman and Brown. The earlier work established the basic soundness of fresh-to-salt water resistivity contrast in delineating zones of water entry, but its application was limited by the difficulty of maintaining static balance of the well during preparation for the test. A more serious deterrent to its use, however. was its unadaptability to existing well logging service equipment and field operating methods. STRATAFLOW PRINCIPLE The general principle of the new method involves, first, conditioning the well by displacing the fluid in the bore of the well adjacent to the zone to be tested by a conditioning fluid which is miscible with the formation fluid. This displacement is carried out without interruption of the well production. The conditioning fluid must have some measurable physical, chemical, nuclear, or electrical property which is distinctive from that of the formation fluid. As the well continues to produce. formation liquid entering the well bore dilutes the conditioning fluid so that zones of entry may be determined by making a log of the property undergoing change. This general principle may be applied to indicate zones of either water or oil entry by suitable selection of conditioning fluid and proper logging equipment. The Strataflow process, as it is currently practiced for water entry location, uses fresh water as the conditioning fluid and depends for its operation upon the marked difference of electrical resistivity between this fresh water and the salty water produced by the formations. If possible. any necessary modifications of the well equipment are made a week or so before the test. The well is then returned to normal production. On the day the test is to be carried out. the conditioning water is landed at the bottom of the well and the test is made without interrupting production except for a brief period required for the conditioning water to consolidate into a continuous column extending to a point well above the test section. With this general description of the process in mind, a more detailed step-by-step description of the process will be clearer. PRELIMINARY PREPARATION OF WELL The Strataflow survey, as it is currently practiced for water entry location, is applicable only to pumping wells. Since the required electrical measurements are made by a special

Jan 1, 1952

By Donald E. Scheck, Da-Rong Chou

The application of geostatistics to coal reserve analysis is discussed. One problem in particular, the selection of the optimum locations for exploratory drill holes, is considered in detail. A new interactive program to help the geologist determine the best locations is described and applied to a specific property. The steps in the process are described and then illustrated using a mine's actual data. First, a variogram is selected based on graphical displayed information from the known sample data. Kriging estimates are made for the region of interest and the blocks within the region. The location of future exploratory drill holes is selected based on the criterion of minimizing the region estimation variance for a given number of exploratory holes. The least number of exploratory holes required to meet a specified upper limit on the regional variance is also determined. The computer generated recommendations for the exploratory drill holes are compared to a manually prepared drilling plan. The post- drilling analysis of the results is compared to the predicted values.

Jan 1, 1983

By J. P. Norris, W. T. Pettijohn

The Mufulira Copper Mine, Ltd., is in Northern Rhodesia, ten miles from the Belgian Congo border, and is one of the group of four operating mines comprising the Northern Rhodesian Copperbelt. The ore deposits at Mufulira are on the limb of a large syncline striking NW.-SE. and dipping NE. at about 45 deg towards the Congo border. The host rocks are well-consolidated, highly-silicified, felspathic quarzites of the lower part of the pre-Cambrian Séries des Mines of the Katanga. The ore rocks are underlain, unconformably, by the older "Muva Series," in this case hard, green, metamorphosed quarzites. There are three superimposed orebodies, the first, or upper, orebody averaging 40-ft true thickness with a strike length of about 5000 ft, the second, or middle, orebody of about 50-ft true thickness with a strike length of about 6000 ft, and the third or lower orebody of around 60-ft true thickness with a strike length of 8000 ft. The orebodies are separated by varying widths of waste, or very low-grade ore, from a few feet up to 50 ft. The middle and lower orebodies are so close together for a strike length of 3000 ft that they are mined as one orebody. In all, the mineralized zone is about 200 ft in true thickness.

Jan 6, 1950

By H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others.

Jan 3, 1951

By E. J. Yoder, N. B. Aughenbaugh, R. B. Johnson

Mineral aggregates experience degradation during field and laboratory compaction. Reduction in the aggregate size is accomplished by abrasion of the particle edges and fracturing of individual pieces which have become overstressed. Little is known of the factors that govern the amount of breakdown experienced for a given situation. A field study was made of the factors affecting aggregate breakdown under compaction using three carbonate aggregates of different physical properties. The preliminary results indicate that rock type, compactive effort, gradation, and thickness of compactive layer are factors which exert the greatest influence. Mineral aggregates experience a mechanical breakdown of some of the aggregate pieces into smaller fragments during any compaction process, whether in the field or laboratory. This phenomenon occurs as abrasion of the sharp edges during movement and reorientation of the particles in densifying and/or as granulation and fracturing of those pieces which have become overstressed. Two types of aggregate breakdown occur in the field. These may be classed in a general category of aggregate degradation.* One occurs during the con- * Aggregate degradation has been defined in many different ways. For this paper it is considered as any breakdown of larger particles into smaller ones, whether mechanical or chemical. struction period and is related to the densification of the aggregate body from a loose state to a relatively dense mass by heavy compaction equipment. This type is almost entirely a mechanical action. The other occurs after the construction period when the roadway has been put into use. This in-service breakdown is; a different phenomenon from the breakdown during construction in the sense that it combines mechanical with chemical changes. Time becomes an important consideration that may cause subordinate factors in construction degradation to develop into principal ones for in-service breakdown. Breakdown of aggregates in service has been extensively studied by investigators from the northwestern

Jan 1, 1962

By Louis A. Panek

MOST roof bolts are used in mines with bedded roofs, but it has not been determined to what degree thin-bedded roofs can be reinforced by bolting if there is no thick member in which to anchor the bolts, or what function the bolts must perform in such a case. Owing to widespread practice of sys- tematic bolting to support thin-bedded roofs, moreover, it is desirable to design roof-bolting systems on a quantitative basis. Specifically, a solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, what is the optimum length, spacing, orientation, and tightness of bolts consistent with safety and economy? The investigation reviewed here has produced a functional equation to evaluate these variables and establish basic principles of roof bolting.

Jan 1, 1956

In the late 19th century Fremont Pass was only a gateway to Leadville, Colo., 12 miles to the north. Some of the silver, lead, and zinc won from this famous camp crossed the Continental Divide at Climax, passing by the huge outcrop of molybdenum on Bartlett Mountain. This element, relatively un- known in the world of commerce, was then nothing more than a joke to play on greenhorn prospectors. Even 30 or 40 years later, after the demand for metals created by World War I had forced temporary use of molybdenum as an alternate for tungsten in tool steels, the Bartlett Mountain outcrop once again became merely a curiosity. With the persistent efforts of Brainerd Phillipson, for years the president of Climax and almost the only employe, use of molybdenum gradually began to grow, first in tool steel and later in the alloy steels required by the growing automotive industry. Mr. Phillipson was first an engineer and second a salesman. The combination of these two qualities is the key to the story, not only of Climax sales but also of the growth of molybdenum from an object of idle curiosity to the point where it is today, along with chromium and nickel, one of the most versatile alloying elements in the iron and steel industries and increasingly important in chemistry.

Aug 1, 1955

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guanacaste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active: (2) the Atlantic low-lands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from o to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By B. B. Gottsberger

HAVE given considerable thought during the past year to the subject of licensing of engineers and par-ticularly to the position which the mining engineer should take on this question. I have found, however, that it is not a subject which yields much result for the thought expended on it. So far as any published record will show, mining engineers have been either ignorant of the extent to which the movement for the licensing of engineers has progressed or else indifferent to it. It is true that the Mining and Metallurgical Society of America, by a questionnaire sent out to its member-ship, did a great deal in calling this matter to the atten-tion of the mining profession, and so far as I know, the report of its committee, which analyzed the replies received, is the only published statement of the feelings and opinions of our branch of the engineering profes-sion. It is to be hoped that the conclusions shown by that report, namely, that mining engineers are almost unanimously opposed to the principle of licensing and consequently any legislation dealing with it, has received serious thought and that we are ready for an even more thorough consideration of the subject.

Jan 3, 1922

By Thomas M. Chatard

Every one engaged in the mining of phosphates is well aware that the price he gets for his product depends upon tile results of chemical analysis. He knows that the value rises with the percentage of phosphoric acid, whether stated as such or as so-called " bone phosphate," and that deductions are made for certain constituents, such as alumina or oxide of iron, when the amount of these exceeds certain limits. The reason for these deductions is but vaguely understood by many, and there are few who possess the special knowledge required to form a competent judgment, either as to the reli-

Jan 1, 1893

By James P. Kimball

THE object of the present memoir is to put on record some practical experiments by the writer in smelting a silicious native magnetite with no other flux than the silicates of its own gangue: This work was undertaken in the spring of 1878 for Messrs. Naylor & Co., of Boston, to whom I am indebted for the privilege of here communicating its results, these having hitherto only been simply announced.* So far as I am aware these are the first instances of the kind in this country that non-calcareous; or rather non-carbonated, magnetites have successfully been used strictly alone as self-fluxing ores in the blast furnace; that is, without the addition of calcareous flux in the form either of limestone, quicklime, calcareous ore, or basic (calcareous). slag. Previous to the spring of 1878, when the Chateaugay magnetic ore was first brought to my notice, its use had been limited to Catalan forges, after "separation" at the ore bed. The blooms and billets made from it in the several forges of Messrs. Weed & Williams, and of Mr. Williams, were well known in the trade as among the best in the market. The Chateaugay ore beds proving of great magnitude, and the ore exceptionally low in phosphoric acid, it commended itself for blast-furnace purposes to Messrs. Naylor & Co., who employed nee to blow-in the charcoal furnace at Pittsford, Vt., on this ore in the spring of 1878., a previous trial of this ore in the same furnace in the fall of 1877 having proved abortive. This was therefore the first time that Chateaugay ore was successfully smelted in a blast furnace, although since well known as a blast-furnace ore possessing superior and exceptional qualities. The Pittsford furnace, although rebuilt in 1844, and subsequently improved by the former owner, the late J. Prichard, is one of the few furnaces of the old type with open breast (Sumpfofen) still active in this country. Its improvements on furnaces of the period, * Bulletin American Iron and Steel Association, XII, 1878, 132, 156.

Jan 1, 1881