Search Documents

By J. Spotts McDowell

J. W. RICHARDS, So. Bethlehem, Pa.-The paper is certainly an exceedingly, valuable one and it gives detailed information which should be utilized in the following way. There are probably twenty different circumstances or conditions under which silica bricks are used. Sometimes they are used under high pressure, at others under low pressure, at times for low temperatures and others for very high temperatures. If the methods of this paper are followed out, and if the precise mechanical and thermal properties are determined and can be reproduced, the industry can furnish the proper brick for any particular purpose. There is at present only an imperfect classification made as to properties and uses, but we need a "much more scientific classification of the uses to which the bricks are to be put and then should manufacture the bricks suited particularly for each of those purposes. There is one property which is not mentioned in the paper and which is of considerable importance, that is, the 'electrical conductivity. There may be other properties besides, which a good research laboratory can determine, and when we have listed all the various properties and noted the way in which they can be reproduced, the maker can then specify his exact requirements and the corresponding quality of brick can he selected or made to meet them. H. D. HIBBARD, Plainfield, N. J.-About a year ago I had some experience in another country, in melting steel, where silica bricks made in that country failed, but in a different way from those in America. Here, when the bricks get too hot, they are partly melted and string down

Jan 4, 1917

By Peter Kos

Since advances in the understanding of gravity thickening reflects the development of knowledge about suspensions themselves, the paper starts with the discussion of flocculent and nonflocculent suspensions. The properties of flocculent suspensions and their behavior in different concentration regions (zone settling, channelling, compression) are defined and discussed. In the main portion of the paper, the behavior of flocculent and nonflocculent suspensions during batch as well as continuous thickening, is presented, together with a brief review of the gravity thickening theories and sizing methods. The classical as well as the most recently developed methods are presented and their use and limitations are discussed.

Jan 1, 1980

By Thomas Chance

ALL gravity methods for the separation of ore from gangue, or of slate and other refuse from coal, are based upon differences in the falling velocities, in some fluid medium such as air or water, of the materials to be separated. As all materials falling in a vacuum have the same velocity, independent of the size, shape, weight or specific gravity of their individual particles, it would be more accurate to describe the operation of these methods as depending upon the. retardation of falling velocities effected by the resistance of a fluid medium, this retardation being greater for small or light particles than for large or heavy particles. This generalization is true also of those appliances utilizing centrifugal force to replace or to supplement the action of gravity. The separation of materials of different specific gravities by means of a fluid having a specific gravity greater than that of the lighter particles and less than that of the heavier particles has not been applied commercially, or on a large scale, to the separation of ores or to the washing of coal, the method being limited to laboratory experimental work or to laboratory determinations for the purpose of checking up the work of jigs, classifiers, and other types of concentrating appliances. A solution of zinc chloride has thus come into general use inn the laboratory to separate coal, bony coal and slate, both to check up the work of coal-washing plants and for the purpose of making tests preliminary to the designing of coal-washing plants. The use of a heavy solution of some chemical in water has often been proposed for making such separations, especially in connection with the washing or preparation of coal. Practically insuperable difficulties, however, have prevented the commercial development of any such process, the difficulties being both physical and financial. The cost of the chemical used to make high-gravity solutions is usually prohibitive, and the freeing of the coal from all traces of the chemical is found to be practically impossible. Such solutions inevitably penetrate the individual lumps and particles of coal, transfusing into the pores and saturating the joint-planes, and very large quantities of wash water

Jan 2, 1918

By W. P. Blake

Forging under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various park of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

By T. A. Read, H. M. Otte

THEORETICAL analysis by Wechsler, Lieberman and Read of the crystallography of martensite formation has shown that the requirement for the existence of a macroscopically undistorted plane between austenite and martensite permits a calculation of the indices of the habit plane of the marten-

Jan 1, 1958

The difficulty of finding new ore bodies, the complexities of patenting them when they are found, and the absence of incentive legislation for exploration have limited mining exploration in the United States mostly to the big companies. This situation, coupled with ECA spending abroad, has caused American capital to look outside our national boundaries for investment opportunities which are further made attractive by some relaxing of restrictions to gain American dollars and patronage.

Jan 1, 1950

By Duane E. Eubanks, David B. McDonald

The anticipated growth of western coal production over the next decade is expected to add approximately 274.3 million t/y (302.4 million stpy) to US capacity. The increased output, coming from both new mines and expansion of existing facilities, promises to bring with it a new set of problems for mine planners.

Jan 8, 1976

By Sunder S. Saluja

Man had to learn to break rocks as early as the Stone Age, when they formed his main source of raw material. He started with chipping and over the years has reached a stage where he can employ atomic blasts and break, with one blast, millions of tons of rock. In between these two extremes there have been several stages of development including firesetting, use of the expansion of water on freezing in chipped cracks in cold climates, the use of low or deflagrating explosive black powder in about the 17th century, the use of high explosives with the discovery of nitroglycerine in 1846 by Sobrero, followed by the monumental discoveries of the great Swedish scientist Alfred Nobel in the latter half of the nineteenth century. The attempts to develop a stronger and still stronger explosive force were accompanied by investigations to understand the mechanism of failure of rock so that the force could be used to the best advantage; the latter, of course, have lagged far behind the former. This is mainly due to the fact that the chemical reactions involving high explosives as well as the processes resulting in the breakage of rock take place at too great a rate to be studied with the equipment that has been only recently available. Moreover, the development of stronger explosive forces was prompted by military necessities in the past and competition, at present, among highly developed nations. With the development, however, of the new techniques such as micro- second photography, microsecond flash radiography, extremely high-speed movies, strain gage assemblies, electronic chronographs and other improved electronic techniques, the investigator has in the last decade or

Jan 1, 1968

By E. J. Freeh, W. E. Horst

Mathematical models of a continuous comminution process are developed as an extension of the batch grinding model. Pilot-scale experimental work is described and the results are used to demonstrate the capability of the comminution models to simulate observed behavior over a relatively wide range of process variables.

Jan 1, 1973

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a common occurrence in coal mines of the Northern Appalachian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and formation of cutter roof failure. In-mine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dikes registered the greatest amount of roof loading near the intersection of dikes with the rib. Load cells measuring horizontal pressure changes in the roof indicated that the greatest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysis of rock pressure monitoring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectively support the roof in areas of clastic dikes and prevent cutter roof failure. However, these methods were only successful when employed shortly after mining.

Jan 1, 1984

By F. J. Arriagada

A conventional technique used to process auriferous sulfidic concentrates involves a pre-leach oxidative-roast step. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. Surface analytical techniques such as scanning electron microscopy and BET gas adsorption have been utilized to determine quantitatively the structural morphology of calcined pyrite and arsenopyrite samples in the range of 450 to 750 °C under an oxidizing atmosphere. In the case of. pyrite calcines a highly porous hematite product was found below 500 °C; at higher temperatures, a coarser oxide network , was observed. The surface area of these calcines was found to decrease sharply with increase in temperature. In contrast, the surface area of arsenopyrite calcines was found to follow a bimodal-type behavior with roasting temperature with maxima at 500 and 625 °C. In the case of pyritelarsenopyrite mixtures, the surface area was observed to increase dramatically as the content of pyrite increased. The appearance of pyrrhotite as an intermediate phase in the oxidation reactions is postulated to have important structural implications.

Jan 1, 1984

By Charles Baskerville

SHALES containing,"kerogen,," or bituminous matter, which on destructive distillation yield oily and tarry matters resembling petroleum are here designated as oil-shales. They differ from oil-bearing shales from which petroleum may be obtained by so-called mechanical means. The educts obtained by the destructive distillation resemble some or all the varieties of petroleum, depending on the character of the shale and the mode of treatment. Some shale oils have e a paraffin base, some an asphaltic base, or a combination; some run high in sulfur compounds, The methods of refining and cracking, therefore, are essentially the Sam as are used in refining petroleums. In 1860, in this country, over fifty companies were successfully distilling various bituminous natural materials for the production of "coal oil," used for illuminating purposes. The discovery of petroleum and the failure of these companies to save and utilize the valuable byproduct, ammonia, brought about their inevitable doom. Prior to that time, more or less successful efforts were made to produce from the shales of Scotland oils for illuminating and heating purposes. Competition of native petroleum from the United States early eliminated some of these companies and with the entrance of oil from the Russian and other fields into the world's markets, the Scottish oil-shale industry underwent serious and trying experiences until, in 1916, only four (Scottish) were paying concerns.. These survived only through energy and the application of skill in saving valuable byproducts. A few companies have successfully operated in France and New Zealand. The Canadian Government showed active interest in the New Brunswick shales, which exist in quantity and are more valuable than the Scottish shales. The retarded development of that very valuable asset of the Province of New Brunswick involves a pathetic history, which is lamentable. This was especially true when the product was so much needed in the prosecution of the war. The economic success of a shale-oil industry depends on the following factors:

Jan 6, 1919

By John A. Church

EARLY in the month of August, 1877, a miner in Gold Hill, Nevada, made the unlucky remark that, according to his observation, that month was usually quite free from accidents in the mines. Never was presage wider from the truth. When the month closed twelve mishaps had occurred, killing six and wounding nine persons, and for the rest of that year the Comstock mining communities were kept in a ferment by the frequent occurrence of appalling disasters. There was a real tidal wave of calamity sweeping over the mines, which has not been repeated since, and according to common report was never known before on the Comstock. I was much interested in studying the character of these misfortunes, which also aroused concerted action on the part of the miners, and I have collected a list of the accidents which took place from July, 1877, to May, 1879. The number in this period of twenty-two months

Jan 1, 1880

By John A. Church

Early in the month of Angust, 1877, a miner in Gold Hill, Nevada, made the unlucky remark that, according to his observation, that month was usually quite free from accidents in the mines. Never was presage wider from the truth. When the month closed twelve mishaps had occurred, killing six and wounding nine persons, and for the rest of that year the Comstock mining communities were kept in a ferment by the frequent occurrence of appalling disasters. There was a real tidal wave of calamity sweeping over the mines, which has not been repeated since, and according to cornmoll report was never known before on the Comstock. I was much interested in studying the character of these misfortunes, which also aroused concerted action on the part of the miners, and I have collected a list of the accidents which took place from July, 1877, to May, 1879. The number in this period of twenty-two mouths

Jan 1, 1880

By S. F. Emmons

[The following notes of observations made during a visit of a few days in the month of October, 1886, which was cut short by a sudden summons East, are offered, in spite of their incomplete and tentative character, in the hope that they may aid the members of the Institute, in their coming visit to this region, to a clearer understanding of the general geological conditions under which the ore-bodies occur.] The Butte mining region lies in a sort of a depression in the mountains which is drained by Silver Bow creek and its various tributaries. On the east it is bounded by high north and south ridges of granite, and on the west by lower ridges, also running north and south, which, as far as examined, were found to consist of rhyolite. High mountains also inclose the depression on the north and south, but at a greater distance than the more immediate bounding ridges on the east and west, the distance between which is hardly more than six miles.

Jan 1, 1888

By John W. Cobb

The attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinitions of the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia,. at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal; and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in &other way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 1, 1925

By Eckley B. Coxe

I DES~RE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsylvania, about miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By R. N. Singh, A. S. Atkins

One of the most difficult problems associated with modern mechanised longwall mining is the lack of system flexibility to deal with local changes in geology, seam thickness and the face design parameters. As a consequence of system rigidity and the quest for increasing the coal face performance, the percentage extraction in the U.K. is currently below 52%. The paper outlines the current guidelines used in face design which permit coal to be left in situ for various purposes and discusses the strata control implications in extracting subsequent panels in the same and adjacent coal seams. The paper examines the application of strata mechanics to the design of longwall layouts for maximizing .the percentage of coal extraction. Remedial measures include optimizing pillar dimensions, reduction in roof coal left for support purposes by improving the use of available powered support technology and application of thick seam mining methods including sub-level caving and techniques of extracting coal from odd shaped pillars. Case studies are described where coal extraction has been maximized by adopting a new single heading retreat mining system; a shallow seam partial extraction system utilizing, existing heading machines and minimisin8 coal sterilization in pillars by replacing longwall access roadways by goaf scour.

Jan 1, 1984

By Ernest Lilley

THE tin deposits of Cornwall appear to have been worked for at least 3000 years. Prior to the sixteenth century, the tin came exclusively from alluvial deposits. At that time, shallow pits or mines were started in the hill sections. Mining of copper seems to have begun at the same time, but does not appear to have been especially important until about 1700. From that time until the close of the nineteenth century, copper was of major importance. Lead, and to a lesser extent, other metals, such as antimony, iron and manganese, were produced in commercial quantities during the same period. With the opening of the eighteenth century carne increasing difficulties with water because of the increasing depth of the mines. Among the efforts made to overcome this difficulty was the construction of the "Great County Adit," begun in 1748, taking 20 years to complete, and with its branches having a length of 20 miles. Adits proved capable of handling-only a few of the water problems, and led to rapid adoption of the steam pumping engine in the latter part of the eighteenth century and the early part of the nineteenth. It was in this period that the Cornish pumping engine, still considered by Cornishmen to be the most satis-factory unit for handling large quantities of water, carne into existence. The development of a means of controlling the water made possible the opening up of a number of rich deposits where profitable work-ing was further assisted by numerous improvements in mining and milling machinery. During the middle of the past century, Cornwall, with an average yearly production of 10,000 tons of tin metal and an even slightly larger tonnage of copper, enjoyed a period of unprecedented prosperity. How-ever, the relatively high prices of both copper and tin served not only to encourage prospecting (and much speculation) in Cornwall, but also in other countries. The rapid development of copper mines in the United States, together with sudden impoverishment of the lodes with increasing depth in the greatest of the Cornish copper mines, brought the copper boom to an abrupt end, the production of copper at the close of the cen-tury being negligible in importance and being secured in large measure

Jan 1, 1932