Search Documents

By Zay Jeffries

IT HAS been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat and cooling either rapidly or slowly with nearly pure iron and slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point, which is near 700° C. The present paper will not consider these old and well-known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, in 1886, reports that both working steel and heat treatment of steel in the blue-heat range are highly injurious. Recently, however, some metallurgists believe that the straightening of warped steel forgings at a blue heat produces a beneficial effect on the metal.2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes -in Iron and Steel Below the Thermal Critical Range, which has the following personnel: R. R. Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F.C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood: This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 2, 1920

Established as a Society February 26, 1957 John S Bell, President Wayne E Glenn, President-elect Basil P Kantzer, Past President R E Howard, Vice, President M B Penn, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Bldg Dallas 1, Texas

Jan 1, 1959

[L. W. KEMPF, Chairman E. E. SCHUMACHER, Past-Chairman E. A. ANDERSON, Senior Vice-Chairman A. A. SMITH, JR., Vice-Chairman 11. A. MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N. Y. Executive Committee 1947 C. Y. CLAYTON A. B. GRENINGER CURTIS PIGOTT 1948 WALTER BONSACK W. A. DEAN LOUIS JORDAN 1949 J. D. HANAWALT W. A. JOHNSON E. W. PALMER]

Jan 1, 1946

By R. W. Parsons

The over-all apparent single-phase permeability of fracture-rock systems was studied using two different two-dimensional models. In a strict sense the results are applicable only to these models, yet may give some insight into real reseruoir behavior. The regular fracture-matrix model can have any number of regular fracture sets. All fractures within each set have the same orientation, width and spacing. The gross behavior is amlytically equivalent to that of an anisotropic permeable medium. In the heterogeneous fracture systems, individual fracture conductivities vary within a two-dinensioml network pattern. A computer program calculates the overall permeability after the conductivities are randomly placed in the network. The calculated permeability depends upon the distribution of these conductivities and the particular fracture pattern into which they are placed. Although detailed information on actual reseruoir fracture systems is not available, this study shows how some of the possible variables may affect obserued gross reservoir characteristics. INTRODUCTION Characteristics of reservoir rocks are determined by direct (core analysis) or indirect (logging and production tests) examination. Both methods, singly and together, are widely used in reservoir evaluations. For fractured reservoirs a problem exists in relating characteristics of cores to the in situ reservoir properties. Knowing fracture characteristics can be of value in determining production mechanisms. Because of the limitations of observation, the intimate details of a fractured rock system will never be known. One approach in analyzing fractures is to study the behavior of some conceptually simple models. The two models analyzed contain features which may be realistic, yet are mathematically tractable. Flow is considered in two dimensions only, with the plane of interest at right angles with the fractures. This concept represents the horizontal flow in a reservoir system with the fractures oriented vertically. Only single-phase, laminar flow is considered. The regular fracture-rock system permeability is calculable from a simple analytical expression. The heterogeneous system requires a computer program for calculating overall permeability.

Jan 1, 1967

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By T. Egleston

The materials containing copper which are refined in the United Statrs, are, for the most part, the natiye noppers of Lake Superior. IJntil quite recently but little pig copper Was made for sale, and that came principally from the pure sulphorous ores of New England and the Sonth, and was generally sdd to reSneries not far from the ore filrnaceu. A stnall aiuoiint found its way into the'niarket which was produced either as the by-product of the treatment of gold and silver ores, or as the result of the treatment of impure copper ores; but both these grades, on account of the impurities they contained, were loolced on with stlspicion, and were not sought for. A11 the grtlGis of pig coppcr are sold by the unit of oopper contents, a great redtiction being made in the price when impurities are present. There are at the present time only three works which treat native copper, the two of the Detroit and Lake Superior copper Company, and the works of C:G. Hussey & Co., in Pittsburgh. There are a few works ivhich smelt sulphuroris ores and refine their pig; bo sides these t1le1-e arc a few siuall works where gig copper is refined uuly. Some of these purcIlase blscir copper, refine scrap, or simply refine such grades of ingot copper as are found in the market, but nlostly that from Lake Superior, for the purpose of getting it into swh shapes that can be handled cpmtriercially to advantage, such as in making large plates or high grades of wire fir electrical purposes. A nomher of such works are situated in the Xaugaturk Vatley aud elsewhcre in New England. The recent discoveryof vnlt~sblc ores in Ariarona makm it probable that within a few year8 the refining of capper In the United States will make great develupments. Up to the time of the discovery of the mines on Lake Superior, only a very small quantity of native copper had ever been foond, not sufficient to justify the erection of worlrs fbr its special treatment. It had, besides, never been found in very large maweq so that the discovery of greabblocks of it presented serious difficulties, not oolp in mining it,-I- but in bringing it into a merchantable condit'ion. It seemed a very simple process to melt these large maws,

Jan 1, 1881

This discussion was prepared by members of the Phelps Dodge Corpn. staff who were designated to review the minutes. It is confidential but permission has been granted to distribute copies among those who attended the Conference. The minutes of the above conference contain numerous references to the plants and practices of Phelps Dodge Corporation. As many of these references are inaccurate, the following notes are made covering such points: Construction Magnesite Brick in Reverb. Arch (1) An.18" arch, 20 feet long, was built on one furnace with 5 feet on each side of magnesite brick, the center portion .being of silica brick. The furnace was put in operation February 13, 1930 and on April 23rd after 68.8 days' operation it was replaced due to failure of the silica brick forming the center of the arch. At this time, while the silica brick had completely gone, there was 14" of magnesite left. Bridgewall Tapping (2) Tapping matte through the burner wall was first tried at the Copper Queen Smelter in April, 1925. At that time, a copper casting with 1 ½ extra heavy pipes for water cooling cast in it, and having one taphole block was used. Later, on the other (old) furnaces, similar castings, but equipped with two tapholes, were used. We found with these furnaces that we could tap through the burner wall at the beginning of a campaign, but would subsequently have to go back to side wall tapping. This was the case until sometime in 1926. The new furnaces, that went in operation at the beginning of 1927, each had water. cooled castings with two tapholes. These have been used entirely and have been quite successful. Sometime after the furnaces were put into operation sidewall tapholes were put in, simply for the removal of any accumulation of matte that might be temporarily retained at the front end by bridges or dams in the furnace formed by overcharging locally.

Jan 1, 1930

[Pumps: oil-well: plunger: essential parts, G26, 130; 74, 828 improved type, 74, 846 leakage, 74, 837 operating cycle, 74, 833 Uren design, G26, 145 sucker-rod failures, G26, 136 sucker-rod stress, 74, 835 sucker rods, 74, 830, 832 tubing, 74, 833 tubing difficulties, G25, 138; 74, 836 Olivite, 73, 337 valve and seats, 74, 832 Punching: Monel metal, 78, 86 nickel, 78, 86 Punjab. See Indian Empire. PUPIN, M. L biography, M26, 113 John Fritz medalist, 1931, M81, 499 recipient of Washington Award, M28, 155 PURDY, R.: Discussions: on Relative Efficiencies of Domestic Fuels in Relation to Their Costs and Their Advantages 108, 353 on Uses on Coal in the Ceramic Industry, 108,389,398]

Jan 1, 1936

By L. C. Graton

[CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick11 H. E. McKinstry6 R. H. Clarke 13 D. H. McLaughlin8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Certain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17G. M. Fowler 21 C. H. Behre, Jr21L. C. Graton18 J. S. Brown 16G. F. Loughlin18 E. L. Bruce 19R. H. Sales 19 R. H. Clarke 20A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Mining Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell29G. B. Langford 29 T. M. Broderick28G. F. Loughlin25 E. Y. Dougherty27R. H. Sales 24 G. M. Fowler 22F. A. Thomson 26 I. B. Joralemon 22Edward Wisser 30 General S. F. Kelly35 References36

Jan 1, 1940

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880's, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940's. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

Organization Place Date 1917 Electric Power Club Hot Springs, Va. June 11-14 Society for the Promotion of Engineering Edu¬ cation Evansville,Ind. June 19-22 American Institute of Chemical Engineers Buffalo, N. Y, June 20-22 American Institute of Electrical Engineers Hot Springs, Va. June 25 American Society for Testing Materials Atlantic City, N. J. June 26-30 Mine Inspectors Institute of U. S. A. Indianapolis Ind. July 9-11 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Exposition of Safety and, Sanitation .. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers.... Philadelphia, Pa. Sept. 10-14

Jan 6, 1917

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler 2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick 11 H. E. McKinstry 6 R. H. Clarke 13 D. H. McLaughlin 8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse 13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon 11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Cer¬tain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17 G. M. Fowler 21 C. H. Behre, Jr 21 L. C. Graton 18 J. S. Brown 16 G. F. Loughlin 18 E. L. Bruce 19 R. H. Sales 19 R. H. Clarke 20 A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Min¬ing Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell 29 G. B. Langford 29 T. M. Broderick 28 G. F. Loughlin 25 E. Y. Dougherty 27 R. H. Sales 24 G. M. Fowler 22 F. A. Thomson 26 I. B. Joralemon 22 Edward Wisser 30 General S. F. Kelly 35 References 36

Jan 1, 1940

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

By R. C. Earlougher

Jan 1, 1970

CONTENTS PAGE Simons, Theodore.-Basic Principles of Gravity Concentration-A Mathematical Study : :.. 1 Taggart, Arthur F. and Gaudin, A. M.-Surface Tension and Adsorption Phenomena in Flotation 11 Hersam, Ernest A.-Factors Controlling the Capacity of Rock Crushers 12 Shaw, S. F.-The Ore Deposits of Sierra Mojada, Coahuila, Mexico 12 Wilson, Philip D.-The British Columbia Batholith and Related Ore Deposits 26 Greensfelder, N. S.-Shot-firing by Electricity 27 Mitke, Chas. A.-Metal Mine Ventilation in the Southwest 28 Foley, F. B. and Howell, S. P.-Neumann Bands as Evidence of Action of Explosives upon Metals 30 Schwartz, H. A., Payne, H. R., Gorton, A. F., and Austin, M. M.-Conditions of Stable Equilibrium in Iron-carbon Alloys 30

Jan 12, 1922

By Charles A. Kliche

INTRODUCTION The Northern Great Plains Coal Province which occupies approximately 36.6 ha contains about one-half of the nation's total coal resources. About one million ha are underlain by coal that is considered to be mineable from the surface. The topography of the province is predominately plains, rolling hills, and some badland areas characterized by breaks or sharply eroded hills. Elevations range from about 1500 m above sea level on the west to about 600 m above sea level on the eastern boundary. The average slope of the ground is approximately 2 m per km. Streams in the province drain generally easterly and southeasterly (1). In the United States, the Northern Great Plains Province lies within the states of North Dakota, South Dakota, Montana, Wyoming, Nebraska, and Colorado. The coal within the province is located almost entirely in the states of North Dakota, Montana, and Wyoming. Although it is relatively low rank, the coal within the province encompasses a large portion of the total remaining U. S. reserves. The U. S. Geological Survey estimates the total remaining coal resources of the United States to be 2.6 trillion mt within 1000 m of the surface, and 2.9 trillion tons within 1830 m of the surface. Of this total, only about 177 billion mt are classified as reserves meaning that they are (1) known in location, quantity and quality from geologic evidence supported by engineering measurements, and (2) economically recoverable based on currently available technologies and current market value (2).

Jan 1, 1983