Search Documents

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut, and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States, 2 and in addition, feldspar is produced as a byproduct by firms whose major products are spodumene and mica. 3 Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan, and the USSR. According to the US Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 and 2,514,000 t, respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel, tile, and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, NC, have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water containing 0.9-1.0 ppm fluoride will seldom cause mottled enamel on children's teeth; and for adults, concentrations less than 3-4 are not likely to cause endemic cumulative fluorosis and skeletal effect. Although the literature on this subject is rather confusing and inconclusive, the inference that concentrations over 4 ppm may affect bone structure is clear. According to the recent Federal Register,4 maximum fluoride level of 1.4 ppm at 79°-98°F is considered to be adequate and safe for the protection of health of the consumers. The EPA and state environmental agencies have accelerated their drive to reduce water pollution on a faster schedule. By 1977, the EPA specifications for maximum contaminant level of fluoride ions in the discharge waters of feldspar milling operatins is expected to be reduced to 2.0 ppm. The other problems of using hydrofluoric acid are the following: toxicity, hazards of handling and storage, and high cost as compared to other inorganic acids (almost 16 times the cost of sulfuric acid). In order to reduce fluoride levels in mill discharge waters, mining companies have taken the following steps: I) Recirculating a part of their mill water. Even though recirculation of mill water seems to be a novel method of reducing fluoride contamination of the discharge water, there are certain operational and handling problems. 2) Conducting research on the treatment of fluorides in mill waste water. The technology of treatment of fluoride ions has received considerable interest in the recent years. A recent research report5 estimates that the cost of fluoride ion removal to meet the present specifications in the feldspar industry is approximately $0.25/t of ore processed, and about $0.50/t of feldspar produced. At the request of the feldspar producing industries in North Carolina, the North Carolina State University (NCSU) Minerals Research Laboratory has taken up a research program directed towards overcoming the fluoride ion pollution problem. After a close study of the operational, technical, and economic aspects of feldspar flotation, it was decided to attempt to replace the conventional hydrofluoric acid process. Conventional Feldspar Flotatin Using Hydrofluoric Acid Since the inception of the feldspar flotation process using hydrofluoric acid by O'Meara2,6 the process has achieved a great commercial success. In the conventional flotation separation of feldspar-quartz, hydrofluoric acid is used to suppress quartz and activate feldspar, and a long chain amine salt (acetate or chloride) is used as a collector. The bulk of amine collectors used in current feldspar operations are applied as the water-soluble acetates of the free-base amines. These products are pastes or waxy solids which are available in a range of acetic acid neutralization levels generally 50 to 100% neutralized. In spite of the problems mentioned in connection with the use of hydrofluoric acid, this process is extremely stable with respect to changes in the process variables. With the exception of a few operations, alaskite and pegmatite are the major sources of feldspar.7 In the flotation treatment of a pegmatite that contains iron-bearing minerals (heavy minerals), mica, feldspar, and silica, a logical order of removal presents itself considering the following:8 1) Mica is readily floated by an amine collector in a pulp pH 3.5. Some iron-bearing minerals will usually respond to amine collector in acid circuit with the mica concentrate. 2) Since iron minerals tend to occur invariably in the feldspar concentrate, it is desirable to remove most of these prior to feldspar flotation. A fatty acid or a petroleum sulfonate collector used in this flotation step in acid circuit will float iron-bearing minerals. 3) Using hydrofluoric acid to maintain pH of 2.5, an amine collector employed in a final step will float feldspar away from silica, usually leaving the latter in the tailing as a high-grade silica concentrate. The problems connected with the flotation separation of feldspar-quartz arise due to the similarities in their chemical structure. Therefore, any reagent system that is likely to succeed in feldspar-quartz separation should have adsorption affinity towards one of the minerals and depression effect towards the other mineral.

Jan 1, 1979

By Clarence Zener

THE heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an under- standing will involve two distinct types of inquiry: (I) the direction of the trans- formation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed here in steel such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron- alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data being obtained from the simple binary and ternary equilibrium diagrams. FUNDAMENTAL EQUATIONS In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body- centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may be regarded as filling all the lattice positions of a given type. The introduction of the fundamental equations of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1946

By C. W. Hall

MINE executives, as a rule, have always been willing to adopt new ideas of operation, or to listen to proposals which might increase the effectiveness of their enterprise, more especially so if they could be shown how definite results might be attained by introducing any conception suggested. In these days of high wages, high cost of supplies, and high taxes, operators are even more inclined to accord consideration to innovations or improvements, and many go so far as to employ men to conduct special investigations and make studies for the purpose of advancing production. Where a man is brought into an organization to do work of an efficiency nature, it often creates resentment among the operative heads because of having their work directly scrutinized, or investigated, and there is a tendency, if not actually to obstruct, to fa.il to cooperate; in which case the investigator is handi-

Jan 1, 1925

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By Arthur S. Huey

AS the end of the collegiate year approaches, the problem of student employment again becomes acute. This subject divides itself into two phases: (1) employment prior to graduation and (2) employment following graduation. "Experience is the best teacher," according to the old adage, and the student needs all that he can get. He is afforded every opportunity to reap from his books the theories and principles of scientific and engineering practice, and occasionally he is privileged to make field trips to observe the practical side of the subject. But it is not enough for one to know the theory and to observe its application; it is also desirable for the student to get the feel of the tools during his training Such opportunities can only be afforded the student if the major companies cooperate with the universities in giving the student part-time and vacation work.

Jan 1, 1932

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core. For this reason neither analysis of core recovered (amounting to 37.5 pct of approximately 10,000 ft of hole drilled) nor sludge analysis considered separately would give correct assays. The following equation has been adopted: actual weight theoretical actual weight core — theoretical weight sludge Drilling is done un.der contract. Collection of core and sludge samples together with double-checked assaying is done by the company. Microscopic, specto-graphic, and X-ray examination of rock specimen saved is carried on at the University of Utah. A fund, set up by Kennecott Copper Corp. at the University, has encouraged cooperation in solution of mining research problems. The drill used is a Longyear hydraulic powered by a Waukesha 26-hp gasoline motor. A pump, Bean Royal type, is powered by a 7-hp Briggs-Stratton gasoline motor. Weight of unit is 4000 lb and is placed under tripod of 35-ft wood poles within a 25-ft sq area. The following results have been attained: Avg depth of hole drilled, ft 1215 Avg drilling depth per 8-hr shift, ft 10.11 Core Size, In. Avg depth of NC casing, ft 21 2 11/16 Avg depth of NX casing and size core, ft 178 2Ye Avg depth of BX casing and size core. ft 427 1% Avg depth of AX casing and size core, ft 585 1 5/32 Through the use of metal sludge collection boxes, 12 ft long, 18 in. wide, and varying from 12 to 24 in. in depth, sludge recovery has been maintained above 95 pct. Samples, both core and sludge, are assembled for each sample interval and averaged in 50-ft bench increments. Determinations for mineral values are made at both the mine and mill. Assay results varying in excess of 0.05 of copper assay values are rerun to determine correct assay. The organization chart for the Kennecott Utah copper mine is shown in Fig. 1. The Utah mine requires approximately four men per shovel shift to drill solid rock, properly slope banks, and trim loose material from the top of bench sections in making them safe for men and equipment working below. During recent years, while the mine has been worked day and night, powder crews have worked day shift only. Series of toe holes drilled back of advancing electric shovels comprise approximately 70 pct of all mine drilling. These holes, spaced about 21 ft apart, have a depth of 24 ft. Of the footage drilled, 25 pct is for vertical holes either 24 or 28 ft deep, spaced about 28 ft centers along the top rim of banks. This combination of toe holes, using an Ingersol-Rand DA 35 drifter mounted on a tripod and the vertical holes using an Ingersol-Rand Type X71 wagon drill is standard practice above the pit elevation. These benches are 68 ft high, with a few exceptions, while benches below the pit elevation are 50 ft high and require very little drilling other than toe holes. Five benches, varying in height from 80 to 100 ft, require a combination of toe holes plus vertical holes and bank holes or electric churn drill holes. Bank holes using the DA 35 drifter and electric churn drill using Bucyrus-Erie Model 29T, account for 5 pct of feet drilled. Until the past year, drilling of fill material on upper levels was accomplished by churn drill method. Wagon drills are now used for fills because they can be set up and drill a hole an hour. It is necessary to run an air drill 7 hr for each 8-hr shovel shift. Average drilling rates during the past year were as follows: DA 35 drifter using 2 and 3-man crews — 4.36 ft per man hr X 71 wagon drill using 2-man crews — 6.45 ft per man hr DA 35 drifter bank holes, 3-man crews — 2.53 ft per man hr Bucyrus-Erie churn drill, 2-man crews —1.9 ft per man hr Total mine avg — 4.57 ft per man hr Mine practice assigns powdermen to job locations where they perform all drilling and blasting work within the area. Almost as much labor is consumed in springing and loading holes as in drilling them. Average powder consumption is approximately as follows: Per Electric Shovel Shift, Lb To spring and chamber holes — 50 Blasting — 500 Trim banks — 50 One fifth of all powder used is Hercules hercomite bag powder while four fifths is Hercules gelamite 65 pct strength in 1 Vi in. x 8 in. sticks. Frozen material, overhanging from top banks, creates a winter hazard to shovel operators and equipment. Experiments are being conducted with a high-speed Hercules powder in an effort to eliminate this condition. Banks are trimmed by powdermen who lodge 8 or 10 bundles of powder, containing 15 or 20 sticks each, across the upper surfaces of each working face. To each bundle of powder is attached a primer with 6-ft fuse which is lighted as the powdermen, who have lowered themselves down the bank on ropes, ascend to safety. Three angle dozers, D8 caterpillars, make grades and move supplies for the average 31 drilling machines working daily. Compressed air is furnished by three Ingersol-Rand compressors, each with rated capacity of 3750 cu ft of air per min at 100 lb reservoir pressure.

Jan 1, 1952

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By J. W. Evans

ONE possible method for the separation of hafnium from zirconium is by the vapor phase oxidation of the purified mixed chlorides. An important factor for success depends on the difference in free energies of the following reactions: ZrCl(g) + O2 = ZrO2(s) + 2C12 [1] HfCl4(g) + O2 = HfO2(s) + 2C12. [2] Prakash and Sundaram1 have calculated these values from certain data and carried out experimental work with partial success. However, their free energy values for reaction 2 diverge rather widely from other data which are presented here. The possibility of successful separation is briefly considered in the light of these alternative values. Table I shows the free energy values (?F°) for reactions 1 and 2 derived from the recent compilation of data on oxides and chlorides by Glassner.2 The corresponding values of Prakash and Sundaram for the same temperatures are also shown. The alternative values to those of Prakash and Sundaram for reaction 2 are substantially confirmed by the data of Kubaschewski and Evans" and Cough-lin' on heats of formation, entropies, and heats of vaporization. In spite of the considerable uncertainty in the hafnium data it is reasonable to suppose that the oxide-chloride free energy difference for two such chemically similar elements would not be very far apart. These figures indicate clearly that the oxidation of hafnium chloride is appreciable at all temperatures. Nevertheless, there is a significant difference between the values for reactions 1 and 2

Jan 1, 1959

By E. T. Knight, John D. Gill

IN ITS capacity for service to the public the oil industry is truly gargantuan. But it is only in this respect that the industry is the voracious, many-headed, many-armed and many-handed creature it has been so often painted by those who know it not too intimately and only from the outside. Contrasted sharply with the immensity of the service rendered is the relatively modest share of the national income which has gone to those who provided the tools and the mental and manual labor with which the service was performed. No doubt the relative meagreness of the re- ward was the result of a combination of fortuitous circumstances respecting the nature and accessibility of the industry's raw material and the extensive development and application of the most advanced technology, spurred by an intense competition.

Jan 1, 1940

CONTENTS PAGE THOENEN, J. R.-Limestone Production as a Mining Problem. Discussed by Oliver Bowles, J. T. Singewald, S. R. Russell 1 GRIGGS, C. C.-Engineering in Limestone Production. Discussed by W. C. Phalen, John Rice, Samuel M. Shallcross, Oliver Bowles, Nathan C. Rockwood, George Milliron 2 WILDER, FRANK A.-Rotary Calciners for Gypsum. Discussed by L. K. Arm-strong 9 PORTER, JOHN J.-Manufacturing Problems of Cement Industry. Discussed by Samuel M. Shallcross 9 KIRKHAM, VIRGIL R. D.-Phosphate Deposits of Idaho and Their Relation to the World Supply. Discussed by F. A. Wilder, S. L. Willis, G. R. Mansfield, R. W. Stone, L. K. Armstrong 9 Limestone Production as a Mining Problem Discussion of the paper of J. R. THOENEN, presented at the New York Meeting, February, 1925, and issued, as Paper 1417-H, with MINING AND METALLURGY, February, 1925. OLIVER BOWLES, New Brunswick, N. J.-I am so thoroughly convinced of the growing importance of underground work in the production of limestone that I had the author make a detailed study of limestone mining for the Bureau of Mines and prepare a report on the principles of limestone mining. Many limestone operators, long accustomed to open¬pit work, are being forced to mining. About 6 months ago I thought there were twenty-five or thirty underground limestone operations in the United States but the author has been finding new ones until his list now runs nearer sixty. Some of these are very extensive; one at least has 4 ½ miles of underground workings. There is an ever-expanding field for the engineer in the operation of limestone mines and quarries. Some of the larger companies realize the need of skilled engineering advice, but many of the companies regard the engineer as an unnecessary expense. Although almost every metal mine, even those handling only a few hundred tons of ore per month, employs a mining engineer, many limestone operations ten times as large employ no mining engineers. Few mining engineers are at all familiar

Jan 6, 1925

By Nicholas J. Grant, Italo S. Servi

Extensive data of minimum creep rates and rupture times for high purity and commercial aluminum confirm the existence of a transition range from the low temperature-type to the high temperature-type behavior. The data are analyzed in line with the suggested theories of deformation of metals. CONSIDERABLY more work has been done on the rupture and creep behavior of commercial alloys than on the less complex, high purity metals. As a result, certain fundamental behaviors are overlooked. One of the lesser known variables affecting the high temperature behavior of metals is the impurity content (or alloy content). Impurities are known to affect strongly the recrystallization temperature, electrical resistivity, and other properties of metals, but the effect on creep and other high temperature mechanical properties has been determined for very few materials. In view of these facts aluminum appears to be a fairly ideal metal, since it is available in a wide range of purity contents from 99.995+ down through the 2s (99.0 + Al) and 3s (1.2 Mn) grades in small steps. It is highly resistant to oxidation and other surface instabilities, leaving recrystallization and grain growth as virtually the only instabilities. Control of grain size is also well standardized. Limited data on the creep of aluminum have been obtained by Dushman et a1.l for high purity aluminum; by Sherby2 on 2s aluminum of variable grain size; and by Dorn and Tietz³ on cold-worked 3s aluminum. Experimental Procedure The apparatus consisted of a constant stress, creep testing unit similar to the type described by Hop-kin.' The specimens were held at temperature for 30 min before loading. The loading time was less than 2 min. Factors affecting the accuracy of the data were: 1-—the temperature gradient and control, ± 3°F; 2-the stress determinations, ± 1.5 pct; and 3—elongation measurements (1 in. gage), ? 0.001 in. Three grades of aluminum were tested: 1— high purity (99.995 pct Al), 2—2s (99.3 pct Al), and 3—3s (98.2 pct Al). The spectrographic analyses of these materials are reported in Table I. The specimens were annealed then electropolished in a perchloric-acetic mixture before testing. Data on heat treatments and grain size obtained appear in Table 11. The entire creep curve was determined for almost all of the tests. A few tests were interrupted after the beginning of the third stage of creep, and in these cases the rupture time was estimated. Experimental Results Constant stress creep-rupture testing gives a much longer, more accurately measurable second stage of creep than constant load testing. This behavior is in agreement with the results obtained by Andrade for lead (see Fig. 1). If the test is run to completion, the third stage of creep appears as soon as stress intensification occurs. In the case of specimens which fail in a ductile manner, the stress intensification begins when the sample starts "necking". This differs from the "high temperature brittle" specimens in which the stress intensification is caused by intercrystalline cracking. These specimens

Jan 1, 1952

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926

By Fred J. Miller

FRED J. MILLER was born in Ohio, in 1857. He had a common and high school education, supplemented by personal study and special instruction. After serving a 4-year apprenticeship and working in various capacities in machine shops, he became a contributor to mechanical journals and finally a member of the editorial staff of The American Machinist, where he remained for twenty years, the last ten years as editor-in-chief of the magazine, and vice-president of the publishing company. On retiring from journalism, he was for nine years general manager of a group of typewriter factories, and was then commissioned Major of Ordnance in the U. S. Army, being stationed during most of his service at Rock Island Arsenal, where he organized the Civilian Service Division of the Arsenal. He is now a member of the Technical Advisory Committee of the War Claims Board at Washington. Major Miller became a member of the American Society of Mechanical Engineers in 1890, and has always taken an active interest in its affairs, having served on a number of important committees, and as a member of Council from 1904 to 1907, inclusive. He was elected President in December, 1919.

Jan 1, 1920

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with low ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the size range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for vari¬ous reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully.

Jan 1, 1953

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959