Search Documents

By P. K. Foster, A. McNabb

A consideration of the literature shows the inadequacy of Fick's Laws to describe the diffusion of hydrogen in steels below 400°C. These laws are modified an the assumption that hydrogen is delayed at fixed sites in the lattice. Approximate and exact solutions of the resulting nonlinear system are derived for simple geometrical shapes. The results qualitatively account for the observed anomalous behavior. Experimental methods for verifying the theory are suggested. 1 HIS paper presents a new analysis of the diffusion behavior of hydrogen in steel based on a physical model which supposes that hydrogen atoms wander in a random manner through the crystal lattice, but tend to get trapped or delayed at certain fixed sites uniformly distributed throughout the metal. These sites, which will be called traps, are regarded merely as potential wells of significantly greater depth than those encountered in regular regions of the crystal lattices and no assumptions are made concerning their nature or origin. The results of experimental studies of the diffusion of hydrogen in iron and steel have usually been reported in the literature in terms of a diffusion constant D derived under the assumptions that the hydrogen concentration C is governed by Fick's laws.1 Fig. I is a composite of published graphs of the man. ner in which the values of D, so derived, vary with temperature. It is convenient to consider this material in two categories; the high temperature results above 400°C, and the results at lower temperatures. The graphs 2, 3, 4, 5 in the first class lie within a factor of three of each other and are relatively consistent compared with the low-temperature values. There is an increasing divergence in values of D with decreasing temperature till at room temperature they are spread over three orders of magnitude. Small values of D have been obtained for work-hardened specimens.' It is evident that D is a function of other variables besides temperature in this range and that these neglected variables are in some way connected with the work hardening experienced by the specimen. In view of evidence for an interaction between hydrogen in solution and dislocations9'10 and adsorption on crack surfaces,' some doubts must be entertained about the validity of Fick's laws and their associated physical model of noninteracting particles in random motion through the medium. More direct evidence of their inapplicability to the diffusion of hydrogen in steel was first produced by Darken and smith." Consider the permeation of hydrogen through a plate of thickness a under a boundary concentration Co at the ingoing, and zero at the outgoing, face. If Fick's first law1 is valid, the steady state flux P, through unit area is DCo/a. In addition, the concentration C varies linearly throughout and Qo, the mean quantity of hydrogen in the medium, is co/2. Compare Qo with Q1 the mean quantity required to saturate the same specimen to a uniform concentration G. In this case Ql = Co and hence the ratio

Jan 1, 1963

By AIME AIME

THE Board of Trustees, made up of three from each of the four societies, conducts the business com- mitted to United Engineering Society by its Founder Societies under its Charter, the Founder's Agreement and the Library Agreement. A draft of a budget of revenue and expenditures for the ensuing calendar year is presented each September to the secretaries of the Founder Societies for the information and comment of their governing bodies. After revision, the budget is adopted, by the incoming Board of Trustees at its meeting in January.

Jan 1, 1929

By P. K. Currie, J. V. Walters

Solution mining of magnesium salts (Carnallite and Bischofite) is taking place near Veendam, in the northeast Netherlands. The magnesium salts are used for the production of magnesia sinter, used as a base material for the manufacture of refractory bricks for furnaces. This paper gives, first, an introduction to the operational procedure followed in Veendam, with the emphasis on some of the unique aspects, and then discusses rock-mechanical aspects of the cavity behaviour. The creep behaviour of magnesium salts is described, and Finite Element calculations on cavity stability and potential surface subsidence are discussed.

Jan 1, 1985

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee. Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails. The shaft is 12 ft 7 1/2 in. ID of the concrete walls. This is large enough for two 10-ton hoisting skips and a ladder compartment. One of the skip compartments is for hauling equipment. The grouting equipment was a 2%xlO-in. Gardner-Denver grout pump, air powered and developing 1000 lb pressure. A grout mixer, also air driven, fed the mixed solution into a tank coupled to the pump suction. Grout materials used were mostly water and Portland cement. Some Bentonite was used to seal porous ground near the surface.

Jan 11, 1950

By Charles Bohdanowicz

Production of crude in 1937 decreased (Tables 1 and 5) by about 2 per cent, while gas production for that period increased by about 6 per cent after a slight decrease in 1936 (0.4 per cent).' As in preceding years, drilling operations were confined principally to extensions of old oil fields in the Jaslo district (fields 1 and 7) and to some extent to such extensions in the Stanislawbw district (field 27). Deepening of old wells to horizons reached more recently by new wells gave on the average better results per well than those attained by new wells (Table 3). Reserves of proved lands have increased some by new oil fields discovered, Targowiska (field 8) and Czarna (field 19) both of which, however, have only small production. The Daszawa gas field (field 25) has not been extended, but two new gas fields were located instead— Opary, distant 25 km. (151/2 miles) northwest of Daszawa, Balicze at 12 km. (7 1/4 miles) southeast of Daszawa, and Kalusz (TESP Company exploiting potassium salts) in the vicinity of the town of that name (field 33). Drilling upon the gas area near Tarnbw and Debica, while gas-bearing sandstone had been found at depths of from 300 to 512 meters (984 to 1680 ft.) (Zdziary No. 2) and at 220 m. (722 ft.) [pressure 11 atmospheres, flow 24 cu. m. per min. (847 cu. ft.)] (Przyborbw No. l), has not as yet ascertained horizons qualified for permanent exploitation. The exploring well near Kos6w remained for the last seven months at the depth of 1420 m. because of the collapse of rotary drilling pipe. Below the 300-m. level no gas sands have been encountered at this well. Gas Reserves In connection with the broad plan of developing industrially the sector of Poland lying between the Vistula and the San Rivers, and extending farther north as far as the city of Radom, there arose the necessity of a more accurate calculation of gas reserves for the fields of

Jan 1, 1938

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By C. L. Shapiro, R. Schempp

DuRing the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these characteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and emphasized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent carbon. The discrepancies encountered in the determination and classification of the austenitic grain size led to an investigation of some of the variants influencing the austenitic grain size as determined by standard methods. Methods of Determining Austenitic Grain Size The present methods used for the determination of the austenitic grain size may briefly be classified in two groups: 1. Etching at room temperature to reveal the austenite grain size prior to cooling. 2. Etching at elevated temperatures, cooling to room temperature, and observing the structural conditions that existed at the temperature from which cooling occurred. The outstanding methods of the first group are: (1) the McQuaid-Ehn test, (2) optimum rate of cooling, (3) quenching and etching. McQuaid-Ehn Test.—This established and accepted test does not need much elaboration. It consists of pack carburizing at a definite temperature for a standard period of time and slowly cooling in the furnace. The temperature is 1700" F. (925' C.) and the time is 8 hr. The interpretation and evaluation of this test are fairly well defined in the A.S.T.M.

Jan 1, 1937

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By AIME AIME

ON Sept. 24, 1875, a remarkable deposit of silver ore was discovered by James Ryan and Samuel Hawkes at the east base of Grampian Hill in central Beaver County, Utah.. A shaft was begun and had been sunk about 30 ft. in ore when the claim was sold on Feb. 17, 1876, to A. G. Campbell, Matthew Cullen, Dennis Ryan, and A. Byram for $25,000. To them is due the credit of having developed the mine and started the district on the road to its present state of prosperity. Their development resulted in proving the vein to a depth of over 280 ft. and about 2500 tons of ore was extracted and turned into bullion. In February, 1879, the mine came into the possession of the Horn Silver Mining Co., and since then over $65,000,000 worth of ore has been taken from the mine. Two smelters were built in 1878, near the mine; 400 men were employed underground, and 1000 on the surface, burning charcoal, hauling wood from the surrounding hills, and freighting and hauling hay for the hundreds of horses used in the work. Ore was hauled thirty miles to the

Jan 1, 1936

By Ian Wark

IN an earlier paper1 measurements of contact angles due to the effect of xanthates on mineral surfaces were reported. The solutions in which these measurements were made differed widely from those of modern flotation circuits. It is intended, however, by introducing, one at a time, the other principal reagents of flotation, to approach gradually the solu-tion composition of flotation liquors. The work now described is an attempt to determine the effect of one of the most important of these reagents-namely, sodium cyanide-on the establishment of air-mineral contact. The work has been carried out for the following companies: Broken Hill South, North Broken Hill, Zinc Corporation, Electro-lytic Zinc of Australasia, Mount Lyell Mining and Railway, and Burma Corporation. Since the effect of cyanide is inseparably connected with the alkalinity, the results cited below deal with the mutual effects of alkalis and cyanide. Alkalis alone exert a significant effect on the air-mineral contact but comparatively large amounts are required. Since the addition of a small amount of cyanide greatly decreases the degree of alkalinity necessary for the suppression of contact at surfaces of any of the minerals experimented with (except galena) and since alkalis are rarely used alone in practice, little attention has been paid to cyanide-free solutions. It was shown in the previous paper that, excluding the dixanthogen effect, whenever contact was practicable at all in an ethyl xanthate solution the angle of contact was 60°. There is, therefore, less necessity to measure equilibrium contact angles; in fact, the experiments herein described have generally been conducted with a view to determining whether contact is possible and not to measuring the actual value of the contact angle. The separations which have generally to be effected in dealing with complex sulfide ores are: (1) galena from sphalerite, pyrite, etc.; (2) sphalerite from pyrite and/or gangue minerals; (3) copper minerals from pyrite and gangue minerals; (4) pyrite from gangue minerals; (5) chal-

Jan 1, 1933

By J. H. Clemes

The process of leaching silver ores with sodium hyposulphite is comparatively new, and published accounts of the details and losses of the process are as yet very few. The following account of a careful series of experiments to determine the actual loss in this process may therefore be acceptable to members of the Institute. The ore treated was highly calcareous, and the principal sulphide present was iron pyrites. Following is an analysis by Professor Price, of San Francisco, of the ore treated : Per cent. Silica,..........15.13 Sulphur,.........13.31 Arsenic,.......... 9.82 Iron............ 17.33 Alumina,..........1.35 Zinc,...........4.92 Lead,..........1.78 Carbonate of lime,..33.78 Magnesia,.......... 2.58 100.00 Ten tons were crushed dry with a 30 X 30 screen = 900 holes per square inch. In order to feel our way with this ore, two experimental or "pilot" charges were roasted. Pilot Charge No. 1. Treated 1000 pounds in a four-hearth reverberatory. 8.30 p.m.—Entered fourth hearth, remaining there one and onehalf hours; sulphur began to burn. 10 p.m.—Changed to third hearth; ore became red-hot half an hour after entering; the fireplace was kept almost destitute of fuel. 2.30 A.M.—Changed to second hearth. Charge continued, giving off a large quantity of sulphurous fume; the fireplace was kept dark.

Jan 1, 1884

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By E. W. Pehrson, J. W. Furness

THE method of presentation in the accompanying charts is based upon the well-known formula: production plus imports minus exports equals apparent consumption. Thus for each area for which data are shown there are two columns of equal height, one representing production plus imports, the other apparent consumption plus exports. Usually no account has been taken of increases or decreases in stocks. All columns and flow lines are drawn to a linear scale which is supplemented by figures showing the actual quantities represented. Owing to the small area occupied by the European countries on the world map it was impossible to show the details of the trade of the individual countries. All of Europe (except Russia), therefore, is shown as a single unit. However, statistics of production and consumption indicated elsewhere on the charts show the degree of self-sufficiency enjoyed by the major European powers.

Jan 1, 1936

By Richard W. Smith

Why are we losing our liberties? (1) . . . because our local chambers of commerce come to the National Chamber's annual meeting, vote for a policy on federal economy, and then go to Capitol Hill and ask for a federal project for their area. (2) ... because our mining men ask for a subsidy to mine submarginal deposits that can't be economically mined in a free economy. (3) . . . because 18,000 men and organizations all over the country recently wired or wrote a Congressional committee asking that the Army Engineers be exempt from the President's power to reorganize the Executive Branch of the government under the recommendations of the Hoover Commission.

Jan 1, 1949

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen'l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O'C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen'l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By Leo H. Glanville

Until 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115 000 cu, ft. per min., and since then fans and sprays have been added as required. Atmospheric Conditions Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the norma1 average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low—about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the Year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24" to 75°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in Part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,470 ft.], makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. Problems since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination, It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By E. M. Cox, T. Rosenqvist

IN a recent investigation, carried out at the Institute for the Study of Metals, the affinity of sul-phur for iron, copper, and manganese was studied over the temperature range 700" to 1300°C.' It was found that copper exhibits a rather high affinity for sulphur, especially at higher temperatures; and attention was called to the possibility that copper when present together with sulphur in liquid steel would tend to lower the chemical activity of sulphur and thus interfere with the desulphurization process. It was clear, however, that the data for the equilibrium between pure copper and pure copper sulphide (Cu2S) could not give any quantitative information about the effect of copper when dissolved in liquid steel. The present work is concerned with the activity of sulphur in the diluted range of the binary iron-sulphur system, and with the influence of small amounts of copper on this sulphur activity. This investigation is in principle based on the same method previously described for the binary metal-sulphur studies;1,2 namely, reaction with hydrogen to form hydrogen sulphide. The equilibrium ratio PH2s/Ph2 in the equilibrium gas mixture is, for a given temperature, directly proportional to the sulphur activity. The activity of sulphur in liquid iron has previously been studied by Chipman and Ta Li,3 White and Skelly,4 and recently by Sherman, Elvander, and Chipman.5 Morris and Williams6 have studied the effect of added silicon, and Kitchener, Bockris and Liberman,7 and recently Morris and Buehl,8 the effect of added carbon on the sulphur activity. In present day steelmaking processes the steel bath contains between 0.01 and 0.1 pct sulphur, and the copper content may be as high as 0.5 pct. The equi-librium gas ratio (H2S/H2) would, for such a low-sulphur content, be too low to be measured with the experimental technique we use. It has been shown by previous investigators that the H2S/H2 ratio is closely proportional to the sulphur content up to about 1 pct sulphur. The sulphur activity at very low-sulphur content can therefore be calculated by linear interpolation between 0 and 1 pct sulphur. In order to show the general trend with increasing sulphur content, the present work has been carried out to about 3.5 pct sulphur. As the effect of copper was assumed to be more a function of the Cu/S ratio than of the absolute copper content, the runs with copper were made for certain constant values for this ratio.

Jan 1, 1951

By C. O. Brawner

Simple, specific rules for achieving slope stability in open-pit mines are impossible to devise. Each pit has a different mining program and a different set of environmental conditions, and its final slope design must be based on an individual evaluation of the actual site. The overall philosophy of pit stability, however, is tending towards a limit design concept. Since slope angle has a great influence on the economics of most open-pit mines, efforts are being made to reduce the theoretical factor of safety for slope stability to very near 1.0. (Factor of safety is here defined as shear strength/shear stress on the most probable plane of failure.) Actually, where detailed, statistically significant testing has been done and a comprehensive ground control program is being instituted to warn of movement at an early stage, safety factors as low as 1.1 or 1.2 may be justified. The cost of the necessary procedures, however, is high. There are many factors that influence stability, but this article will be confined to three-rock structure, groundwater, and blasting.

Jan 8, 1969