Search Documents

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By Wallace E. Pratt

UNDER the stimulus of war psychology the American public has grown confused and jittery in its thinking on the subject of this nation's petroleum resources. This confusion arises from the failure of the average citizen, and even of many leaders in government, in our armed forces, and in the petroleum industry itself, to distinguish between our proved reserves of petroleum in the several oil-producing states and the total petroleum re- sources available to this nation. Leaders and public alike examine the accepted estimates of our proved reserves and thoughtlessly conclude that these estimates represent the total of our petroleum resources. Our fears are aggravated if we turn to the statistics on oil-finding and observe that the discovery of new reserves has waned decidedly in recent years. This confusion is dangerous because, under its influence, ill - considered policies spring up and flourish, choking out the most valuable fruits of the long experience of the American petroleum industry.

Jan 1, 1944

ALABAMA. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Belle Ellen.-Hutcheson, W. C. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co Dobbs, G. G., Box 97. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., 1. & R. R. Co. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Brown-Marx Bldg. Coxe, E. H. Tenn. C., I. & R. R. Co. Crawford, C. G., Tenn. C., I. & R. R. Co. Crockard, F. H., Brown-Marx Bldg. Ellis, E. E.,1515 Brown-Marx Bldg. Fairbairn C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Geismer, H. S., Keiser-Geismer Engrg. Co.

Jan 1, 1917

By L. J. Howell, R. C. Sommer, H. H. Kellogg

WORK described herein was undertaken with the aim of determining some of the physical-chemical properties of electrolytes suitable for the electrodeposition of pure zirconium metal. In this paper the phase diagram, vapor pressure, and activities in the melt are considered. In a companion paper,' the electrolytic conductivity of some of these melts is reported. The melts studied were mixtures of NaCl and/or KC1 with ZrC1,. Chloride melts were chosen for study because 1) if the electrolyte is to be useful for industrial electrodeposition of zirconium, the chlorides will be preferred to the relatively costly bromides and iodides; 2) fluoride melts were being studied in another laboratory (Horizons Inc., Cleveland); and 3) melts containing oxygen, in any form, are unsuitable for preparation of pure zirconium, because of the great affinity of this metal for oxygen. Unlike electrodeposition from aqueous solution, the fundamental behavior of fused-salt electrolysis is poorly understood. In most cases, such basic electrochemical information as the phase diagram of the melt system, activities in the melt, conductivity, the nature of the current-carrying ions, the equilibrium electrode potentials, and the overvoltage behavior of the electrodes is unknown to the researcher who would develop a new electrodeposition process employing a fused salt. This research project was designed to supply information about some of these basic physical-chemical properties so that an intelligent choice of electrolyte for electrodeposition studies could be made. Experimental The experimental difficulties-encountered in this work result from the properties of zirconium metal and ZrC1,. ZrC1, is a solid which sublimes at 334°C. It is rapidly hydrolyzed by moist air to HC1, ZrOCl,, and ZrO,. Unusual precautions were exercised in this work to prevent hydrolysis of ZrC1, and rigidly to exclude oxygen, nitrogen, hydrogen, and carbon from the melts under study. These elements are known to react with and contaminate zirconium metal. All melts were studied in vacuum systems, i.e., in the presence of ZrC1, vapor only. Transfer of ZrC1, to or from the melts was accomplished entirely by vacuum sublimation. In this way, neither the melts nor the ingredients thereof were permitted to

Jan 1, 1958

By J. J. Predali, J. M. Cases

J. J. Predali and J. M. Cases (Attachè de Recherche and Charge de Recherche, respectively, Centre de Recherches sur la Valorisation des Minerais, Institut Polytechnique de Nancy, Nancy, France)-The role of CO, in carbonate flotation is one of the parameters of a complex phenomenon: the adsorption of salts of fatty acids onto minerals. The authors therefore must be congratulated for their work. Their experimental results suggest some questions: 1) Recovery with C02, benzoic acid, or HCl, look very similar [(Fig. 1)] to that with the use of air; however, the recovery decreases very slightly (<10%). But in these two kinds of experiments, two parameters are different: the pH which is near 5.8 (with C02) becomes 9.1(without C02) and the concentration of Ca* I x 10-3 mole per 1 (without C02) becomes 1.9 X 10&apos; mole per 1 (without COO. 2) Adsorption experiments (Fig. 2) permit computing the surface coverage 9 which is 7.4% (without C02) and 8% (without CO_.) for an initial concentration of 12 X 10-6 mole per 1 in sodium oleate. It seems doubtful to us that this small variation can produce large increases of the recovery in flotation. 3) It is difficult to correlate adsoption and flotation experiments because they do not seem to have been done with the same size of particles. The concentration needed to obtain 95% recovery (Fig. 1) is about 3.0 X 10_" mole per l, that is, 1.13 X 10-6 mole for about

Jan 1, 1973

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

By W. L. Honnold

AS BOTH South Africa and diamond mining are unfamiliar subjects it seems best that on such an occasion as this I should endeavor to reflect the atmosphere of the place and to picture the mines from an industrial rather than from a technical standpoint and, because of long absence, my remarks must necessarily be sketchy and in some particulars not up to date. The preferable route to South Africa is via England, direct steamers from America being inferior as to service and effecting no saving of time. The newer boats are of about 20,000 tons capacity and very comfortable. Seventeen days are required for the voyage and only one stop is made-that at the island of Madiera, three days out. Between Southampton, the port of departure, and Madiera the weather may be warm or cold and the

Jan 1, 1925

By W. R. Ingalls

IF, in this study of the outlook for the copper industry of the United states, I find myself assuming to be prophetic in some respects I shall express myself with hesitation and with the foresight that after the end of the war with Germany the war with Japan may continue; anyway there is sure to be an uneasy period before copper and the other metals begin to flow smoothly through the natural channels of consumption. It is mainly my purpose to survey conditions and suggest some probabilities, or possibilities, rather than to prophesy. In interpreting them it will be necessary to make certain aasurnptions, among which will be (1) expectation of a rise in the general price level,, which so far has been one-sided; (2) continuance of the k. tariff on copper imports; and (3) lock-up of government-owned copper as a military re- serve. Of these assumptions the first is indicated by the lessons from economic history, and by current symptoms. The second and third depend upon political action by Congress.

Jan 1, 1944

By Willard L. Cumings, Benjamin L. Miller

(Glen Summit Meeting, June, 1911.) I. THE CAMAGUEY DEPOSITS. 1. Location. THE Camaguey brown iron-ore deposit covers the top of San Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name "San Felipe district " is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,1 who says: "The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camaguey City, in the province of Camaguey Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp 2 has the following to say of ores in Carnaguey Province * Geologist, Bethlehem Steel Co. + Professor of Geology, Lehigh University. 1 Bulletin No. 540, U. S. Geological Survey, p. 324 (1908). 2 The Iron Ore Resources of the World, printed by the Eleventh International Geological Congress, vol. ii., p. 795 (1910).

Mar 1, 1911

By Frederick M. Becket

AFTER all the chronology that has been given, what is the present status of chromium steels? For the purpose of this discussion the different types of chromium steels can be divided into three classifications-those containing relatively low , percentages of chromium, say 5 per cent or less; the medium-chromium steels containing up to about 18 or 19 per cent chromium; and the steels containing still higher percentages of chromium, and some of the special alloys. Chromium has some unique effects in steel, so it is well to make a few generalizations. The affinity of chromium for carbon is great and the metal is unique in the manger in which it supplements and enhances the effects of carbon. Chromium retards -considerably the thermal transformations on cooling and exerts an opposing influence both on the absorption and precipitation of the carbides in steel. These statements make it easy to understand the fact that chromium .steels are capable of producing a hardened product at a much slower rate of cooling than is, true of plain carbon steel, and that chromium carbide or -the mixed carbides of iron and chromium do not contribute to brittleness to as great a degree as does iron carbide.

Jan 1, 1929

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

By Frank Firmstone

In the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.&apos; Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the district, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Lurmann&apos;s cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons&apos;s furnace,2 for it appears from W. Firmstone&apos;s note-books that in October, 1840, he visited " Gibbons&apos; new furnaces building at Corbyn Hall," and I have an old drawing,

Jan 1, 1910

By H. J. Fraser

LIKE a runner catching his second wind, the mining geologist in 1944 has had some opportunity to appraise the result of three years of active and intense search for the metallic sinews of war and peace. The war period has been one of physical activity and accumulation of new data but has not so far resulted in the announcement of any profound or revolutionary theoretical concepts or techniques. Most technical publications during the year have been either descriptive or statistical. A review of accomplishments during the war years, although affording some measure of satisfaction in individual cases or regarding production of certain metals or&apos; ores, is far from justifying any feeling of complacency regarding the growth of the profession either in fundamental knowledge or in application. During 1944 an abundant supply of all metals and minerals flowed steadily to smelters and fabricating plants. Also, during this and preceding years, adequate stock piles for war needs, in view of the improved foreign and domestic supply situation, were accumulated in many metals in such quantities that the mining industry has become concerned not with the problem of supply but with the effect these accumulated stocks, if maintained, might have on the postwar market. These considerations culminated in the enactment by Congress of the Surplus Disposal Act, which, admittedly a tempo-

Jan 1, 1945

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Willard L. Hunter

Four solvent extraction systems were studied to determine their efficiency jor extraction and separation of tantalum and columbium. Aqueous feed solutions of varying HF-HCl concentrations and metal content were contacted with equal volumes of cyclohexanone, 3-methyl-2-butanone, and 2-pentanone and solutions of varying HF-H2S04 concentrations were contacted with equal volumes of 2-pentanone. One multistage continuous test was made in a polyethylene pulse column using cy clohexanone as the organic phase. In each system studied, columbium and tantalum purities in excess of 95 pct with respect to each other were obtained in single-stage tests at low acidities in the feed solution. Separation factors ranging from 1700 to 2400 were obtained when rising HF-HCl mixtures in the aqueous phase. Best results were obtained when a solution of HF-H2S04 was used as the aqueous phase and 2-pentanone as the organic phase. A separation factor in excess of 6000 was obtained in one stage with aqueous solution concentrations of 2 _N HF and 2N H2S0,. When acid concentrations were increaszd to 52 HF and 10 _N H2S0,, 99.9 pct of the tantalum and 98.2 pct of the columbium initially present in the feed solution were transferred to the organic phase. The separation of columnbium and tantalum obtainable by means of the solvent extraction systems presented in this paper was found to corn -pare favorably with other systems, including the HF-H2SO4-methyl isobutyl ketone system currently used by most producers for the extraction and separation of these metals. TANTALUM and columbium are always found together in minerals of commercial significance, although the proportion of the two metals in ores varies within broad limits. Columbium is estimated to be 13 times more abundant than tantalum. Five methods generally employed for the separat:ion of these metals are: 1) fractional crystallization (the Marignac process),2 2) solvent separation, 3) fractional distillation of their chlorides, 4) ion exchange, and 5) selective reduction. Of these methods, the one currently used by industry to the greatest extent is that of solvent separation. One of the early technical developments in solvent separation of tantalum from columbium was reported by the Bureau of Mines: the HF-HC1-methyl isobutyl ketone system; data were presented for both laboratory and pilot-plant experimentation.3 Of twenty-eight organic solvents tested for their ability to extract tantalum from an HF-HC1 solution of columbium and tantalum, 3-pentanone (diethyl ke-tone), cyclohexanone, 2-pentanone, and 3-methyl-2-butanone were chosen for further study. Data on the HF-HC1-diethyl ketone system has been published4 and data describing the use of cy clohexanone, 2-pentanone, and 3-methyl-2-butanone as the organic phase are included in this report. RAW MATERIAL The source of tantalum and columbium oxides for this study was (&apos;Geomines" tin slag from the Manono Smelter, Cie Geomines, Gelges, S.A., Congo. In order to extract the valuable Ta-Cb content, the slags were carbided, chlorinated, and the sublimate from chlo-rination was hydrolized and washed free of chloride with water. The washed material was air-dried and stored in a stoppered container. Throughout the paper, "feed material" refers to this mixture of hydrated oxides which was employed because of its high solubility in aqueous solutions. Typical analysis of the hydrated oxides is shown in Table I. I) HF-HC1-CYCLOHEXANONE SYSTEM Batch Separation. Effect of Acid Concentration. To determine the effect of varying the acid concentration upon the transfer of tantalum and columbium, a series of tests was made in which approximately 2.5 g of feed material was added to 25 ml solutions of 2, 4, 6, 8, and 10 N HF and 0 through 5 N HC1. Tantalum pentoxide concentration of the solu%ons was approximately 21 g per liter and columbium pentoxide was 14 g per liter. These starting solutions were shaken with equal volumes of cyclohexanone in 100 ml polyethylene bottles for 30 min. The phases were carefully separated in 125 ml glass separatory funnels. The time of contact of the solutions with the separatory funnels was kept at a minimum to reduce silica contamination. The measured phases were separated into 400 ml polyethylene beakers and the metal contents of each were precipitated by addition of an excess of ammonium hydroxide. Precipitate from each phase was filtered on ashless filter paper, ignited at 800" to 1000°C for 45 min, weighed, and analyzed by X-ray fluorescence.5 Data tabulated in Table I1 and illustrated in Fig. 1, show that maximum separation of tantalum from columbium for each HF concentration was obtained with no HCl present. The purest tantalum product was obtained with some HCl present. The highest separation factor was obtained at 2 N HF and

Jan 1, 1970

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental &apos;and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner&apos;s equipment; by learning to look at situations through the eyes of all those involved; by developing common &apos;languages&apos; which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

ALABAMA Anniston.-Bretz, J. A. Carrington, F. G. Gerber, A. B. Klugh, B. G. Semple, R. A. Ashland.-Barton, .J. Bessemer.-Abbott, C. E&apos;. Ball, T. L. Beaver, J. J. Ferguson, V. Salmon, H. S. Sehaber, C. F. Whatley, W. J.

Jan 1, 1923

By F. H. Deily, D. S. Rowley, R. J. Howe

By Edward H. Bzirdick

THE territory under particular consideration in this article comprises portions of La Plata and Montezuma Counties, situated in the southwestern corner of Colorado, and around the base of the La Plata Mountains. (See Fig. 1.) In southeastern Utah and northeastern Arizona there are several mountain systems whose origin and structure are practically identical with the La Platas so that ore occurrences found in the latter can be hopefully looked for in the former. With this assumption, there is an area around the laccolithic ranges which offers promise for a successful exploration for gold ores. Ore occurrences of the Silverton, Telluride, Rico, or Ouray Districts will not be discussed, although in these areas the Mesozoic sediments are more or less involved within the ore-bearing complex. These have been intensively studied and developed. The idea is to set forth what my mining experience has been within the largely unaltered . Mesozoic horizon which remains around the extreme bases of the La Plazas. This, until recent years, has been almost entirely neglected by prospectors and operators and, so far as similar territory in Utah and Arizona is concerned, so remains.

Jan 1, 1934

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa&apos;s6 and M. Okamoto&apos;s7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith&apos;s latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter&apos;s diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940