Search Documents

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By Ove Sandberg, Olav Bowitz

The operational characteristics of the Soderberg vertical spike anode are briefly discussed stressing the importance of the flow properties of paste in the fluid zone, the thermal shrinkage in the carbonizing zone, and the surface disintegration in the consumption zone. The requirements for paste recipe and binder quality are combined with design and operation of cell. A low temperature susceptibility of viscosity and low thermal shrinkage of paste together with a low microporosity of the binder coke are important properties. PRACTICAL application of Soderberg's idea of a selfbaking carbon electrode proved successful just before 1920. Shortly after, experimental work was started with the aim of developing a continuous electrode that could be adopted as anode in aluminium reduction cells. The intermittent operation of a large number of small prebaked anodes made the idea of developing a continuous anode for electrolytic production of aluminium especially tempting. Moreover, the electrode consumption in this process, even on a theoretical basis, is very high. Many installations were carried out in the 1930's and during the Second World War. During the tremendous post-war expansion of the aluminium industry, the Soderberg electrode has been steadily more widely adopted. Thus, today more than 60 pct of the Western World's output of aluminium is produced in cells with selfbaking anodes, see Big. 1. The quality of the anode paste of Sfiderberg elec- trodes is considered a major factor influencing the specific carbon consumption. The purpose of this paper is to survey the fundamental requirements which must be met in order to obtain good anode operation. We have limited this paper to a discussion of Elektrokemisk's research on the vertical spike type anode. I) FUNDAMEKI'TALS OF ANODE CARBON PERFORMANCE A) Brief Introduction. The only practical method for producing a conductive carbon anode of the size required is to form and carbonize a mixture of a carbonaceous binder and a precalcined dry aggregate coke. In the Soderberg electrode, the forming and carbonization take place in the electrolytic cell

Jan 1, 1962

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By Charles B. Henderson

DESPITE the loss, by enemy conquest, of a high percentage of our normal sources of supply for tin, the position of this important metal is easier today than that of rubber and a long list of other strategic materials, many of which are produced in this country. Actually, there is no shortage of tin for essential war purposes, owing to a strict control of its use, to increasing considerably the amount of secondary tin available, and to the foresight of the Government in authorizing the Reconstruction Finance Corp., as early as June, 1940, to acquire and produce certain critical and strategic materials of which tin was one of the most important. The construction of the Longhorn Smelter on the Gulf Coast in Texas is an important part of this program.

Jan 1, 1943

By R. B. Hoy, Stanley J. LeFond, K. Reckling

World production of natural diamonds prob¬ably exceeds 50,000,000 carats a year. The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, and the Republic of South Africa third. Diamonds are also mined in South-West Africa, Angola, Ghana, Sierra Leone, and other African coun¬tries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today in India, which was the first source of commercial production. In the U.S., efforts at commercial diamond mining have been con¬fined to a small area near Murfreesboro, Ark. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2000 years ago, only about 130 tons have been mined. In order to obtain 1 g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential ma¬terials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic indus¬trial diamonds are now of a quality that per¬mits wide substitution in the fine-grained sizes. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to "modify" light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem dia¬mond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today. About 1475, a Flemish cutter named Van Gerquem discovered that diamond dust on an iron wheel would polish facets on a diamond to provide more brilliance and fire. Cutters continued to experiment with facets, and shortly before 1700 a Venetian cutter named Peruzzi developed the 58-facet brilliant cut. With the development of the science of optics, cutters have learned more about the behavior of light within the diamond. Early in the 20th century, they learned how to angle Peruzzi's

Jan 1, 1975

By G. A. Vissac

MOISTURE in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain").

Jan 1, 1949

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,' and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Zay Jeffries

IT has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500° C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.1 The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 lb. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is affected in an electric furnace in an air atmosphere,

Jan 9, 1919

By H. M. Day

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy1 in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were con-firmed and supplemented through X-ray analyses by Preston and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower tempera-tures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in the right region.

Jan 1, 1938

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

ALTHOUGH the refining period of the heat is generally defined as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed. semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1951

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs' scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983

By K. C. Gilbart, E. Stansfield

This test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930,1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 1/4 cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings, and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30" to 35" C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the laboratories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 1/4-in. cubes

Jan 1, 1934

Robert T. Hill, Washington, D. C.: Having studied very minutely the geology of the district referred to by Prof. Branner, I beg to state that his quotation of my classification of the Cretaceous deposits of Arkansas is not the one which I originally gave,* nor is it the one which has since been published and is now generally accepted.? I did not assign ally of the Cretaceous formations of Arkansas to the " middle Cretaceous,"

Jan 1, 1898

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923